On 06.12.23 04:01, Shawn Guo wrote:
> On Thu, Nov 30, 2023 at 05:16:14PM +0100, Frieder Schrempf wrote:
>> From: Frieder Schrempf <frieder.schrempf@xxxxxxxxxx>
>>
>> The OSM spec defines dedicated functions for all pads of the SoM.
>> Therefore we can assume that carrier board designs stick to these
>> definitions and extend the SoM devicetree include with matching
>> default nodes and pinmux settings.
>>
>> This way we can reduce the overhead and redundancy in the carrier
>> board devicetrees while still sticking to the policy of separating
>> board and module description.
>>
>> Even if the carrier board design deviates slightly from the spec it
>> can define its own pinmux definitions and use them as necessary or
>> even disable unused nodes from the SoM devicetree.
>>
>> Signed-off-by: Frieder Schrempf <frieder.schrempf@xxxxxxxxxx>
>> ---
>> Changes for v2:
>> * none
>> ---
>> .../dts/freescale/imx8mm-kontron-bl-osm-s.dts | 269 +++------
>> .../dts/freescale/imx8mm-kontron-osm-s.dtsi | 552 +++++++++++++++++-
>> 2 files changed, 616 insertions(+), 205 deletions(-)
>>
>> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts
>> index 12f786a72fbd5..efadfdff00af1 100644
>> --- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts
>> +++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts
>> @@ -25,8 +25,6 @@ osc_can: clock-osc-can {
>>
>> leds {
>> compatible = "gpio-leds";
>> - pinctrl-names = "default";
>> - pinctrl-0 = <&pinctrl_gpio_led>;
>>
>> led1 {
>> label = "led1";
>> @@ -52,24 +50,12 @@ pwm-beeper {
>>
>> reg_rst_eth2: regulator-rst-eth2 {
>> compatible = "regulator-fixed";
>> - pinctrl-names = "default";
>> - pinctrl-0 = <&pinctrl_usb_eth2>;
>> gpio = <&gpio1 1 GPIO_ACTIVE_HIGH>;
>> enable-active-high;
>> regulator-always-on;
>> regulator-name = "rst-usb-eth2";
>> };
>>
>> - reg_usb1_vbus: regulator-usb1-vbus {
>> - compatible = "regulator-fixed";
>> - pinctrl-names = "default";
>> - pinctrl-0 = <&pinctrl_reg_usb1_vbus>;
>> - gpio = <&gpio3 25 GPIO_ACTIVE_LOW>;
>> - regulator-min-microvolt = <5000000>;
>> - regulator-max-microvolt = <5000000>;
>> - regulator-name = "usb1-vbus";
>> - };
>> -
>> reg_vdd_5v: regulator-5v {
>> compatible = "regulator-fixed";
>> regulator-always-on;
>> @@ -80,9 +66,6 @@ reg_vdd_5v: regulator-5v {
>> };
>>
>> &ecspi2 {
>> - pinctrl-names = "default";
>> - pinctrl-0 = <&pinctrl_ecspi2>;
>> - cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
>> status = "okay";
>>
>> can@0 {
>> @@ -103,9 +86,6 @@ can@0 {
>> };
>>
>> &ecspi3 {
>> - pinctrl-names = "default";
>> - pinctrl-0 = <&pinctrl_ecspi3>;
>> - cs-gpios = <&gpio5 25 GPIO_ACTIVE_LOW>;
>> status = "okay";
>>
>> eeram@0 {
>> @@ -117,7 +97,7 @@ eeram@0 {
>>
>> &fec1 {
>> pinctrl-names = "default";
>> - pinctrl-0 = <&pinctrl_enet>;
>> + pinctrl-0 = <&pinctrl_enet_rgmii>;
>> phy-connection-type = "rgmii-id";
>> phy-handle = <ðphy>;
>> status = "okay";
>> @@ -136,27 +116,59 @@ ethphy: ethernet-phy@0 {
>> };
>> };
>>
>> +/*
>> + * Rename SoM signals according to board usage:
>> + * GPIO_B_0 -> DIO1_OUT
>> + * GPIO_B_1 -> DIO2_OUT
>> + */
>> &gpio1 {
>> - pinctrl-names = "default";
>> - pinctrl-0 = <&pinctrl_gpio1>;
>> - gpio-line-names = "", "", "", "dio1-out", "", "", "dio1-in", "dio2-out",
>> - "dio2-in", "dio3-out", "dio3-in", "dio4-out", "", "", "", "",
>> - "", "", "", "", "", "", "", "",
>> - "", "", "", "", "", "", "", "";
>> + gpio-line-names = "", "GPIO_A_0", "", "GPIO_A_1",
>> + "", "GPIO_A_2", "GPIO_A_3", "GPIO_A_4",
>> + "GPIO_A_5", "GPIO_A_6", "GPIO_A_7", "DIO1_OUT",
>> + "DIO2_OUT", "USB_A_OC#", "CAM_MCK", "USB_B_OC#",
>> + "ETH_MDC", "ETH_MDIO", "ETH_A_(S)(R)(G)MII_TXD3",
>> + "ETH_A_(S)(R)(G)MII_TXD2", "ETH_A_(S)(R)(G)MII_TXD1",
>> + "ETH_A_(S)(R)(G)MII_TXD0", "ETH_A_(R)(G)MII_TX_EN(_ER)",
>> + "ETH_A_(R)(G)MII_TX_CLK", "ETH_A_(R)(G)MII_RX_DV(_ER)",
>> + "ETH_A_(R)(G)MII_RX_CLK", "ETH_A_(S)(R)(G)MII_RXD0",
>> + "ETH_A_(S)(R)(G)MII_RXD1", "ETH_A_(R)(G)MII_RXD2",
>> + "ETH_A_(R)(G)MII_RXD3";
>> };
>>
>> -&gpio5 {
>> - pinctrl-names = "default";
>> - pinctrl-0 = <&pinctrl_gpio5>;
>> - gpio-line-names = "", "", "dio4-in", "", "", "", "", "",
>> - "", "", "", "", "", "", "", "",
>> - "", "", "", "", "", "", "", "",
>> - "", "", "", "", "", "", "", "";
>> +/*
>> + * Rename SoM signals according to board usage:
>> + * GPIO_B_2 -> DIO3_OUT
>> + * GPIO_B_3 -> DIO4_OUT
>> + */
>> +&gpio3 {
>> + gpio-line-names = "GPIO_C_5", "GPIO_C_4", "SDIO_B_CD#", "SDIO_B_D5",
