Hi Mathieu,
first of all, nice to see an attempt to upstream the board. A bit fast
though as upstreaming was planned after the official PHYTEC release.
However, there is quite a lot of differences in respect to the
downstream PHYTEC kernel tree.
I am sure PHYTEC wants to sync here to avoid general confusion.
CC-ing: upstream@xxxxxxxxxxxxxx
So lets start:
- the board should be named "imx93-phyboard-segin" instead of
"imx93-phycore-segin".
PHYTEC naming convention:
phyCORE -> the SoM
phyBOARD -> the base board (with the SoM)
On 17. 01. 24 08:49, Mathieu Othacehe wrote:
> Add DTSI for Phytec i.MX93 System on Module and DTS for Phytec
> i.MX93 on Segin evaluation board.
>
> This version comes with:
> - 1GB LPDDR4 RAM
> - external SD
> - debug UART
> - 1x 100Mbit Ethernet
Maybe you sync this commit msg + title with downstream commit like so:
> arm64: dts: imx93: Add phyBOARD-Segin-i.MX93 support
>
> Add basic support for phyBOARD-Segin-i.MX93.
> Main features are:
> * Ethernet
> * SD-Card
> * UART
>
plus add eMMC to the list if you decided to enable it?
>
> Signed-off-by: Mathieu Othacehe <othacehe@xxxxxxx>
> ---
> arch/arm64/boot/dts/freescale/Makefile | 1 +
> .../dts/freescale/imx93-phycore-segin.dts | 93 +++++++++++++++++++
> .../boot/dts/freescale/imx93-phycore-som.dtsi | 64 +++++++++++++
> 3 files changed, 158 insertions(+)
> create mode 100644 arch/arm64/boot/dts/freescale/imx93-phycore-segin.dts
> create mode 100644 arch/arm64/boot/dts/freescale/imx93-phycore-som.dtsi
>
> diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
> index 2e027675d7bb..f078d6ef75f7 100644
> --- a/arch/arm64/boot/dts/freescale/Makefile
> +++ b/arch/arm64/boot/dts/freescale/Makefile
> @@ -201,6 +201,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8qxp-colibri-iris-v2.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8qxp-mek.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8ulp-evk.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx93-11x11-evk.dtb
> +dtb-$(CONFIG_ARCH_MXC) += imx93-phycore-segin.dtb
Like I said, this has to be renamed to imx93-phyboard-segin.dts as the
official kit name is "phyBOARD-Segin-i.MX93".
> dtb-$(CONFIG_ARCH_MXC) += imx93-tqma9352-mba93xxca.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx93-tqma9352-mba93xxla.dtb
>
> diff --git a/arch/arm64/boot/dts/freescale/imx93-phycore-segin.dts b/arch/arm64/boot/dts/freescale/imx93-phycore-segin.dts
> new file mode 100644
> index 000000000000..748b779a9dc1
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx93-phycore-segin.dts> @@ -0,0 +1,93 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (C) 2023 PHYTEC Messtechnik GmbH
> + * Christoph Stoidner <c.stoidner@xxxxxxxxx>
> + * Copyright (C) 2024 Mathieu Othacehe <m.othacehe@xxxxxxxxx>
> + *
> + */
> +/dts-v1/;
> +
> +#include "imx93-phycore-som.dtsi"
> +
> +/{
> + model = "PHYTEC phyBOARD-Segin-i.MX93";
> + compatible = "phytec,imx93-phycore-segin", "phytec,imx93-phycore-som",
> + "fsl,imx93";
> +
> + chosen {
> + stdout-path = &lpuart1;
> + };
> +
> + reg_usdhc2_vmmc: regulator-usdhc2 {
> + compatible = "regulator-fixed";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>;
> + regulator-name = "VSD_3V3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + gpio = <&gpio3 7 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
Order properties here alphabetically like in the downstream kernel.
Comment applies for the entire patch.
> + };
> +};
> +
> +/* Console */
> +&lpuart1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart1>;
> + status = "okay";
> +};
> +
> +/* SD-Card */
> +&usdhc2 {
> + pinctrl-names = "default", "state_100mhz", "state_200mhz";
> + pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
> + pinctrl-1 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
> + pinctrl-2 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
> + cd-gpios = <&gpio3 00 GPIO_ACTIVE_LOW>;
> + vmmc-supply = <®_usdhc2_vmmc>;
> + bus-width = <4>;
> + status = "okay";
> + no-sdio;
> + no-mmc;
> +};
> +
Please consider adding pinctrl_100mhz and pinctrl_200mhz from the
downstream kernel which were determined by HW measurements at those
operating frequencies.
> +/* Watchdog */
> +&wdog3 {
> + status = "okay";
> +};
> +
> +&iomuxc {
> + pinctrl-names = "default";
> + status = "okay";
Remove this pinctrl + status left-over?
