Le 06/01/2024 à 11:14, Bhavin Sharma a écrit :
Adding support for stc3117 fuel gauge driver with
minimal functionality to read voltage level currently
Signed-off-by: Bhavin Sharma <bhavin.sharma-TXG9oGKWPboh9/7i5KS7/GGXanvQGlWp@xxxxxxxxxxxxxxxx>
---
Hi,
drivers/power/supply/Kconfig | 7 ++
drivers/power/supply/Makefile | 1 +
drivers/power/supply/stc3117_fuel_gauge.c | 136 ++++++++++++++++++++++
3 files changed, 144 insertions(+)
create mode 100644 drivers/power/supply/stc3117_fuel_gauge.c
diff --git a/drivers/power/supply/Kconfig b/drivers/power/supply/Kconfig
index f21cb05815ec..02df55b0d5f0 100644
--- a/drivers/power/supply/Kconfig
+++ b/drivers/power/supply/Kconfig
@@ -875,6 +875,13 @@ config FUEL_GAUGE_SC27XX
Say Y here to enable support for fuel gauge with SC27XX
PMIC chips.
+config FUEL_GAUGE_STC3117
+ tristate "STMicroelectronics STC3117 fuel gauge driver"
+ depends on I2C
+ help
+ Say Y here to enable support for fuel gauge with STC3117
+ PMIC chips.
+
config CHARGER_UCS1002
tristate "Microchip UCS1002 USB Port Power Controller"
depends on I2C
diff --git a/drivers/power/supply/Makefile b/drivers/power/supply/Makefile
index 58b567278034..f8ed3e5a8882 100644
--- a/drivers/power/supply/Makefile
+++ b/drivers/power/supply/Makefile
@@ -104,6 +104,7 @@ obj-$(CONFIG_CHARGER_CROS_USBPD) += cros_usbpd-charger.o
obj-$(CONFIG_CHARGER_CROS_PCHG) += cros_peripheral_charger.o
obj-$(CONFIG_CHARGER_SC2731) += sc2731_charger.o
obj-$(CONFIG_FUEL_GAUGE_SC27XX) += sc27xx_fuel_gauge.o
+obj-$(CONFIG_FUEL_GAUGE_STC3117) += stc3117_fuel_gauge.o
obj-$(CONFIG_CHARGER_UCS1002) += ucs1002_power.o
obj-$(CONFIG_CHARGER_BD99954) += bd99954-charger.o
obj-$(CONFIG_CHARGER_WILCO) += wilco-charger.o
diff --git a/drivers/power/supply/stc3117_fuel_gauge.c b/drivers/power/supply/stc3117_fuel_gauge.c
new file mode 100644
index 000000000000..bb033ac54858
--- /dev/null
+++ b/drivers/power/supply/stc3117_fuel_gauge.c
@@ -0,0 +1,136 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * stc3117_fuel_gauge.c - STMicroelectronics STC3117 Fuel Gauge Driver
+ *
+ * Copyright (c) 2024 Silicon Signals Pvt Ltd.
+ * Author: Bhavin Sharma <bhavin.sharma-TXG9oGKWPboh9/7i5KS7/GGXanvQGlWp@xxxxxxxxxxxxxxxx>
+ * Hardevsinh Palaniya <hardevsinh.palaniya-TXG9oGKWPbrc8hPZMNZi9dBPR1lH4CV8@xxxxxxxxxxxxxxxx>
+ */
+
+
Only 1 NL is enough.
+#include <linux/i2c.h>
+#include <linux/i2c-dev.h>
+#include <linux/kernel.h>
Is it really needed for a small driver like this?
+#include <linux/module.h>
+#include <linux/uaccess.h>
+#include <linux/power_supply.h>
Keep alphabetical order.
+
+#define VOLTAGE_REG_ADDR 0x08
+#define VOLTAGE_REG_ADDR_SIZE 1 //in bytes
+#define VOLTAGE_DATA_SIZE 2 //in bytes
+#define LSB_VALUE 2200 //in micro-volts
+
+
+static int stc3117_probe(struct i2c_client *client);
+static void stc3117_dev_remove(struct i2c_client *client);
If struct i2c_driver stc3117_i2c_driver was declared at the end of the
fine, these prototypes could be removed.
+
+static int stc3117_get_property(struct power_supply *psy,
+ enum power_supply_property psp, union power_supply_propval *val);
+static int stc3117_get_batt_volt(const struct i2c_client *client);
Same here.