>> + "SDIO_B_D6", "SDIO_B_D7", "GPIO_C_0", "GPIO_C_1",
>> + "GPIO_C_2", "GPIO_C_3", "SDIO_B_D0", "SDIO_B_D1",
>> + "SDIO_B_D2", "SDIO_B_D3", "", "SDIO_B_D4",
>> + "CARRIER_PWR_EN", "SDIO_B_CLK", "SDIO_B_CMD", "DIO3_OUT",
>> + "USB_B_EN", "DIO4_OUT", "PCIe_CLKREQ#", "PCIe_A_PERST#",
>> + "PCIe_WAKE#", "USB_A_EN";
>> +};
>> +
>> +/*
>> + * Rename SoM signals according to board usage:
>> + * GPIO_B_4 -> DIO1_IN
>> + * GPIO_B_5 -> DIO2_IN
>> + * GPIO_B_6 -> DIO3_IN
>> + * GPIO_B_7 -> DIO4_IN
>> + */
>> +&gpio4 {
>> + gpio-line-names = "GPIO_C_7", "", "I2S_A_DATA_IN", "I2S_B_DATA_IN",
>> + "DIO1_IN", "BOOT_SEL0#", "BOOT_SEL1#", "",
>> + "", "", "I2S_LRCLK", "I2S_BITCLK",
>> + "I2S_A_DATA_OUT", "I2S_B_DATA_OUT", "DIO2_IN", "DIO3_IN",
>> + "DIO4_IN", "SPI_A_/WP_(IO2)", "SPI_A_/HOLD_(IO3)", "GPIO_C_6",
>> + "I2S_MCLK", "UART_A_TX", "UART_A_RX", "UART_A_CTS",
>> + "UART_A_RTS", "", "", "",
>> + "PCIe_SM_ALERT", "UART_B_RTS", "UART_B_CTS", "UART_B_RX";
>> };
>>
>> &i2c3 {
>> - pinctrl-names = "default";
>> - pinctrl-0 = <&pinctrl_i2c3>;
>> status = "okay";
>>
>> usb-hub@2c {
>> @@ -169,27 +181,28 @@ usb-hub@2c {
>> };
>> };
>>
>> -&i2c4 {
>> - pinctrl-names = "default";
>> - pinctrl-0 = <&pinctrl_i2c4>;
>> -};
>> -
>> &pwm2 {
>> - pinctrl-names = "default";
>> - pinctrl-0 = <&pinctrl_pwm2>;
>> status = "okay";
>> };
>>
>> +®_usb2_vbus {
>> + status = "disabled";
>> +};
>> +
>> +®_usdhc2_vcc {
>> + status = "disabled";
>> +};
>> +
>> +®_usdhc3_vcc {
>> + status = "disabled";
>> +};
>> +
>> &uart1 {
>> - pinctrl-names = "default";
>> - pinctrl-0 = <&pinctrl_uart1>;
>> uart-has-rtscts;
>> status = "okay";
>> };
>>
>> &uart2 {
>> - pinctrl-names = "default";
>> - pinctrl-0 = <&pinctrl_uart2>;
>> linux,rs485-enabled-at-boot-time;
>> uart-has-rtscts;
>> status = "okay";
>> @@ -197,8 +210,6 @@ &uart2 {
>>
>> &usbotg1 {
>> dr_mode = "otg";
>> - disable-over-current;
>> - vbus-supply = <®_usb1_vbus>;
>> status = "okay";
>> };
>>
>> @@ -209,6 +220,9 @@ &usbotg2 {
>> #size-cells = <0>;
>> status = "okay";
>>
>> + /* VBUS is controlled by the hub */
>> + /delete-property/ vbus-supply;
>> +
>> usb1@1 {
>> compatible = "usb424,2514";
>> reg = <1>;
>> @@ -224,171 +238,20 @@ usbnet: ethernet@1 {
>> };
>>
>> &usdhc2 {
>> - pinctrl-names = "default", "state_100mhz", "state_200mhz";
>> - pinctrl-0 = <&pinctrl_usdhc2>;
>> - pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
>> - pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
>> vmmc-supply = <®_vdd_3v3>;
>> - vqmmc-supply = <®_nvcc_sd>;
>> - cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
>> status = "okay";
>> };
>>
>> &iomuxc {
>> pinctrl_can: cangrp {
>> fsl,pins = <
>> - MX8MM_IOMUXC_SAI3_TXD_GPIO5_IO1 0x19
>> - >;
>> - };
>> -
>> - pinctrl_ecspi2: ecspi2grp {
>> - fsl,pins = <
>> - MX8MM_IOMUXC_ECSPI2_MISO_ECSPI2_MISO 0x82
>> - MX8MM_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI 0x82
>> - MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK 0x82
>> - MX8MM_IOMUXC_ECSPI2_SS0_GPIO5_IO13 0x19
>> - >;
>> - };
>> -
>> - pinctrl_ecspi3: ecspi3grp {
>> - fsl,pins = <
>> - MX8MM_IOMUXC_UART2_RXD_ECSPI3_MISO 0x82
>> - MX8MM_IOMUXC_UART1_TXD_ECSPI3_MOSI 0x82
>> - MX8MM_IOMUXC_UART1_RXD_ECSPI3_SCLK 0x82
>> - MX8MM_IOMUXC_UART2_TXD_GPIO5_IO25 0x19
>> - >;
>> - };
>> -
>> - pinctrl_enet: enetgrp {
>> - fsl,pins = <
>> - MX8MM_IOMUXC_ENET_MDC_ENET1_MDC 0x3
>> - MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO 0x3
>> - MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x1f
>> - MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x1f
>> - MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x1f
>> - MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x1f
>> - MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x91
>> - MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x91
>> - MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x91
>> - MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x91
>> - MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x1f
>> - MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x91
>> - MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x91
>> - MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x1f
>> - MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3 0x19 /* PHY RST */
>> - >;
>> - };
>> -
>> - pinctrl_gpio_led: gpioledgrp {
>> - fsl,pins = <
>> - MX8MM_IOMUXC_GPIO1_IO05_GPIO1_IO5 0x19
>> - MX8MM_IOMUXC_GPIO1_IO07_GPIO1_IO7 0x19
>> - MX8MM_IOMUXC_GPIO1_IO08_GPIO1_IO8 0x19
