Hi Thanks for the patch. Few comments On 14/12/23 03:02, Sukrut Bellary wrote: > BeaglePlay SBC has Texas Instrument's WL18xx WiFi Chipset. > > BeaglePlay SBC: > https://www.beagleboard.org/boards/beagleplay > > TI WL18XX: > https://www.ti.com/lit/ds/symlink/wl1807mod.pdf > > Currently, WLAN_EN is configured as regulator and regulator-always-on. > During hibernation thaw, WiFi fails to come online. > During freeze/suspend, > the WLAN_EN line is not put to low '0' to power down the WiFi. > So during restore, the WiFi driver tries to load the FW without following > correct power sequence. > WLAN_EN => '1'/assert (high) to power-up the chipset. > WLAN_EN => '0'/deassert (low) to shut-down the chipset. > > thaw failure log below: > > Use mmc-pwrseq-simple to drive TI's WiFi (WL18xx) chipset enable 'WLAN_EN'. > mmc-pwrseq-simple provides power sequence flexibility with support for > post power-on and power-off delays. > > ================ thaw failure Log ================ > [ 161.418528] ------------[ cut here ]------------ > [ 161.418540] WARNING: CPU: 1 PID: 45 at drivers/net/wireless/ti/wlcore/sdio.c:123 wl12xx_sdio_raw_write+0xe4/0x168 [wlcore_sdio] Adding full stack dump is usually noise. This line alone should be sufficient to point to the location of dump. Besides you have the link to the full log for anyone looking for more details > [ 161.418576] Modules linked in: br_netfilter bridge stp llc overlay usb_f_mass_storage usb_f_acm u_serial usb_f_ncm usb_f_rndis u_ether libcomposite wl18xx wlcore mac80211 libarc4 cfg80211 rfkill crct10dif_ce6[ 161.418676] CPU: 1 PID: 45 Comm: kworker/u8:2 Not tainted 6.5.0-rc6+ #2 > [ 161.418684] Hardware name: BeagleBoard.org BeaglePlay (DT) > [ 161.418691] Workqueue: events_unbound async_run_entry_fn > [ 161.418711] pstate: 20000005 (nzCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) > [ 161.418719] pc : wl12xx_sdio_raw_write+0xe4/0x168 [wlcore_sdio] > [ 161.418731] lr : wl12xx_sdio_raw_write+0x94/0x168 [wlcore_sdio] > [ 161.418743] sp : ffff800082b43970 > [ 161.418746] x29: ffff800082b43970 x28: ffff800083c5b000 x27: 0000000000000003 > [ 161.418757] x26: ffff80007aab3800 x25: ffff800083c53000 x24: 0000000000000000 > [ 161.418767] x23: 0000000000004000 x22: ffff00000f938000 x21: ffff000005bd3010 > [ 161.418778] x20: 0000000000008000 x19: ffff000005bd2000 x18: 0000000000000000 > [ 161.418789] x17: 0000000000000100 x16: 0000000000000000 x15: f44fb9a9e0200014 > [ 161.418799] x14: 0000000000000049 x13: 000000000000038f x12: 0000000000000000 > [ 161.418809] x11: 0000000000000001 x10: 0000000000000a50 x9 : ffff800082b43550 > [ 161.418819] x8 : ffff000000ca2830 x7 : ffff00007fb92f40 x6 : 00000007e5428bd2 > [ 161.418829] x5 : 03ffffffffffffff x4 : ffff0000002569c0 x3 : 0000000000000000 > [ 161.418839] x2 : 0000000000000001 x1 : ffff000000256810 x0 : 00000000ffffff92 > [ 161.418850] Call trace: > [ 161.418856] wl12xx_sdio_raw_write+0xe4/0x168 [wlcore_sdio] > [ 161.418869] wlcore_raw_write.constprop.0+0x4c/0xac [wlcore] > [ 161.418931] wlcore_boot_upload_firmware+0x140/0x3c0 [wlcore] > [ 161.418973] wl18xx_boot+0x574/0x77c [wl18xx] > [ 161.419011] wl1271_op_add_interface+0x5f0/0xaa8 [wlcore] > [ 161.419052] drv_add_interface+0x3c/0x88 [mac80211] > [ 161.419228] ieee80211_reconfig+0x1a8/0xf1c [mac80211] > [ 161.419330] ieee80211_resume+0x54/0x70 [mac80211] > [ 161.419432] wiphy_resume+0x84/0xf8 [cfg80211] > [ 161.419562] device_resume+0x84/0x178 > [ 161.419576] async_resume+0x28/0x74 > [ 161.419584] async_run_entry_fn+0x34/0xe0 > [ 161.419596] process_one_work+0x1e0/0x340 > [ 161.419605] worker_thread+0x68/0x428 > [ 161.419613] kthread+0x114/0x118 > [ 161.419620] ret_from_fork+0x10/0x20 > [ 161.419630] ---[ end trace 0000000000000000 ]--- > [ 161.419726] wl1271_sdio mmc2:0001:2: sdio write failed (-110) > [ 162.341981] wlcore: using inverted interrupt logic: 2 > [ 170.553515] ------------[ cut here ]------------ > > [ 180.315942] ieee80211 phy0: PM: dpm_run_callback(): wiphy_resume+0x0/0xf8 [cfg80211] returns -110 > [ 180.316090] ieee80211 phy0: PM: failed to thaw async: error -110 > ====================================================== > > Full thaw failure log - > https://gist.github.com/sukrutb/8b02a9ffa7bd1cb9fb514220e9af097e > > Suggested-by: Shengyu Qu <wiagn233@xxxxxxxxxxx> > Signed-off-by: Sukrut Bellary <sukrut.bellary@xxxxxxxxx> > --- > .../arm64/boot/dts/ti/k3-am625-beagleplay.dts | 25 ++++++++----------- > 1 file changed, 10 insertions(+), 15 deletions(-) > > diff --git a/arch/arm64/boot/dts/ti/k3-am625-beagleplay.dts b/arch/arm64/boot/dts/ti/k3-am625-beagleplay.dts > index eadbdd9ffe37..d388c5e78658 100644 > --- a/arch/arm64/boot/dts/ti/k3-am625-beagleplay.dts > +++ b/arch/arm64/boot/dts/ti/k3-am625-beagleplay.dts > @@ -83,6 +83,15 @@ wkup_r5fss0_core0_dma_memory_region: r5f-dma-memory@9db00000 { > }; > }; > > + sdio_pwrseq: sdio-pwrseq { > + compatible = "mmc-pwrseq-simple"; > + pinctrl-names = "default"; > + pinctrl-0 = <&wifi_en_pins_default>; > + post-power-on-delay-ms = <1>; > + power-off-delay-us = <80>; how did you arrive at these delay's. A comment to that order would be good to add. > + reset-gpios = <&main_gpio0 38 GPIO_ACTIVE_LOW>; > + }; > + > vsys_5v0: regulator-1 { > bootph-all; > compatible = "regulator-fixed"; > @@ -105,20 +114,6 @@ vdd_3v3: regulator-2 { > regulator-boot-on; > }; > > - wlan_en: regulator-3 { > - /* OUTPUT of SN74AVC2T244DQMR */ > - compatible = "regulator-fixed"; > - regulator-name = "wlan_en"; > - regulator-min-microvolt = <1800000>; > - regulator-max-microvolt = <1800000>; > - enable-active-high; > - regulator-always-on; > - vin-supply = <&vdd_3v3>; > - gpio = <&main_gpio0 38 GPIO_ACTIVE_HIGH>; > - pinctrl-names = "default"; > - pinctrl-0 = <&wifi_en_pins_default>; > - }; > - > vdd_3v3_sd: regulator-4 { > /* output of TPS22918DBVR-U21 */ > bootph-all; > @@ -849,7 +844,6 @@ &sdhci1 { > }; > > &sdhci2 { > - vmmc-supply = <&wlan_en>; > pinctrl-names = "default"; > pinctrl-0 = <&wifi_pins_default>, <&wifi_32k_clk>; > bus-width = <4>; > @@ -857,6 +851,7 @@ &sdhci2 { > ti,fails-without-test-cd; > cap-power-off-card; > keep-power-in-suspend; > + mmc-pwrseq = <&sdio_pwrseq>; > ti,driver-strength-ohm = <50>; > assigned-clocks = <&k3_clks 157 158>; > assigned-clock-parents = <&k3_clks 157 160>; -- Regards Vignesh