I think that a different ordering could avoid these prototypes.
+
+const struct i2c_client *tmp_client;
+struct power_supply *stc_sply;
+
+static const struct of_device_id stc3117_of_match[] = {
+ { .compatible = "st,stc3117-fgu" },
+ {},
+};
+
+MODULE_DEVICE_TABLE(of, stc3117_of_match);
+
+static const struct i2c_device_id stc3117_id[] = {
+ {"stc3117", 0},
+ {},
+};
+
+
Only 1 NL is enough.
+MODULE_DEVICE_TABLE(i2c, stc3117_id);
+
+struct i2c_driver stc3117_i2c_driver = {
+ .driver = {
+ .name = "stc3117_i2c_driver",
+ .owner = THIS_MODULE,
+ .of_match_table = of_match_ptr(stc3117_of_match),
+ },
+ .probe = stc3117_probe,
+ .id_table = stc3117_id,
+ .remove = stc3117_dev_remove,
+};
+
+
Only 1 NL is enough.
+static enum power_supply_property stc3117_battery_props[] = {
+ POWER_SUPPLY_PROP_VOLTAGE_NOW,
+};
+
+static const struct power_supply_desc stc3117_battery_desc = {
+ .name = "stc3117-battery",
+ .type = POWER_SUPPLY_TYPE_BATTERY,
+ .get_property = stc3117_get_property,
+ .properties = stc3117_battery_props,
+ .num_properties = ARRAY_SIZE(stc3117_battery_props),
+};
+
+static int stc3117_get_property(struct power_supply *psy,
+ enum power_supply_property psp, union power_supply_propval *val)
+{
+ switch (psp) {
+ case POWER_SUPPLY_PROP_VOLTAGE_NOW:
+ val->intval = stc3117_get_batt_volt(tmp_client);
+ break;
This break should be indented by 1 more tab.
+ default:
+ return -EINVAL;
+ }
+ return 0;
+}
+
+
Only 1 NL is enough.
+static int stc3117_get_batt_volt(const struct i2c_client *stc_client)
+{
+ int ret, volt = 0;
+ char i2c_tx = VOLTAGE_REG_ADDR, i2c_rx[2] = {0};
Maybe VOLTAGE_DATA_SIZE, instead of 2?
+
+ ret = i2c_master_send(stc_client, &i2c_tx, VOLTAGE_REG_ADDR_SIZE);
+ if (ret > 0) {
+
+ ret = i2c_master_recv(stc_client, i2c_rx, VOLTAGE_DATA_SIZE);
+ if (ret > 0) {
+
+ volt = (i2c_rx[1] << 8) + i2c_rx[0];
+ volt *= LSB_VALUE;
+
+ return volt;
+ }
+ }
+
+ return ret;
+}
Writting it as:
ret = i2c_master_send()
if (ret < 0)
return ret;
ret = i2c_master_recv();
if (ret < 0)
return ret;
vols = ...
would save some indentation.
+
+static int stc3117_probe(struct i2c_client *client)
+{
+ struct power_supply_config psy_cfg = {};
+ struct device *dev;
+
+ dev = &client->dev;
+
+ psy_cfg.of_node = dev->of_node;
+
+ tmp_client = client;
+
+ stc_sply = power_supply_register(dev, &stc3117_battery_desc, &psy_cfg);
devm_power_supply_register() ?
This would remove the need of the .remove() function.
+ if (IS_ERR(stc_sply))
+ pr_err("failed to register battery\n");
dev_err()?
Maybe this error code should be propagated. What the point of this
driver if this function fails?
just my 2c,
CJ
+
+ return 0;
+}
+
+static void stc3117_dev_remove(struct i2c_client *client)
+{
+ power_supply_unregister(stc_sply);
+}
+
+module_i2c_driver(stc3117_i2c_driver);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Bhavin Sharma <bhavin.sharma-TXG9oGKWPboh9/7i5KS7/GGXanvQGlWp@xxxxxxxxxxxxxxxx>");
+MODULE_AUTHOR("Hardevsinh Palaniya <hardevsinh.palaniya-TXG9oGKWPboh9/7i5KS7/GGXanvQGlWp@xxxxxxxxxxxxxxxx>");
+MODULE_DESCRIPTION("STC3117 Fuel Gauge Driver");
+MODULE_VERSION("v1.0");
+