>> - >;
>> - };
>> -
>> - pinctrl_gpio1: gpio1grp {
>> - fsl,pins = <
>> - MX8MM_IOMUXC_GPIO1_IO01_GPIO1_IO1 0x19
>> - MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x19
>> - MX8MM_IOMUXC_GPIO1_IO11_GPIO1_IO11 0x19
>> - MX8MM_IOMUXC_GPIO1_IO06_GPIO1_IO6 0x19
>> - MX8MM_IOMUXC_GPIO1_IO10_GPIO1_IO10 0x19
>> - >;
>> - };
>> -
>> - pinctrl_gpio5: gpio5grp {
>> - fsl,pins = <
>> - MX8MM_IOMUXC_SAI3_MCLK_GPIO5_IO2 0x19
>> - >;
>> - };
>> -
>> - pinctrl_i2c3: i2c3grp {
>> - fsl,pins = <
>> - MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL 0x40000083
>> - MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA 0x40000083
>> - >;
>> - };
>> -
>> - pinctrl_i2c4: i2c4grp {
>> - fsl,pins = <
>> - MX8MM_IOMUXC_I2C4_SCL_I2C4_SCL 0x40000083
>> - MX8MM_IOMUXC_I2C4_SDA_I2C4_SDA 0x40000083
>> - >;
>> - };
>> -
>> - pinctrl_pwm2: pwm2grp {
>> - fsl,pins = <
>> - MX8MM_IOMUXC_SPDIF_RX_PWM2_OUT 0x19
>> - >;
>> - };
>> -
>> - pinctrl_reg_usb1_vbus: regusb1vbusgrp {
>> - fsl,pins = <
>> - MX8MM_IOMUXC_SAI5_MCLK_GPIO3_IO25 0x19
>> - >;
>> - };
>> -
>> - pinctrl_uart1: uart1grp {
>> - fsl,pins = <
>> - MX8MM_IOMUXC_SAI2_RXC_UART1_DCE_RX 0x0
>> - MX8MM_IOMUXC_SAI2_RXFS_UART1_DCE_TX 0x0
>> - MX8MM_IOMUXC_SAI2_RXD0_UART1_DCE_RTS_B 0x0
>> - MX8MM_IOMUXC_SAI2_TXFS_UART1_DCE_CTS_B 0x0
>> - >;
>> - };
>> -
>> - pinctrl_uart2: uart2grp {
>> - fsl,pins = <
>> - MX8MM_IOMUXC_SAI3_TXFS_UART2_DCE_RX 0x0
>> - MX8MM_IOMUXC_SAI3_TXC_UART2_DCE_TX 0x0
>> - MX8MM_IOMUXC_SAI3_RXD_UART2_DCE_RTS_B 0x0
>> - MX8MM_IOMUXC_SAI3_RXC_UART2_DCE_CTS_B 0x0
>> - >;
>> - };
>> -
>> - pinctrl_usb_eth2: usbeth2grp {
>> - fsl,pins = <
>> - MX8MM_IOMUXC_GPIO1_IO01_GPIO1_IO1 0x19
>> - >;
>> - };
>> -
>> - pinctrl_usdhc2: usdhc2grp {
>> - fsl,pins = <
>> - MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x90
>> - MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d0
>> - MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d0
>> - MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d0
>> - MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d0
>> - MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d0
>> - MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12 0x19
>> - MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x90
>> - >;
>> - };
>> -
>> - pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
>> - fsl,pins = <
>> - MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x94
>> - MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4
>> - MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4
>> - MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4
>> - MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4
>> - MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4
>> - MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12 0x19
>> - MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x90
>> + MX8MM_IOMUXC_SAI3_TXD_GPIO5_IO1 0x19 /* SDIO_B_PWR_EN */
>> >;
>> };
>>
>> - pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
>> + pinctrl_usb_hub: usbhubgrp {
>> fsl,pins = <
>> - MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x96
>> - MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d6
>> - MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d6
>> - MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d6
>> - MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d6
>> - MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d6
>> - MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12 0x19
>> - MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x90
>> + MX8MM_IOMUXC_SAI3_MCLK_GPIO5_IO2 0x19 /* SDIO_B_WP */
>> >;
>> };
>> };
>> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi
>> index 6b9058fc53332..1a5c29565e7fe 100644
>> --- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi
>> +++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi
>> @@ -3,6 +3,7 @@
>> * Copyright (C) 2022 Kontron Electronics GmbH
>> */
>>
>> +#include <dt-bindings/gpio/gpio.h>
>> #include <dt-bindings/interrupt-controller/irq.h>
>> #include "imx8mm.dtsi"
>>
>> @@ -28,6 +29,73 @@ memory@40000000 {
>> chosen {
>> stdout-path = &uart3;
>> };
>> +
>> + reg_vdd_carrier: regulator-vdd-carrier {
>> + compatible = "regulator-fixed";
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pinctrl_reg_vdd_carrier>;
>> + enable-active-high;
>> + gpio = <&gpio3 16 GPIO_ACTIVE_HIGH>;
>
> Can we flip the order of these two properties? enable-active-high is a
> further description to GPIO_ACTIVE_HIGH.
