[PATCH 1/2] remoteproc: microblaze: Document device tree bindings

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




Add device tree binding documentation for the Microblaze remoteproc
on Xilinx Zynq.

Signed-off-by: Michal Simek <michal.simek@xxxxxxxxxx>
---

 .../bindings/remoteproc/mb_remoteproc.txt          | 46 ++++++++++++++++++++++
 1 file changed, 46 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/remoteproc/mb_remoteproc.txt

diff --git a/Documentation/devicetree/bindings/remoteproc/mb_remoteproc.txt b/Documentation/devicetree/bindings/remoteproc/mb_remoteproc.txt
new file mode 100644
index 000000000000..a2490eac0208
--- /dev/null
+++ b/Documentation/devicetree/bindings/remoteproc/mb_remoteproc.txt
@@ -0,0 +1,46 @@
+Xilinx ARM-Microblaze remoteproc driver
+
+This driver requires specific Zynq hardware design where Microblaze is added
+to the programmable logic.
+Microblaze is connected with PS block via axi bus connected to PS HP port
+to ensure access to PS DDR.
+Communication channels are done via soft GPIO IP connected to PS block
+and to Microblaze. There are also 2 gpio control signals reset and debug
+which are used for resetting Microblaze.
+
+Required properties:
+- compatible : Should be "xlnx,mb_remoteproc"
+- reg : Address and length of the ddr address space
+- bram: Phandle to bram controller which can access Microblaze BRAM
+- bram-firmware : Microblaze BRAM bootloader name
+- firmware : Default firmware name which can be override by
+	     "firmware" module parameter
+- reset : Gpio phandle which reset Microblaze remoteproc
+- debug : Gpio phandle which setup Microblaze to debug state
+- ipino : Gpio phandle for Microblaze to ARM communication
+- vring0 : Gpio phandle for ARM to Microblaze communication vring 0
+- vring1 : Gpio phandle for ARM to Microblaze communication vring 1
+
+Microblaze SoC can be also connected to the PS block via a axi bus.
+That's why there is the option to allocate interrupts for Microblaze use only.
+The driver will allocate interrupts to itself and Microblaze sw has to ensure
+that interrupts are properly enabled and handled by Microblaze interrupt
+controller.
+
+Optional properties:
+ - interrupts : Interrupt mapping for remoteproc
+ - interrupt-parent : Phandle for the interrupt controller
+
+Example:
+mb_remoteproc@800000 {
+	compatible = "xlnx,mb_remoteproc";
+	reg = < 0x8000000 0x8000000 >;
+	bram = <&axi_bram_ctrl_0>;
+	bram-firmware = "mb.bin";
+	firmware = "image.elf";
+	reset = <&zynq_gpio_reset 1 0>;
+	debug = <&zynq_gpio_reset 0 0>;
+	ipino = <&zynq_gpio_vring 0 0>;
+	vring0 = <&zynq_gpio_vring 1 0>;
+	vring1 = <&zynq_gpio_vring 2 0>;
+};
--
1.8.2.3

Attachment: pgpyA33eJfUnJ.pgp
Description: PGP signature


[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]
  Powered by Linux