On 11/12/2023 06:47, Delphine CC Chiu wrote:
> Revise i2c11 and i2c12 schematic change:
> - remove space for adm1272 compatible
> - enable interrupt setting for pca9555
> - add eeprom for yosemite4 medusa board/BSM use
> - remove temperature sensor for yosemite4 schematic change
> - add power sensor for power module reading
Way too many changes in one patch. Especially mixing fixes and new
features is bad. Please don't.
>
> Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@xxxxxxxxxx>
> ---
> .../aspeed/aspeed-bmc-facebook-yosemite4.dts | 118 ++++++++++++++----
> 1 file changed, 93 insertions(+), 25 deletions(-)
>
> diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
> index da413325ce30..ccb5ecd8d9a6 100644
> --- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
> +++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
> @@ -821,41 +821,94 @@ imux29: i2c@1 {
> &i2c11 {
> status = "okay";
> power-sensor@10 {
> - compatible = "adi, adm1272";
> + compatible = "adi,adm1272";
> reg = <0x10>;
> };
>
> power-sensor@12 {
> - compatible = "adi, adm1272";
> + compatible = "adi,adm1272";
> reg = <0x12>;
> };
>
> - gpio@20 {
> + gpio_ext1: pca9555@20 {
That's wrong name.
> compatible = "nxp,pca9555";
> - reg = <0x20>;
> + pinctrl-names = "default";
> gpio-controller;
> #gpio-cells = <2>;
> - };
> -
> - gpio@21 {
> + reg = <0x20>;
> + interrupt-parent = <&gpio0>;
> + interrupts = <94 IRQ_TYPE_LEVEL_LOW>;
> + gpio-line-names =
> + "P48V_OCP_GPIO1","P48V_OCP_GPIO2",
> + "P48V_OCP_GPIO3","FAN_BOARD_0_REVISION_0_R",
> + "FAN_BOARD_0_REVISION_1_R","FAN_BOARD_1_REVISION_0_R",
> + "FAN_BOARD_1_REVISION_1_R","RST_MUX_R_N",
> + "RST_LED_CONTROL_FAN_BOARD_0_N","RST_LED_CONTROL_FAN_BOARD_1_N",
> + "RST_IOEXP_FAN_BOARD_0_N","RST_IOEXP_FAN_BOARD_1_N",
> + "PWRGD_LOAD_SWITCH_FAN_BOARD_0_R","PWRGD_LOAD_SWITCH_FAN_BOARD_1_R",
> + "","";
> + };
> +
> + gpio_ext2: pca9555@21 {
Node names should be generic. See also an explanation and list of
examples (not exhaustive) in DT specification:
https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation
> compatible = "nxp,pca9555";
> - reg = <0x21>;
> + pinctrl-names = "default";
> gpio-controller;
> #gpio-cells = <2>;
> - };
> -
> - gpio@22 {
> + reg = <0x21>;
> + interrupt-parent = <&gpio0>;
> + interrupts = <94 IRQ_TYPE_LEVEL_LOW>;
> + gpio-line-names =
> + "DELTA_MODULE_TYPE","VSENSE_ERR_VDROP_R",
> + "EN_P48V_AUX_0","EN_P48V_AUX_1",
> + "MEDUSA_BOARD_REV_0","MEDUSA_BOARD_REV_1",
> + "MEDUSA_BOARD_REV_2","MEDUSA_BOARD_TYPE",
> + "HSC_OCP_SLOT_ODD_GPIO1","HSC_OCP_SLOT_ODD_GPIO2",
> + "HSC_OCP_SLOT_ODD_GPIO3","HSC_OCP_SLOT_EVEN_GPIO1",
> + "HSC_OCP_SLOT_EVEN_GPIO2","HSC_OCP_SLOT_EVEN_GPIO3",
> + "ADC_TYPE_0_R","ADC_TYPE_1_R";
> + };
> +
> + gpio_ext3: pca9555@22 {
Please fix it everywhere.
In this patch and all your future patches. I keep repeating the same
feedback...
Best regards,
Krzysztof