Sure, done in v3
>> + regulator-always-on;
>> + regulator-boot-on;
>> + regulator-name = "VDD_CARRIER";
>> +
>> + regulator-state-standby {
>> + regulator-on-in-suspend;
>> + };
>> +
>> + regulator-state-mem {
>> + regulator-off-in-suspend;
>> + };
>> +
>> + regulator-state-disk {
>> + regulator-off-in-suspend;
>> + };
>> + };
>> +
>> + reg_usb1_vbus: regulator-usb1-vbus {
>> + compatible = "regulator-fixed";
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pinctrl_reg_usb1_vbus>;
>> + enable-active-high;
>> + gpio = <&gpio3 25 GPIO_ACTIVE_HIGH>;
>> + regulator-min-microvolt = <5000000>;
>> + regulator-max-microvolt = <5000000>;
>> + regulator-name = "VBUS_USB1";
>> + };
>> +
>> + reg_usb2_vbus: regulator-usb2-vbus {
>> + compatible = "regulator-fixed";
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pinctrl_reg_usb2_vbus>;
>> + enable-active-high;
>> + gpio = <&gpio3 20 GPIO_ACTIVE_HIGH>;
>> + regulator-min-microvolt = <5000000>;
>> + regulator-max-microvolt = <5000000>;
>> + regulator-name = "VBUS_USB2";
>> + };
>> +
>> + reg_usdhc2_vcc: regulator-usdhc2-vcc {
>> + compatible = "regulator-fixed";
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pinctrl_reg_usdhc2_vcc>;
>> + enable-active-high;
>> + gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
>> + regulator-min-microvolt = <3300000>;
>> + regulator-max-microvolt = <3300000>;
>> + regulator-name = "VCC_SDIO_A";
>> + };
>> +
>> + reg_usdhc3_vcc: regulator-usdhc3-vcc {
>> + compatible = "regulator-fixed";
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pinctrl_reg_usdhc3_vcc>;
>> + enable-active-high;
>> + gpio = <&gpio5 1 GPIO_ACTIVE_HIGH>;
>> + regulator-min-microvolt = <3300000>;
>> + regulator-max-microvolt = <3300000>;
>> + regulator-name = "VCC_SDIO_B";
>> + };
>> };
>>
>> &A53_0 {
>> @@ -96,6 +164,79 @@ partition@1f0000 {
>> };
>> };
>>
>> +&ecspi2 {
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pinctrl_ecspi2>, <&pinctrl_ecspi2_gpio>;
>> + cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
>> +};
>> +
>> +&ecspi3 {
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pinctrl_ecspi3>;
>> + cs-gpios = <&gpio5 25 GPIO_ACTIVE_LOW>;
>> +};
>> +
>> +&gpio1 {
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pinctrl_gpio1>;
>> + gpio-line-names = "", "GPIO_A_0", "", "GPIO_A_1",
>> + "", "GPIO_A_2", "GPIO_A_3", "GPIO_A_4",
>> + "GPIO_A_5", "GPIO_A_6", "GPIO_A_7", "GPIO_B_0",
>> + "GPIO_B_1", "USB_A_OC#", "CAM_MCK", "USB_B_OC#",
>> + "ETH_MDC", "ETH_MDIO", "ETH_A_(S)(R)(G)MII_TXD3",
>> + "ETH_A_(S)(R)(G)MII_TXD2", "ETH_A_(S)(R)(G)MII_TXD1",
>> + "ETH_A_(S)(R)(G)MII_TXD0", "ETH_A_(R)(G)MII_TX_EN(_ER)",
>> + "ETH_A_(R)(G)MII_TX_CLK", "ETH_A_(R)(G)MII_RX_DV(_ER)",
>> + "ETH_A_(R)(G)MII_RX_CLK", "ETH_A_(S)(R)(G)MII_RXD0",
>> + "ETH_A_(S)(R)(G)MII_RXD1", "ETH_A_(R)(G)MII_RXD2",
>> + "ETH_A_(R)(G)MII_RXD3";
>> +};
>> +
>> +&gpio2 {
>> + gpio-line-names = "", "", "", "",
>> + "", "", "", "",
>> + "", "", "", "",
>> + "SDIO_A_CD#", "SDIO_A_CLK", "SDIO_A_CMD", "SDIO_A_D0",
>> + "SDIO_A_D1", "SDIO_A_D2", "SDIO_A_D3", "SDIO_A_PWR_EN",
>> + "SDIO_A_WP";
>> +};
>> +
>> +&gpio3 {
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pinctrl_gpio3>;
>> + gpio-line-names = "GPIO_C_5", "GPIO_C_4", "SDIO_B_CD#", "SDIO_B_D5",
>> + "SDIO_B_D6", "SDIO_B_D7", "GPIO_C_0", "GPIO_C_1",
>> + "GPIO_C_2", "GPIO_C_3", "SDIO_B_D0", "SDIO_B_D1",
>> + "SDIO_B_D2", "SDIO_B_D3", "", "SDIO_B_D4",
>> + "CARRIER_PWR_EN", "SDIO_B_CLK", "SDIO_B_CMD", "GPIO_B_2",
>> + "USB_B_EN", "GPIO_B_3", "PCIe_CLKREQ#", "PCIe_A_PERST#",
>> + "PCIe_WAKE#", "USB_A_EN";
>> +};
>> +
>> +&gpio4 {
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pinctrl_gpio4>;
>> + gpio-line-names = "GPIO_C_7", "", "I2S_A_DATA_IN", "I2S_B_DATA_IN",
>> + "GPIO_B_4", "BOOT_SEL0#", "BOOT_SEL1#", "",
>> + "", "", "I2S_LRCLK", "I2S_BITCLK",
>> + "I2S_A_DATA_OUT", "I2S_B_DATA_OUT", "GPIO_B_5", "GPIO_B_6",
>> + "GPIO_B_7", "SPI_A_/WP_(IO2)", "SPI_A_/HOLD_(IO3)", "GPIO_C_6",
>> + "I2S_MCLK", "UART_A_TX", "UART_A_RX", "UART_A_CTS",
>> + "UART_A_RTS", "", "", "",
>> + "PCIe_SM_ALERT", "UART_B_RTS", "UART_B_CTS", "UART_B_RX";
>> +};
>> +
>> +&gpio5 {
>> + gpio-line-names = "UART_B_TX", "SDIO_B_PWR_EN", "SDIO_B_WP", "PWM_2",
>> + "PWM_1", "PWM_0", "", "",
>> + "", "", "SPI_A_SCK", "SPI_A_SDO_(IO1)",
>> + "SPI_A_SCK", "SPI_A_CS0#", "", "",
>> + "I2C_A_SCL", "I2C_A_SDA", "I2C_B_SCL", "I2C_B_SDA",
>> + "PCIe_SMCLK", "PCIe_SMDAT", "SPI_B_SCK", "SPI_B_SDO",
>> + "SPI_B_SDI", "SPI_B_CS0#", "UART_CON_RX", "UART_CON_TX",
>> + "UART_C_RX", "UART_C_TX";
>> +};
>> +
>> &i2c1 {
>> clock-frequency = <400000>;
>> pinctrl-names = "default";
>> @@ -222,12 +363,69 @@ rv3028: rtc@52 {
>> };
>> };
>>
>> +&i2c2 {
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pinctrl_i2c2>;
>> +};
>> +
>> +&i2c3 {
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pinctrl_i2c3>;
>> +};
>> +
>> +&i2c4 {
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pinctrl_i2c4>;
>> +};
>> +
>> +&pwm1 {
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pinctrl_pwm1>;
>> +};
>> +
>> +&pwm2 {
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pinctrl_pwm2>;
>> +};
>> +
>> +&pwm3 {
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pinctrl_pwm3>;
>> +};
>> +
>> +&uart1 {
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pinctrl_uart1>;
>> +};
>> +
>> +&uart2 {
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pinctrl_uart2>;
>> +};
>> +
>> &uart3 { /* console */
>> pinctrl-names = "default";
>> pinctrl-0 = <&pinctrl_uart3>;
>> status = "okay";
>> };
>>
>> +&uart4 {
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pinctrl_uart4>;
>> +};
>> +
>> +&usbotg1 {
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pinctrl_usb1>;
>> + vbus-supply = <®_usb1_vbus>;
>> +};
>> +
>> +&usbotg2 {
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pinctrl_usb2>;
>> + vbus-supply = <®_usb2_vbus>;
>> +};
>> +
>> &usdhc1 {
>> pinctrl-names = "default", "state_100mhz", "state_200mhz";
>> pinctrl-0 = <&pinctrl_usdhc1>;
>> @@ -240,6 +438,26 @@ &usdhc1 {
>> status = "okay";
>> };
>>
>> +&usdhc2 {
>> + pinctrl-names = "default", "state_100mhz", "state_200mhz";
>> + pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
>> + pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
>> + pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
>> + vmmc-supply = <®_usdhc2_vcc>;
>> + vqmmc-supply = <®_nvcc_sd>;
>> + cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
>> +};
>> +
>> +&usdhc3 {
>> + pinctrl-names = "default", "state_100mhz", "state_200mhz";
>> + pinctrl-0 = <&pinctrl_usdhc3>, <&pinctrl_usdhc3_gpio>;
>> + pinctrl-1 = <&pinctrl_usdhc3_100mhz>, <&pinctrl_usdhc3_gpio>;
>> + pinctrl-2 = <&pinctrl_usdhc3_200mhz>, <&pinctrl_usdhc3_gpio>;
>> + vmmc-supply = <®_usdhc3_vcc>;
>> + vqmmc-supply = <®_nvcc_sd>;
>> + cd-gpios = <&gpio3 2 GPIO_ACTIVE_LOW>;
>> +};
>> +
>> &wdog1 {
>> pinctrl-names = "default";
>> pinctrl-0 = <&pinctrl_wdog>;
>> @@ -248,6 +466,12 @@ &wdog1 {
>> };
>>
>> &iomuxc {
>> + pinctrl_csi_mck: csimckgrp {
>> + fsl,pins = <
>> + MX8MM_IOMUXC_GPIO1_IO14_CCMSRCGPCMIX_CLKO1 0x59 /* CAM_MCK */
>> + >;
>> + };
>> +
>> pinctrl_ecspi1: ecspi1grp {
>> fsl,pins = <
>> MX8MM_IOMUXC_ECSPI1_MISO_ECSPI1_MISO 0x82
>> @@ -257,6 +481,106 @@ MX8MM_IOMUXC_ECSPI1_SS0_GPIO5_IO9 0x19
>> >;
>> };
>>
>> + pinctrl_ecspi2: ecspi2grp {
>> + fsl,pins = <
>> + MX8MM_IOMUXC_ECSPI2_MISO_ECSPI2_MISO 0x82 /* SPI_A_SDI_(IO0) */
>> + MX8MM_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI 0x82 /* SPI_A_SDO_(IO1) */
>> + MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK 0x82 /* SPI_A_SCK */
>> + MX8MM_IOMUXC_ECSPI2_SS0_GPIO5_IO13 0x19 /* SPI_A_CS0# */
>> + >;
>> + };
>> +
>> + pinctrl_ecspi2_gpio: ecspi2gpiogrp {
>> + fsl,pins = <
>> + MX8MM_IOMUXC_SAI1_TXD5_GPIO4_IO17 0x19 /* SPI_A_/WP_(IO2) */
>> + MX8MM_IOMUXC_SAI1_TXD6_GPIO4_IO18 0x19 /* SPI_A_/HOLD_(IO3) */
>> + >;
>> + };
>> +
>> + pinctrl_ecspi3: ecspi3grp {
>> + fsl,pins = <
>> + MX8MM_IOMUXC_UART2_RXD_ECSPI3_MISO 0x82 /* SPI_B_SDI */
>> + MX8MM_IOMUXC_UART1_TXD_ECSPI3_MOSI 0x82 /* SPI_B_SDO */
>> + MX8MM_IOMUXC_UART1_RXD_ECSPI3_SCLK 0x82 /* SPI_B_SCK */
>> + MX8MM_IOMUXC_UART2_TXD_GPIO5_IO25 0x19 /* SPI_B_CS0# */
>> + >;
>> + };
>> +
>> + pinctrl_enet_rgmii: enetrgmiigrp {
>> + fsl,pins = <
>> + MX8MM_IOMUXC_ENET_MDC_ENET1_MDC 0x03 /* ETH_MDC */
>> + MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO 0x03 /* ETH_MDIO */
>> + MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x1f /* ETH_A_(S)(R)(G)MII_TXD3 */
>> + MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x1f /* ETH_A_(S)(R)(G)MII_TXD2 */
>> + MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x1f /* ETH_A_(S)(R)(G)MII_TXD1 */
>> + MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x1f /* ETH_A_(S)(R)(G)MII_TXD0 */
>> + MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x91 /* ETH_A_(R)(G)MII_RXD3 */
>> + MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x91 /* ETH_A_(R)(G)MII_RXD2 */
>> + MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x91 /* ETH_A_(S)(R)(G)MII_RXD1 */
>> + MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x91 /* ETH_A_(S)(R)(G)MII_RXD0 */
>> + MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x1f /* ETH_A_(R)(G)MII_TX_CLK */
>> + MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x91 /* ETH_A_(R)(G)MII_RX_CLK */
>> + MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x91 /* ETH_A_(R)(G)MII_RX_DV(_ER) */
>> + MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x1f /* ETH_A_(R)(G)MII_TX_EN(_ER) */
>> + >;
>> + };
>> +
>> + pinctrl_enet_rmii: enetrmiigrp {
>> + fsl,pins = <
>> + MX8MM_IOMUXC_ENET_MDC_ENET1_MDC 0x03 /* ETH_MDC */
>> + MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO 0x03 /* ETH_MDIO */
>> + MX8MM_IOMUXC_ENET_TD2_ENET1_TX_CLK 0x4000001f /* ETH_A_(S)(R)(G)MII_TXD2 */
>> + MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x56 /* ETH_A_(S)(R)(G)MII_TXD1 */
>> + MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x56 /* ETH_A_(S)(R)(G)MII_TXD0 */
>> + MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x56 /* ETH_A_(S)(R)(G)MII_RXD1 */
>> + MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x56 /* ETH_A_(S)(R)(G)MII_RXD0 */
>> + MX8MM_IOMUXC_ENET_RXC_ENET1_RX_ER 0x56 /* ETH_A_(R)(G)MII_RX_CLK */
>> + MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x56 /* ETH_A_(R)(G)MII_RX_DV(_ER) */
>> + MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x56 /* ETH_A_(R)(G)MII_TX_EN(_ER) */
>> + >;
>> + };
>> +
>> + pinctrl_gpio1: gpio1grp {
>> + fsl,pins = <
>> + MX8MM_IOMUXC_GPIO1_IO01_GPIO1_IO1 0x19 /* GPIO_A_0 */
>> + MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3 0x19 /* GPIO_A_1 */
>> + MX8MM_IOMUXC_GPIO1_IO05_GPIO1_IO5 0x19 /* GPIO_A_2 */
>> + MX8MM_IOMUXC_GPIO1_IO06_GPIO1_IO6 0x19 /* GPIO_A_3 */
>> + MX8MM_IOMUXC_GPIO1_IO07_GPIO1_IO7 0x19 /* GPIO_A_4 */
>> + MX8MM_IOMUXC_GPIO1_IO08_GPIO1_IO8 0x19 /* GPIO_A_5 */
>> + MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x19 /* GPIO_A_6 */
>> + MX8MM_IOMUXC_GPIO1_IO10_GPIO1_IO10 0x19 /* GPIO_A_7 */
>> + MX8MM_IOMUXC_GPIO1_IO11_GPIO1_IO11 0x19 /* GPIO_B_0 */
>> + MX8MM_IOMUXC_GPIO1_IO12_GPIO1_IO12 0x19 /* GPIO_B_1 */
>> + >;
>> + };
>> +
>> + pinctrl_gpio3: gpio3grp {
>> + fsl,pins = <
>> + MX8MM_IOMUXC_NAND_ALE_GPIO3_IO0 0x19 /* GPIO_C_5 */
>> + MX8MM_IOMUXC_NAND_CE0_B_GPIO3_IO1 0x19 /* GPIO_C_4 */
>> + MX8MM_IOMUXC_NAND_DATA00_GPIO3_IO6 0x19 /* GPIO_C_0 */
>> + MX8MM_IOMUXC_NAND_DATA01_GPIO3_IO7 0x19 /* GPIO_C_1 */
>> + MX8MM_IOMUXC_NAND_DATA02_GPIO3_IO8 0x19 /* GPIO_C_2 */
>> + MX8MM_IOMUXC_NAND_DATA03_GPIO3_IO9 0x19 /* GPIO_C_3 */
>> + MX8MM_IOMUXC_SAI5_RXFS_GPIO3_IO19 0x19 /* GPIO_B_2 */
>> + MX8MM_IOMUXC_SAI5_RXD0_GPIO3_IO21 0x19 /* GPIO_B_3 */
>> + >;
>> + };
>> +
>> + pinctrl_gpio4: gpio4grp {
>> + fsl,pins = <
>> + MX8MM_IOMUXC_SAI1_RXFS_GPIO4_IO0 0x19 /* GPIO_C_7 */
>> + MX8MM_IOMUXC_SAI1_RXD2_GPIO4_IO4 0x19 /* GPIO_B_4 */
>> + MX8MM_IOMUXC_SAI1_RXD3_GPIO4_IO5 0x19 /* BOOT_SEL0# */
>> + MX8MM_IOMUXC_SAI1_RXD4_GPIO4_IO6 0x19 /* BOOT_SEL1# */
>> + MX8MM_IOMUXC_SAI1_TXD2_GPIO4_IO14 0x19 /* GPIO_B_5 */
>> + MX8MM_IOMUXC_SAI1_TXD3_GPIO4_IO15 0x19 /* GPIO_B_6 */
>> + MX8MM_IOMUXC_SAI1_TXD4_GPIO4_IO16 0x19 /* GPIO_B_7 */
>> + MX8MM_IOMUXC_SAI1_TXD7_GPIO4_IO19 0x19 /* GPIO_C_6 */
>> + >;
>> + };
>> +
>> pinctrl_i2c1: i2c1grp {
>> fsl,pins = <
>> MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL 0x40000083
>> @@ -264,22 +588,149 @@ MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA 0x40000083
>> >;
>> };
>>
>> + pinctrl_i2c2: i2c2grp {
>> + fsl,pins = <
>> + MX8MM_IOMUXC_I2C2_SCL_I2C2_SCL 0x40000083 /* I2C_A_SCL */
>> + MX8MM_IOMUXC_I2C2_SDA_I2C2_SDA 0x40000083 /* I2C_A_SDA */
>> + >;
>> + };
>> +
>> + pinctrl_i2c3: i2c3grp {
>> + fsl,pins = <
>> + MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL 0x40000083 /* I2C_B_SCL */
>> + MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA 0x40000083 /* I2C_B_SDA */
