Enable interrupt mode of operation of the DP83867 Ethernet PHY which is used by ICSSG2. The DP83867 PHY driver already supports interrupt handling for interrupts generated by the PHY. Thus, add the necessary device-tree support to enable it. Since the GPIO1_87 line is muxed with EXT_REFCLK1 and SYNC1_OUT, update the pinmux to select GPIO1_87 for routing the interrupt. As the same interrupt line and therefore the same pinmux configuration is applicable to both Ethernet PHYs used by ICSSG2, allocate the pinmux resource to the first Ethernet PHY alone. Signed-off-by: Siddharth Vadapalli <s-vadapalli@xxxxxx> Reviewed-by: MD Danish Anwar <danishanwar@xxxxxx> --- Hello, This patch is based on linux-next tagged next-20231213. v1: https://lore.kernel.org/r/20231120063159.539306-1-s-vadapalli@xxxxxx/ Changes since v1: - Rebased patch on next-20231213. - Collected Reviewed-by tag from MD Danish Anwar <danishanwar@xxxxxx> - Moved pinctrl from MDIO node to Ethernet PHY node based on feedback from Nishanth Menon <nm@xxxxxx> - Replaced the hard-coded value 0x2 with IRQ_TYPE_EDGE_FALLING for setting the interrupt trigger type and level flag based on feedback from Nishanth Menon <nm@xxxxxx> - Included dt-bindings/interrupt-controller/irq.h in the overlay. - Updated commit message with details of the pinmux resource allocation. Regards, Siddharth. arch/arm64/boot/dts/ti/k3-am654-icssg2.dtso | 17 +++++++++++++++++ 1 file changed, 17 insertions(+) diff --git a/arch/arm64/boot/dts/ti/k3-am654-icssg2.dtso b/arch/arm64/boot/dts/ti/k3-am654-icssg2.dtso index ec8cf20ca3ac..6eabdfa0d602 100644 --- a/arch/arm64/boot/dts/ti/k3-am654-icssg2.dtso +++ b/arch/arm64/boot/dts/ti/k3-am654-icssg2.dtso @@ -8,6 +8,7 @@ /dts-v1/; /plugin/; +#include <dt-bindings/interrupt-controller/irq.h> #include <dt-bindings/net/ti-dp83867.h> #include "k3-pinctrl.h" @@ -124,6 +125,15 @@ AM65X_IOPAD(0x0088, PIN_INPUT, 2) /* (AG17) PRG2_PRU0_GPO4.PRG2_RGMII1_RX_CTL */ }; }; +&main_pmx1 { + /* Select GPIO1_87 for ICSSG2 PHY interrupt */ + icssg2_phy_irq_pins_default: icssg2-phy-irq-default-pins { + pinctrl-single,pins = < + AM65X_IOPAD(0x0014, PIN_INPUT, 7) /* (A22) EXT_REFCLK1.GPIO1_87 */ + >; + }; +}; + &icssg2_mdio { status = "okay"; pinctrl-names = "default"; @@ -132,13 +142,20 @@ &icssg2_mdio { #size-cells = <0>; icssg2_phy0: ethernet-phy@0 { + pinctrl-names = "default"; + pinctrl-0 = <&icssg2_phy_irq_pins_default>; + reg = <0>; + interrupt-parent = <&main_gpio1>; + interrupts = <87 IRQ_TYPE_EDGE_FALLING>; ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>; ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>; }; icssg2_phy1: ethernet-phy@3 { reg = <3>; + interrupt-parent = <&main_gpio1>; + interrupts = <87 IRQ_TYPE_EDGE_FALLING>; ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>; ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>; }; -- 2.34.1
