Re: [PATCH v4 0/3] Add support for LTC4282

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 09/01/2024 13:19, Nuno Sá wrote:
> On Mon, 2023-12-18 at 17:29 +0100, Nuno Sa wrote:
>> v1:
>>  *
>> https://lore.kernel.org/linux-hwmon/20231110151905.1659873-1-nuno.sa@xxxxxxxxxx/
>>
>> v2:
>>  *
>> https://lore.kernel.org/linux-hwmon/20231124-ltc4282-support-v2-0-952bf926f83c@xxxxxxxxxx
>>
>> v3:
>>  *
>> https://lore.kernel.org/r/20231205-ltc4282-support-v3-0-e0877b281bc2@xxxxxxxxxx
>>
>> Changes in v4:
>> - Patch 1:
>>  * New patch. Support fault attributes in voltage channels.
>> - Patch 2:
>>  * Add default values for gpios and divider properties;
>>  * Add adi,gpio3-monitor-enable property.
>> - Patch 3:
>>  - Docs:
>>   * Document that fault logs are also cleared when writing in reset_history
>>     attributes;
>>   * Document debugfs entries;
>>   * Add new in0_fault attributes and remove dropped ones.
>>  - Driver:
>>   * Add hwmon_in_fault attribute to report FET failures in VSOURCE;
>>   * Clear fault logs in reset_history;
>>   * Constify 'ltc4282_out_rates';
>>   * Add missing error check in ltc4282_cache_history();
>>   * Removed unused functions;
>>   * Renamed clk provider name so it's unique per device;
>>   * Support new adi,gpio3-monitor-enable property;
>>   * Dropped power1_good, fet_bad_fault, fet_short_fault, fault_logs_reset
>>     custom attributes. Note that only power1_good was really dropped.
>>     The other ones are supported in standard ABI.
>>   * Renamed debugfs directory for ltc4282-hwmonX;
>>   * Added in0 prefix to FET fault logs so it's clear they affect VSOURCE;
>>   * Fix in_range() condition (false means error);
>>   * Fix reset_history attributes. We should not write 0 in the lowest
>>     value. Write the theoretical max value in there. For vsource/vdd,
>>     also do it during device setup (or we would end up with 0).
>>   * Directly store the chip vdd instead of vin_mode in our device
>>     structure. Easier to handle reset_history;
>>   * Moved the vin_mode enum to reduce it's scope.
>>
>> As mentioned in v3 discussion, clearing the power bad fault log has no
>> effect but I'm still doing it for consistency and because we also allow
>> to read it in debugfs (so better allow to clear it as well)
>>
>> ---
>> Nuno Sa (3):
>>       dt-bindings: hwmon: Add LTC4282 bindings
>>       hwmon: add fault attribute for voltage channels
>>       hwmon: ltc4282: add support for the LTC4282 chip
>>
>>  Documentation/ABI/testing/sysfs-class-hwmon        |    9 +
>>  .../devicetree/bindings/hwmon/adi,ltc4282.yaml     |  159 ++
>>  Documentation/hwmon/index.rst                      |    1 +
>>  Documentation/hwmon/ltc4282.rst                    |  133 ++
>>  MAINTAINERS                                        |    8 +
>>  drivers/hwmon/Kconfig                              |   11 +
>>  drivers/hwmon/Makefile                             |    1 +
>>  drivers/hwmon/hwmon.c                              |    1 +
>>  drivers/hwmon/ltc4282.c                            | 1784
>> ++++++++++++++++++++
>>  include/linux/hwmon.h                              |    2 +
>>  10 files changed, 2109 insertions(+)
>>
>> Thanks!
>> - Nuno Sá
>>
> 
> Hi Guenter,
> 
> Just pinging this one. Not sure if you missed this one or just low priority in
> your queue :)

Merge window is open. Is it a critical fix? Does not look like, so don't
ping, it's pointless and only adds unnecessary traffic.

Best regards,
Krzysztof





[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux