On Wed, Jan 17, 2024 at 06:15:51PM +0100, Krzysztof Kozlowski wrote:
> On 17/01/2024 17:19, Frank Li wrote:
> >>
> >> Not really, because compatible describes hardware and it is the same
> >> hardware here. We do not have two different compatibles for GPIOs being
> >> input or output. Or two different compatibles for serial engines (ones
> >> providing UART, SPI or I2C).
> >
> > GPIO and UART is simple. Actuall SPI and I2C have two mode, slave and
>
> I talked about serial engines which can be multiple: UART, SPI and I2C.
>
> > master. Many SPI/I2C is dual mode controller. Just seldom use slave mode
> > at linux side. So you just see master mode SPI/I2C controller in dt-binding
> > and dts file. So few people upstream slave part to linux kernel community.
> > They have the exact same problems if support slave mode.
> >
> > PCI is typical example:
> > EP mode: Documentation/devicetree/bindings/pci/qcom,pcie-ep.yaml
> > RC mode: Documentation/devicetree/bindings/pci/qcom,pcie.yaml
> >
> > Which is the same hardware for two difference compatible string.
>
> That's the only case, I recall.
As my knowledge, yes.
>
> >>
> >>>
> >>> I can write git commit message like:
> >>>
> >>> dt-bindings: i3c: svc: add compatible string nxp,imx93-svc-i3c-target
> >>>
> >>> silvaco i3c controller is dual mode controller, which can work as master
> >>> and target mode. All clock, reg, irq are the same for both mode. Add
> >>> compatible string "nxp,imx93-svc-i3c-target" to let silivaco i3c
> >>> controller work as target mode.
> >>>
> >>> Of course, alternate method to added a property "mode" to distingiush
> >>> master and target mode. but old "silvaco,i3c-master-v1" will actually work
> >>> as dual mode support. Driver structure will become complex.
> >>
> >> Please send full DTS of user for this, which works for 100%, so we can
> >> see how it differs from controller mode. If your code snippet from other
> >> thread is correct, then it would suggest "mode" property or lack of
> >> children. Maybe lack of children is not enough, if user-space could
> >> control I3C bus.
> >
> > According to current implment, only need change imx93.dtsi's @i3c1's
> > compatible string to "silvaco,i3c-target-v1". I attached imx93 dts node for
> > your reference.
> >
> > i3c1: i3c-master@44330000 {
> > compatible = "silvaco,i3c-master-v1";
> > ^^^^ only need change here!
>
> Nope, don't change compatibles of existing nodes. Unreadable and
> unmanageable code.
It is just show minimize difference.
Normally, it should be.
i3c1: i3c-master@44330000 {
...
compatible = "silvaco,i3c-master-v1";
...
status = disabled;
}
i3c1-target: i3c-target@44330000 {
...
compatible = "silvaco,i3c-target-v1";
...
status = disabled;
}
in board dts
@i3c1{
status = "okay";
}
Or
@i3c1-target{
status = "okay";
}
>
> >
> > reg = <0x44330000 0x10000>;
> > interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
> > #address-cells = <3>;
> > #size-cells = <0>;
> > clocks = <&clk IMX93_CLK_BUS_AON>,
> > <&clk IMX93_CLK_I3C1_GATE>,
> > <&clk IMX93_CLK_I3C1_SLOW>;
> > clock-names = "pclk", "fast_clk", "slow_clk";
> > dmas = <&edma1 6 0 1>, <&edma1 5 0 0>;
> > dma-names = "rx", "tx";
> > status = "disabled";
> > };
>
> That's not a patch for existing file. I did not claim you cannot write
> such DTS. I claimed you don't have such DTS for upstream...
Yes, it need finialize this topic before handle dts upstream.
>
> >
> > For master mode:
> > Unlike i2c. Genenally I3C can auto probe children node like USB can auto
> > detect attached devices. So I3C master can work without children nodes.
> > Such as auto load i3c sensor driver according to i3c standard vendor id and
> > production id.
>
> Then presence of children cannot be used.
>
> >
> > For target mode: using configfs to controller I3C.
> >
> > mkdir /sys/kernel/config/i3c_target/functions/tty/t
> > echo 0x011b > /sys/kernel/config/i3c_target/functions/tty/t/vendor_id
> > echo 0x1000 > /sys/kernel/config/i3c_target/functions/tty/t/part_id
> > echo 0x6 > /sys/kernel/config/i3c_target/functions/tty/t/bcr
> >
> > ln -s /sys/kernel/config/i3c_target/functions/tty/t /sys/kernel/config/i3c_target/controllers/44330000.i3c-master/
> >
> > Then you echo test >/dev/ttySI3C0.
> >
> > Unlike USB, user can switch host and gadget mode dymatically. Suppose I3C
> > only work on one of master or slave mode only, which is static.
>
> I don't understand this. So it can switch dynamically or not?
I3C Protocal allow do that. But no one really do that.
>
> >
> > Although it is one hardware, I think it is exculsive multi function device.
>
> Just like serial engines. Do you see there replacing compatibles? No.
>
> >
> > Summary: basice two option to distingiush controller and target mode.
> > 1. by "compatible" string
> > 2. by "mode"
> >
> > I think 1 is relatively simple and easy to understand.
>
> Eh, if you only saw my comments on people replacing compatibles...
> Anyway, I stated my reasons, so to reiterate: NAK.
I know it. Needn't emphase it every time.
Is using "mode" ('controller' and 'target') proptery okay?
Frank
>
> Best regards,
> Krzysztof
>