> +
> + pinctrl_uart1: uart1grp {
> + fsl,pins = <
> + MX93_PAD_UART1_RXD__LPUART1_RX 0x31e
> + MX93_PAD_UART1_TXD__LPUART1_TX 0x31e
Please consider pinctrl settings from the down-stream kernel. They differ.
> + >;
> + };
> +
> + pinctrl_reg_usdhc2_vmmc: regusdhc2vmmcgrp {
> + fsl,pins = <
> + MX93_PAD_SD2_RESET_B__GPIO3_IO07 0x31e
> + >;
> + };
> +
> + pinctrl_usdhc2_gpio: usdhc2gpiogrp {
> + fsl,pins = <
> + MX93_PAD_SD2_CD_B__GPIO3_IO00 0x31e
> + >;
> + };
> +
> + pinctrl_usdhc2: usdhc2grp {
> + fsl,pins = <
> + MX93_PAD_SD2_CLK__USDHC2_CLK 0x178e
> + MX93_PAD_SD2_CMD__USDHC2_CMD 0x139e
> + MX93_PAD_SD2_DATA0__USDHC2_DATA0 0x138e
> + MX93_PAD_SD2_DATA1__USDHC2_DATA1 0x138e
> + MX93_PAD_SD2_DATA2__USDHC2_DATA2 0x138e
> + MX93_PAD_SD2_DATA3__USDHC2_DATA3 0x139e
> + MX93_PAD_SD2_VSELECT__USDHC2_VSELECT 0x51e
> + >;
> + };
> +};
> diff --git a/arch/arm64/boot/dts/freescale/imx93-phycore-som.dtsi b/arch/arm64/boot/dts/freescale/imx93-phycore-som.dtsi
> new file mode 100644
> index 000000000000..4edff4a50b2b
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx93-phycore-som.dtsi
> @@ -0,0 +1,64 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (C) 2023 PHYTEC Messtechnik GmbH
> + * Christoph Stoidner <c.stoidner@xxxxxxxxx>
> + * Copyright (C) 2024 Mathieu Othacehe <m.othacehe@xxxxxxxxx>
> + *
> + */
> +/dts-v1/;
> +
> +#include "imx93.dtsi"
> +
> +/{
> + model = "PHYTEC phyCORE-i.MX93";
> + compatible = "phytec,imx93-phycore-som", "fsl,imx93";
> +
> + reserved-memory {
> + ranges;
> + #address-cells = <2>;
> + #size-cells = <2>;
> +
> + linux,cma {
> + compatible = "shared-dma-pool";
> + reusable;
> + alloc-ranges = <0 0x80000000 0 0x40000000>;
> + size = <0 0x10000000>;
> + linux,cma-default;
> + };
> +
> + ele_reserved: ele-reserved@a4120000 {
> + compatible = "shared-dma-pool";
> + reg = <0 0xa4120000 0 0x100000>;
> + no-map;
> + };
Remove ele_reserved if you are not using it anywhere. This only applies
to vendor kernel at the moment.
> + };
> +};
> +
> +/* eMMC */
> +&usdhc1 {
> + pinctrl-names = "default", "state_100mhz", "state_200mhz";
> + pinctrl-0 = <&pinctrl_usdhc1>;
> + pinctrl-1 = <&pinctrl_usdhc1>;
> + pinctrl-2 = <&pinctrl_usdhc1>;
> + bus-width = <8>;
> + non-removable;
> + status = "okay";
Currently only default DDR50 is supported.
So no need for 100mhz + 200mhz pinctrls.
> +};
> +
> +&iomuxc {
> + pinctrl_usdhc1: usdhc1grp {
> + fsl,pins = <
> + MX93_PAD_SD1_CLK__USDHC1_CLK 0x15fe
> + MX93_PAD_SD1_CMD__USDHC1_CMD 0x13fe
> + MX93_PAD_SD1_DATA0__USDHC1_DATA0 0x13fe
> + MX93_PAD_SD1_DATA1__USDHC1_DATA1 0x13fe
> + MX93_PAD_SD1_DATA2__USDHC1_DATA2 0x13fe
> + MX93_PAD_SD1_DATA3__USDHC1_DATA3 0x13fe
> + MX93_PAD_SD1_DATA4__USDHC1_DATA4 0x13fe
> + MX93_PAD_SD1_DATA5__USDHC1_DATA5 0x13fe
> + MX93_PAD_SD1_DATA6__USDHC1_DATA6 0x13fe
> + MX93_PAD_SD1_DATA7__USDHC1_DATA7 0x13fe
> + MX93_PAD_SD1_STROBE__USDHC1_STROBE 0x15fe
> + >;
> + };
> +};
BR,
Primoz
