> Yes, Russell, i will add an example in the DT doc in the next patch set. > The following is the device node used for the current qca8084 PHY > code design. If you look at Christians work, this would be expressed differently: > mdio: mdio@90000 { > ethernet-phy-package@1 { > > compatible = "qca,qca8084-package"; > > qcom,phy-work-mode = <2>; > clocks = <&qca8k_nsscc NSS_CC_APB_BRIDGE_CLK>, > <&qca8k_nsscc NSS_CC_AHB_CLK>, > <&qca8k_nsscc NSS_CC_SEC_CTRL_AHB_CLK>, > <&qca8k_nsscc NSS_CC_TLMM_CLK>, > <&qca8k_nsscc NSS_CC_TLMM_AHB_CLK>, > <&qca8k_nsscc NSS_CC_CNOC_AHB_CLK>, > <&qca8k_nsscc NSS_CC_MDIO_AHB_CLK>, > <&qca8k_nsscc NSS_CC_MDIO_MASTER_AHB_CLK>, > <&qca8k_nsscc NSS_CC_SRDS0_SYS_CLK>, > <&qca8k_nsscc NSS_CC_SRDS1_SYS_CLK>; > clock-names = "apb_bridge", > "ahb", > "sec_ctrl_ahb", > "tlmm", > "tlmm_ahb", > "cnoc_ahb", > "mdio_ahb", > "mdio_master_ahb", > "srds0_sys", > "srds1_sys"; > resets = <&qca8k_nsscc NSS_CC_SRDS0_SYS_ARES>, > <&qca8k_nsscc NSS_CC_SRDS1_SYS_ARES>, > <&qca8k_nsscc NSS_CC_DSP_ARES>; > reset-names = "srds0_sys", > "srds1_sys"; > All the properties above are common to the package as a whole. Then follow the four individual PHYs, and the properties which are specific to each one. > > ethernet-phy@0 { > compatible = "ethernet-phy-id004d.d180"; > reg = <0>; > clocks = <qca8k_nsscc NSS_CC_GEPHY0_SYS_CLK>, > clock-names = <"gephy_sys">; > resets = <&qca8k_nsscc NSS_CC_GEPHY0_SYS_ARES>, > <&qca8k_nsscc NSS_CC_GEPHY0_ARES>; > reset-names = "gephy_sys", "gephy_soft"; > }; > > > ethernet-phy@1 { > compatible = "ethernet-phy-id004d.d180"; > reg = <1>; > clocks = <qca8k_nsscc NSS_CC_GEPHY1_SYS_CLK>, > clock-names = <"gephy_sys">; > resets = <&qca8k_nsscc NSS_CC_GEPHY1_SYS_ARES>, > <&qca8k_nsscc NSS_CC_GEPHY1_ARES>; > reset-names = "gephy_sys", "gephy_soft"; > > }; > > ethernet-phy@2 { > compatible = "ethernet-phy-id004d.d180"; > reg = <2>; > clocks = <qca8k_nsscc NSS_CC_GEPHY2_SYS_CLK>, > clock-names = <"gephy_sys">; > resets = <&qca8k_nsscc NSS_CC_GEPHY2_SYS_ARES>, > <&qca8k_nsscc NSS_CC_GEPHY2_ARES>; > reset-names = "gephy_sys", "gephy_soft"; > > }; > > ethernet-phy@3 { > compatible = "ethernet-phy-id004d.d180"; > reg = <3>; > clocks = <qca8k_nsscc NSS_CC_GEPHY3_SYS_CLK>, > clock-names = <"gephy_sys">; > reset-names = "gephy_sys", "gephy_soft"; > }; > }; Andrew