Add the necessary nodes to support the USB-C Altmode path by adding the following - WCD939x USBSS Mux I2C device - nb7vpq904m Redriver I2C device - Port/Endpoint graph links bettween PMIC-Glink, Mux, Redriver and USB PHY nodes. WCD939x USBSS port 2 Path to Codec will be added later when Audio support is added. Signed-off-by: Neil Armstrong <neil.armstrong@xxxxxxxxxx> --- arch/arm64/boot/dts/qcom/sm8650-qrd.dts | 104 +++++++++++++++++++++++++++++++- 1 file changed, 102 insertions(+), 2 deletions(-) diff --git a/arch/arm64/boot/dts/qcom/sm8650-qrd.dts b/arch/arm64/boot/dts/qcom/sm8650-qrd.dts index 592a67a47c78..121fbbb5d015 100644 --- a/arch/arm64/boot/dts/qcom/sm8650-qrd.dts +++ b/arch/arm64/boot/dts/qcom/sm8650-qrd.dts @@ -77,9 +77,17 @@ port@1 { reg = <1>; pmic_glink_ss_in: endpoint { - remote-endpoint = <&usb_1_dwc3_ss>; + remote-endpoint = <&redriver_ss_out>; }; }; + + port@2 { + reg = <2>; + + pmic_glink_sbu: endpoint { + remote-endpoint = <&wcd_usbss_sbu_mux>; + }; + }; }; }; }; @@ -446,6 +454,70 @@ &gpi_dma1 { status = "okay"; }; +&i2c3 { + status = "ok"; + + wcd_usbss: typec-mux@e { + compatible = "qcom,wcd9395-usbss", "qcom,wcd9390-usbss"; + reg = <0xe>; + + vdd-supply = <&vreg_l15b_1p8>; + reset-gpios = <&tlmm 152 GPIO_ACTIVE_HIGH>; + + mode-switch; + orientation-switch; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + wcd_usbss_sbu_mux: endpoint { + remote-endpoint = <&pmic_glink_sbu>; + }; + }; + }; + }; +}; + +&i2c6 { + status = "ok"; + + typec-mux@1c { + compatible = "onnn,nb7vpq904m"; + reg = <0x1c>; + + vcc-supply = <&vreg_l15b_1p8>; + + retimer-switch; + orientation-switch; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + redriver_ss_out: endpoint { + remote-endpoint = <&pmic_glink_ss_in>; + }; + }; + + port@1 { + reg = <1>; + + redriver_ss_in: endpoint { + data-lanes = <3 2 1 0>; + remote-endpoint = <&usb_dp_qmpphy_out>; + }; + }; + }; + }; +}; + &ipa { qcom,gsi-loader = "self"; memory-region = <&ipa_fw_mem>; @@ -495,6 +567,15 @@ &mdss_dsi0_phy { status = "okay"; }; +&mdss_dp0 { + status = "okay"; +}; + +&mdss_dp0_out { + data-lanes = <0 1>; + remote-endpoint = <&usb_dp_qmpphy_dp_in>; +}; + &mdss_mdp { status = "okay"; }; @@ -600,6 +681,11 @@ &pmk8550_rtc { status = "okay"; }; +&qup_i2c3_data_clk { + /* Use internal I2C pull-up */ + bias-pull-up = <2200>; +}; + &qupv3_id_0 { status = "okay"; }; @@ -787,7 +873,7 @@ &usb_1_dwc3_hs { }; &usb_1_dwc3_ss { - remote-endpoint = <&pmic_glink_ss_in>; + remote-endpoint = <&usb_dp_qmpphy_usb_ss_in>; }; &usb_1_hsphy { @@ -803,9 +889,23 @@ &usb_dp_qmpphy { vdda-phy-supply = <&vreg_l3i_1p2>; vdda-pll-supply = <&vreg_l3g_0p91>; + orientation-switch; + status = "okay"; }; +&usb_dp_qmpphy_dp_in { + remote-endpoint = <&mdss_dp0_out>; +}; + +&usb_dp_qmpphy_out { + remote-endpoint = <&redriver_ss_in>; +}; + +&usb_dp_qmpphy_usb_ss_in { + remote-endpoint = <&usb_1_dwc3_ss>; +}; + &xo_board { clock-frequency = <76800000>; }; -- 2.34.1