The patch adds display support on the stm32f769-disco board. Signed-off-by: Dario Binacchi <dario.binacchi@xxxxxxxxxxxxxxxxxxxx> --- Changes in v8: - Remove unit name from 'ltdc/port/endpoint@0' to fix the compiling warning: ../arch/arm/boot/dts/st/stm32f769-disco.dts:189.28-191.5: Warning (unit_address_vs_reg): /soc/display-controller@40016800/port/endpoint@0: node has a unit name, but no reg or ranges property arch/arm/boot/dts/st/stm32f769-disco.dts | 72 +++++++++++++++++++++++- 1 file changed, 71 insertions(+), 1 deletion(-) diff --git a/arch/arm/boot/dts/st/stm32f769-disco.dts b/arch/arm/boot/dts/st/stm32f769-disco.dts index 8632bd866272..b38eef824463 100644 --- a/arch/arm/boot/dts/st/stm32f769-disco.dts +++ b/arch/arm/boot/dts/st/stm32f769-disco.dts @@ -41,7 +41,7 @@ */ /dts-v1/; -#include "stm32f746.dtsi" +#include "stm32f769.dtsi" #include "stm32f769-pinctrl.dtsi" #include <dt-bindings/input/input.h> #include <dt-bindings/gpio/gpio.h> @@ -60,6 +60,19 @@ memory@c0000000 { reg = <0xC0000000 0x1000000>; }; + reserved-memory { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + linux,dma { + compatible = "shared-dma-pool"; + linux,dma-default; + no-map; + size = <0x100000>; + }; + }; + aliases { serial0 = &usart1; }; @@ -85,6 +98,13 @@ button-0 { }; }; + panel_backlight: panel-backlight { + compatible = "gpio-backlight"; + gpios = <&gpioi 14 GPIO_ACTIVE_HIGH>; + default-on; + status = "okay"; + }; + usbotg_hs_phy: usb-phy { #phy-cells = <0>; compatible = "usb-nop-xceiv"; @@ -114,6 +134,46 @@ &clk_hse { clock-frequency = <25000000>; }; +&dsi { + #address-cells = <1>; + #size-cells = <0>; + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + dsi_in: endpoint { + remote-endpoint = <<dc_out_dsi>; + }; + }; + + port@1 { + reg = <1>; + dsi_out: endpoint { + remote-endpoint = <&dsi_panel_in>; + }; + }; + }; + + panel0: panel-dsi@0 { + compatible = "orisetech,otm8009a"; + reg = <0>; /* dsi virtual channel (0..3) */ + reset-gpios = <&gpioj 15 GPIO_ACTIVE_LOW>; + power-supply = <&vcc_3v3>; + backlight = <&panel_backlight>; + status = "okay"; + + port { + dsi_panel_in: endpoint { + remote-endpoint = <&dsi_out>; + }; + }; + }; +}; + &i2c1 { pinctrl-0 = <&i2c1_pins_b>; pinctrl-names = "default"; @@ -122,6 +182,16 @@ &i2c1 { status = "okay"; }; +<dc { + status = "okay"; + + port { + ltdc_out_dsi: endpoint { + remote-endpoint = <&dsi_in>; + }; + }; +}; + &rtc { status = "okay"; }; -- 2.43.0