Re: [RFC 2/9] arm64: dts: qcom: qrb5165-rb5: describe the WLAN module of QCA6390

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Thu, 4 Jan 2024 at 15:03, Bartosz Golaszewski <brgl@xxxxxxxx> wrote:
>
> From: Bartosz Golaszewski <bartosz.golaszewski@xxxxxxxxxx>
>
> Describe the ath11k WLAN on-board the QCA6390 module. Include the
> relevant regulators and the enable GPIO.
>
> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@xxxxxxxxxx>
> ---
>  arch/arm64/boot/dts/qcom/qrb5165-rb5.dts | 24 ++++++++++++++++++++++++
>  1 file changed, 24 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts
> index cd0db4f31d4a..721f86af952b 100644
> --- a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts
> +++ b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts
> @@ -734,6 +734,22 @@ &pcie0_phy {
>         vdda-pll-supply = <&vreg_l9a_1p2>;
>  };
>
> +&pcieport0 {
> +       wifi@0 {
> +               compatible = "pci17cb,1101";
> +               reg = <0x10000 0x0 0x0 0x0 0x0>;
> +
> +               pinctrl-names = "default";
> +               pinctrl-0 = <&wlan_en_state>;
> +
> +               enable-gpios = <&tlmm 20 GPIO_ACTIVE_HIGH>;
> +
> +               vddpmu-supply = <&vreg_s2f_0p95>;
> +               vddpcie1-supply = <&vreg_s8c_1p3>;
> +               vddpcie2-supply = <&vreg_s5a_1p9>;

If I remember correctly, qca6390 has at least 8 power supplies AON,
PMU, 3xRFA, 2xPCIe and VDDIO.

Moreover, these bindings do not solve another problem: the PMU is
shared between WiFi and BT parts. For the next gen (WCN6855) this
becomes even more important, see the code in msm-5.10 which makes sure
that there is a proper time between one of the units going down and
another one being powered on.

> +       };
> +};
> +
>  &pcie1 {
>         status = "okay";
>  };
> @@ -1303,6 +1319,14 @@ sdc2_card_det_n: sd-card-det-n-state {
>                 function = "gpio";
>                 bias-pull-up;
>         };
> +
> +       wlan_en_state: wlan-default-state {
> +               pins = "gpio20";
> +               function = "gpio";
> +               drive-strength = <16>;
> +               output-low;
> +               bias-pull-up;
> +       };
>  };
>
>  &uart6 {
> --
> 2.40.1
>
>


-- 
With best wishes
Dmitry




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux