On 12/20/23 11:33, Andy Yan wrote:
> From: Andy Yan <andy.yan@xxxxxxxxxxxxxx>
>
> When try to run rk3036 kylin board with mainline,
> I found the emac ethernet probe failed:
>
> [ 2.324583] loop: module loaded
> [ 2.328435] SPI driver spidev has no spi_device_id for rockchip,spidev
> [ 2.338688] tun: Universal TUN/TAP device driver, 1.6
> [ 2.345397] rockchip_emac 10200000.ethernet: no regulator found
> [ 2.351892] rockchip_emac 10200000.ethernet: ARC EMAC detected with id: 0x7fd02
> [ 2.359331] rockchip_emac 10200000.ethernet: IRQ is 43
> [ 2.364719] rockchip_emac 10200000.ethernet: MAC address is now e6:58:d6:ec:d9:7c
> [ 2.396993] mdio_bus Synopsys MII Bus: mdio has invalid PHY address
> [ 2.403306] mdio_bus Synopsys MII Bus: scan phy mdio at address 0
> [ 2.508656] rockchip_emac 10200000.ethernet: of_phy_connect() failed
> [ 2.516334] rockchip_emac 10200000.ethernet: failed to probe arc emac (-19)
>
> This reverts commit 1dabb74971b3 ("ARM: dts: rockchip: restyle emac nodes")
> make emac on rk3036 kylin board probe right again:
> [ 1.920385] CAN device driver interface
> [ 1.925499] rockchip_emac 10200000.ethernet: no regulator found
> [ 1.932535] rockchip_emac 10200000.ethernet: ARC EMAC detected with id: 0x7fd02
> [ 1.940735] rockchip_emac 10200000.ethernet: IRQ is 42
> [ 1.946743] rockchip_emac 10200000.ethernet: MAC address is now 96:7d:4f:0a:69:b3
> [ 2.581340] rockchip_emac 10200000.ethernet: connected to Generic PHY phy with id 0xffffc816
> [ 2.592560] e1000e: Intel(R) PRO/1000 Network Driver
> [ 2.598136] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
>
> Fixes: 1dabb74971b3 ("ARM: dts: rockchip: restyle emac nodes")
> Signed-off-by: Andy Yan <andy.yan@xxxxxxxxxxxxxx>
> ---
>
> arch/arm/boot/dts/rockchip/rk3036-evb.dts | 16 ++++++----------
> arch/arm/boot/dts/rockchip/rk3036-kylin.dts | 16 ++++++----------
> arch/arm/boot/dts/rockchip/rk3036.dtsi | 2 ++
> .../boot/dts/rockchip/rk3066a-marsboard.dts | 17 +++++++----------
> .../boot/dts/rockchip/rk3066a-rayeager.dts | 15 +++++----------
> .../boot/dts/rockchip/rk3188-radxarock.dts | 19 ++++++++-----------
> arch/arm/boot/dts/rockchip/rk3xxx.dtsi | 2 ++
> 7 files changed, 36 insertions(+), 51 deletions(-)
>
> diff --git a/arch/arm/boot/dts/rockchip/rk3036-evb.dts b/arch/arm/boot/dts/rockchip/rk3036-evb.dts
> index becdc0b664bf..94216f870b57 100644
> --- a/arch/arm/boot/dts/rockchip/rk3036-evb.dts
> +++ b/arch/arm/boot/dts/rockchip/rk3036-evb.dts
> @@ -15,20 +15,16 @@ memory@60000000 {
> };
>
> &emac {
> - phy = <&phy0>;
> - phy-reset-duration = <10>; /* millisecond */
> - phy-reset-gpios = <&gpio2 RK_PC6 GPIO_ACTIVE_LOW>; /* PHY_RST */
> pinctrl-names = "default";
> pinctrl-0 = <&emac_xfer>, <&emac_mdio>;
> - status = "okay";
> + phy = <&phy0>;
> + phy-reset-gpios = <&gpio2 RK_PC6 GPIO_ACTIVE_LOW>; /* PHY_RST */
> + phy-reset-duration = <10>; /* millisecond */
>
> - mdio {
> - #address-cells = <1>;
> - #size-cells = <0>;
> + status = "okay";
>
> - phy0: ethernet-phy@0 {
> - reg = <0>;
> - };
> + phy0: ethernet-phy@0 {
> + reg = <0>;
> };
Sorry, didn't have the hardware when changing that binding.
A little bit background info:
The rk3036 TRM states:
Management Interface (MDIO) state machine for easy real-time communication with the
PHY
A revert of the DT must also match a binding. But...
Bindings must describe the hardware as close as possible.
So when the phy is called over the mdio we must add phy as part of a mdio node.(Is that correct? Ask a expert!)
Somehow the old emac driver doesn't support this sub node setup.
First request would be have a look to make the driver work as it should.
Johan
> };
>
> diff --git a/arch/arm/boot/dts/rockchip/rk3036-kylin.dts b/arch/arm/boot/dts/rockchip/rk3036-kylin.dts
> index 67e1e04139e7..e817eba8c622 100644
> --- a/arch/arm/boot/dts/rockchip/rk3036-kylin.dts
> +++ b/arch/arm/boot/dts/rockchip/rk3036-kylin.dts
> @@ -80,20 +80,16 @@ &acodec {
> };
>
> &emac {
> - phy = <&phy0>;
> - phy-reset-duration = <10>; /* millisecond */
> - phy-reset-gpios = <&gpio2 RK_PC6 GPIO_ACTIVE_LOW>; /* PHY_RST */
> pinctrl-names = "default";
> pinctrl-0 = <&emac_xfer>, <&emac_mdio>;
> - status = "okay";
> + phy = <&phy0>;
> + phy-reset-gpios = <&gpio2 RK_PC6 GPIO_ACTIVE_LOW>; /* PHY_RST */
> + phy-reset-duration = <10>; /* millisecond */
>
> - mdio {
> - #address-cells = <1>;
> - #size-cells = <0>;
> + status = "okay";
>
> - phy0: ethernet-phy@0 {
> - reg = <0>;
> - };
> + phy0: ethernet-phy@0 {
> + reg = <0>;
> };
> };
>
> diff --git a/arch/arm/boot/dts/rockchip/rk3036.dtsi b/arch/arm/boot/dts/rockchip/rk3036.dtsi
> index 78686fc72ce6..e240b89b0b35 100644
> --- a/arch/arm/boot/dts/rockchip/rk3036.dtsi
> +++ b/arch/arm/boot/dts/rockchip/rk3036.dtsi
> @@ -228,6 +228,8 @@ emac: ethernet@10200000 {
> compatible = "rockchip,rk3036-emac";
> reg = <0x10200000 0x4000>;
> interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> rockchip,grf = <&grf>;
> clocks = <&cru HCLK_MAC>, <&cru SCLK_MACREF>, <&cru SCLK_MAC>;
> clock-names = "hclk", "macref", "macclk";
> diff --git a/arch/arm/boot/dts/rockchip/rk3066a-marsboard.dts b/arch/arm/boot/dts/rockchip/rk3066a-marsboard.dts
> index f6e8d49a02ef..e3d6f0e81330 100644
> --- a/arch/arm/boot/dts/rockchip/rk3066a-marsboard.dts
> +++ b/arch/arm/boot/dts/rockchip/rk3066a-marsboard.dts
> @@ -150,21 +150,18 @@ vcc28_cif: regulator@12 {
> #include "../tps65910.dtsi"
>
> &emac {
> + status = "okay";
> +
> phy = <&phy0>;
> phy-supply = <&vcc_rmii>;
> +
> pinctrl-names = "default";
> pinctrl-0 = <&emac_xfer>, <&emac_mdio>, <&phy_int>;
> - status = "okay";
> -
> - mdio {
> - #address-cells = <1>;
> - #size-cells = <0>;
>
> - phy0: ethernet-phy@0 {
> - reg = <0>;
> - interrupt-parent = <&gpio1>;
> - interrupts = <RK_PD2 IRQ_TYPE_LEVEL_LOW>;
> - };
> + phy0: ethernet-phy@0 {
> + reg = <0>;
> + interrupt-parent = <&gpio1>;
> + interrupts = <RK_PD2 IRQ_TYPE_LEVEL_LOW>;
> };
> };
>
> diff --git a/arch/arm/boot/dts/rockchip/rk3066a-rayeager.dts b/arch/arm/boot/dts/rockchip/rk3066a-rayeager.dts
> index 29d8e5bf88f5..096616324c2d 100644
> --- a/arch/arm/boot/dts/rockchip/rk3066a-rayeager.dts
> +++ b/arch/arm/boot/dts/rockchip/rk3066a-rayeager.dts
> @@ -142,20 +142,15 @@ &cpu1 {
> };
>
> &emac {
> - phy = <&phy0>;
> - phy-supply = <&vcc_rmii>;
> pinctrl-names = "default";
> pinctrl-0 = <&emac_xfer>, <&emac_mdio>, <&rmii_rst>;
> + phy = <&phy0>;
> + phy-supply = <&vcc_rmii>;
> status = "okay";
>
> - mdio {
> - #address-cells = <1>;
> - #size-cells = <0>;
> -
> - phy0: ethernet-phy@0 {
> - reg = <0>;
> - reset-gpios = <&gpio1 RK_PD6 GPIO_ACTIVE_LOW>;
> - };
> + phy0: ethernet-phy@0 {
> + reg = <0>;
> + reset-gpios = <&gpio1 RK_PD6 GPIO_ACTIVE_LOW>;
> };
> };
>
> diff --git a/arch/arm/boot/dts/rockchip/rk3188-radxarock.dts b/arch/arm/boot/dts/rockchip/rk3188-radxarock.dts
> index 118deacd38c4..239d2ec37fdc 100644
> --- a/arch/arm/boot/dts/rockchip/rk3188-radxarock.dts
> +++ b/arch/arm/boot/dts/rockchip/rk3188-radxarock.dts
> @@ -126,21 +126,18 @@ vsys: vsys-regulator {
> };
>
> &emac {
> - phy = <&phy0>;
> - phy-supply = <&vcc_rmii>;
> + status = "okay";
> +
> pinctrl-names = "default";
> pinctrl-0 = <&emac_xfer>, <&emac_mdio>, <&phy_int>;
> - status = "okay";
>
> - mdio {
> - #address-cells = <1>;
> - #size-cells = <0>;
> + phy = <&phy0>;
> + phy-supply = <&vcc_rmii>;
>
> - phy0: ethernet-phy@0 {
> - reg = <0>;
> - interrupt-parent = <&gpio3>;
> - interrupts = <RK_PD2 IRQ_TYPE_LEVEL_LOW>;
> - };
> + phy0: ethernet-phy@0 {
> + reg = <0>;
> + interrupt-parent = <&gpio3>;
> + interrupts = <RK_PD2 IRQ_TYPE_LEVEL_LOW>;
> };
> };
>
> diff --git a/arch/arm/boot/dts/rockchip/rk3xxx.dtsi b/arch/arm/boot/dts/rockchip/rk3xxx.dtsi
> index cb4e42ede56a..17e89d30de78 100644
> --- a/arch/arm/boot/dts/rockchip/rk3xxx.dtsi
> +++ b/arch/arm/boot/dts/rockchip/rk3xxx.dtsi
> @@ -193,6 +193,8 @@ emac: ethernet@10204000 {
> compatible = "snps,arc-emac";
> reg = <0x10204000 0x3c>;
> interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
> + #address-cells = <1>;
> + #size-cells = <0>;
>
> rockchip,grf = <&grf>;
>