>> + >;
>> + };
>> +
>> + pinctrl_i2c4: i2c4grp {
>> + fsl,pins = <
>> + MX8MM_IOMUXC_I2C4_SCL_I2C4_SCL 0x40000083 /* PCIe_SMCLK and I2C_CAM_SCL/CSI_TX_P */
>> + MX8MM_IOMUXC_I2C4_SDA_I2C4_SDA 0x40000083 /* PCIe_SMDAT and I2C_CAM_SDA/CSI_TX_N */
>> + >;
>> + };
>> +
>> + pinctrl_pcie: pciegrp {
>> + fsl,pins = <
>> + MX8MM_IOMUXC_SAI5_RXD1_GPIO3_IO22 0x19 /* PCIe_CLKREQ# */
>> + MX8MM_IOMUXC_SAI5_RXD2_GPIO3_IO23 0x19 /* PCIe_A_PERST# */
>> + MX8MM_IOMUXC_SAI5_RXD3_GPIO3_IO24 0x19 /* PCIe_WAKE# */
>> + MX8MM_IOMUXC_SAI3_RXFS_GPIO4_IO28 0x19 /* PCIe_SM_ALERT */
>> + >;
>> + };
>> +
>> pinctrl_pmic: pmicgrp {
>> fsl,pins = <
>> MX8MM_IOMUXC_GPIO1_IO00_GPIO1_IO0 0x141
>> >;
>> };
>>
>> + pinctrl_pwm1: pwm1grp {
>> + fsl,pins = <
>> + MX8MM_IOMUXC_SPDIF_EXT_CLK_PWM1_OUT 0x19 /* PWM_0 */
>> + >;
>> + };
>> +
>> + pinctrl_pwm2: pwm2grp {
>> + fsl,pins = <
>> + MX8MM_IOMUXC_SPDIF_RX_PWM2_OUT 0x19 /* PWM_1 */
>> + >;
>> + };
>> +
>> + pinctrl_pwm3: pwm3grp {
>> + fsl,pins = <
>> + MX8MM_IOMUXC_SPDIF_TX_PWM3_OUT 0x19 /* PWM_2 */
>> + >;
>> + };
>> +
>> + pinctrl_reg_usb1_vbus: regusb1vbusgrp {
>> + fsl,pins = <
>> + MX8MM_IOMUXC_SAI5_MCLK_GPIO3_IO25 0x19 /* USB_A_EN */
>> + >;
>> + };
>> +
>> + pinctrl_reg_usb2_vbus: regusb2vbusgrp {
>> + fsl,pins = <
>> + MX8MM_IOMUXC_SAI5_RXC_GPIO3_IO20 0x19 /* USB_B_EN */
>> + >;
>> + };
>> +
>> + pinctrl_reg_usdhc2_vcc: regusdhc2vccgrp {
>> + fsl,pins = <
>> + MX8MM_IOMUXC_SD2_RESET_B_GPIO2_IO19 0x19 /* SDIO_A_PWR_EN */
>> + >;
>> + };
>> +
>> + pinctrl_reg_usdhc3_vcc: regusdhc3vccgrp {
>> + fsl,pins = <
>> + MX8MM_IOMUXC_SAI3_TXD_GPIO5_IO1 0x19 /* SDIO_B_PWR_EN */
>> + >;
>> + };
>> +
>> + pinctrl_reg_vdd_carrier: regvddcarriergrp {
>> + fsl,pins = <
>> + MX8MM_IOMUXC_NAND_READY_B_GPIO3_IO16 0x19 /* CARRIER_PWR_EN */
>> + >;
>> + };
>> +
>> pinctrl_rtc: rtcgrp {
>> fsl,pins = <
>> MX8MM_IOMUXC_SAI1_RXC_GPIO4_IO1 0x19
>> >;
>> };
>>
>> + pinctrl_sai1: sai1grp {
>> + fsl,pins = <
>> + MX8MM_IOMUXC_SAI1_RXD0_SAI1_RX_DATA0 0xd6 /* I2S_A_DATA_IN */
>> + MX8MM_IOMUXC_SAI1_TXD0_SAI1_TX_DATA0 0xd6 /* I2S_A_DATA_OUT */
>> + MX8MM_IOMUXC_SAI1_RXD1_SAI1_RX_DATA1 0xd6 /* I2S_B_DATA_IN */
>> + MX8MM_IOMUXC_SAI1_TXD1_SAI1_TX_DATA1 0xd6 /* I2S_B_DATA_OUT */
>> + MX8MM_IOMUXC_SAI1_MCLK_SAI1_MCLK 0xd6 /* I2S_MCLK */
>> + MX8MM_IOMUXC_SAI1_TXFS_SAI1_TX_SYNC 0xd6 /* I2S_LRCLK */
>> + MX8MM_IOMUXC_SAI1_TXC_SAI1_TX_BCLK 0xd6 /* I2S_BITCLK */
>> + >;
>> + };
>> +
>> + pinctrl_uart1: uart1grp {
>> + fsl,pins = <
>> + MX8MM_IOMUXC_SAI2_RXC_UART1_DCE_RX 0x0 /* UART_A_RX */
>> + MX8MM_IOMUXC_SAI2_RXFS_UART1_DCE_TX 0x0 /* UART_A_TX */
>> + MX8MM_IOMUXC_SAI2_RXD0_UART1_DCE_RTS_B 0x0 /* UART_A_CTS */
>> + MX8MM_IOMUXC_SAI2_TXFS_UART1_DCE_CTS_B 0x0 /* UART_A_RTS */
>> + >;
>> + };
>> +
>> + pinctrl_uart2: uart2grp {
>> + fsl,pins = <
>> + MX8MM_IOMUXC_SAI3_TXFS_UART2_DCE_RX 0x0 /* UART_B_RX */
>> + MX8MM_IOMUXC_SAI3_TXC_UART2_DCE_TX 0x0 /* UART_B_TX */
>> + MX8MM_IOMUXC_SAI3_RXD_UART2_DCE_RTS_B 0x0 /* UART_B_CTS */
>> + MX8MM_IOMUXC_SAI3_RXC_UART2_DCE_CTS_B 0x0 /* UART_B_RTS */
>> + >;
>> + };
>> +
>> pinctrl_uart3: uart3grp {
>> fsl,pins = <
>> - MX8MM_IOMUXC_UART3_RXD_UART3_DCE_RX 0x140
>> - MX8MM_IOMUXC_UART3_TXD_UART3_DCE_TX 0x140
>> + MX8MM_IOMUXC_UART3_RXD_UART3_DCE_RX 0x140 /* UART_CON_RX */
>> + MX8MM_IOMUXC_UART3_TXD_UART3_DCE_TX 0x140 /* UART_CON_TX */
>> + >;
>> + };
>> +
>> + pinctrl_uart4: uart4grp {
>> + fsl,pins = <
>> + MX8MM_IOMUXC_UART4_RXD_UART4_DCE_RX 0x0 /* UART_C_RX */
>> + MX8MM_IOMUXC_UART4_TXD_UART4_DCE_TX 0x0 /* UART_C_TX */
>> + >;
>> + };
>> +
>> + pinctrl_usb1: usb1grp {
>> + fsl,pins = <
>> + MX8MM_IOMUXC_GPIO1_IO13_USB1_OTG_OC 0x19 /* USB_A_OC# */
>> + >;
>> + };
>> +
>> + pinctrl_usb2: usb2grp {
>> + fsl,pins = <
>> + MX8MM_IOMUXC_GPIO1_IO15_USB2_OTG_OC 0x19 /* USB_B_OC# */
>> >;
>> };
>>
>> @@ -334,6 +785,103 @@ MX8MM_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x196
>> >;
>> };
>>
>> + pinctrl_usdhc2: usdhc2grp {
>> + fsl,pins = <
>> + MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x90 /* SDIO_A_CLK */
>> + MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d0 /* SDIO_A_CMD */
>> + MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d0 /* SDIO_A_D0 */
>> + MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d0 /* SDIO_A_D1 */
>> + MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d0 /* SDIO_A_D2 */
>> + MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d0 /* SDIO_A_D3 */
>> + MX8MM_IOMUXC_SD2_WP_USDHC2_WP 0x400000d6 /* SDIO_A_WP */
>> + MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x90
>> + >;
>> + };
>> +
>> + pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
>> + fsl,pins = <
>> + MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x94 /* SDIO_A_CLK */
>> + MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4 /* SDIO_A_CMD */
>> + MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4 /* SDIO_A_D0 */
>> + MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4 /* SDIO_A_D1 */
>> + MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4 /* SDIO_A_D2 */
>> + MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4 /* SDIO_A_D3 */
>> + MX8MM_IOMUXC_SD2_WP_USDHC2_WP 0x400000d6 /* SDIO_A_WP */
>> + MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x90
>> + >;
>> + };
>> +
>> + pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
>> + fsl,pins = <
>> + MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x96 /* SDIO_A_CLK */
>> + MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d6 /* SDIO_A_CMD */
>> + MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d6 /* SDIO_A_D0 */
>> + MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d6 /* SDIO_A_D1 */
>> + MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d6 /* SDIO_A_D2 */
>> + MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d6 /* SDIO_A_D3 */
>> + MX8MM_IOMUXC_SD2_WP_USDHC2_WP 0x400000d6 /* SDIO_A_WP */
>> + MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x90
>> + >;
>> + };
>> +
>> + pinctrl_usdhc2_gpio: usdhc2gpiogrp {
>> + fsl,pins = <
>> + MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12 0x19 /* SDIO_A_CD# */
>> + >;
>> + };
>> +
>> + pinctrl_usdhc3: usdhc3grp {
>> + fsl,pins = <
>> + MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x90 /* SDIO_B_CLK */
>> + MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x90 /* SDIO_B_CMD */
>> + MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x90 /* SDIO_B_D0 */
>> + MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x90 /* SDIO_B_D1 */
>> + MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x90 /* SDIO_B_D2 */
>> + MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x90 /* SDIO_B_D3 */
>> + MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x90 /* SDIO_B_D4 */
>> + MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x90 /* SDIO_B_D5 */
>> + MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x90 /* SDIO_B_D6 */
>> + MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x90 /* SDIO_B_D7 */
>> + >;
>> + };
>> +
>> + pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
>> + fsl,pins = <
>> + MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x94 /* SDIO_B_CLK */
>> + MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x94 /* SDIO_B_CMD */
>> + MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x94 /* SDIO_B_D0 */
>> + MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x94 /* SDIO_B_D1 */
>> + MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x94 /* SDIO_B_D2 */
>> + MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x94 /* SDIO_B_D3 */
>> + MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x94 /* SDIO_B_D4 */
>> + MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x94 /* SDIO_B_D5 */
>> + MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x94 /* SDIO_B_D6 */
>> + MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x94 /* SDIO_B_D7 */
>> + >;
>> + };
>> +
>> + pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
>> + fsl,pins = <
>> + MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x96 /* SDIO_B_CLK */
>> + MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x96 /* SDIO_B_CMD */
>> + MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x96 /* SDIO_B_D0 */
>> + MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x96 /* SDIO_B_D1 */
>> + MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x96 /* SDIO_B_D2 */
>> + MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x96 /* SDIO_B_D3 */
>> + MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x96 /* SDIO_B_D4 */
>> + MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x96 /* SDIO_B_D5 */
>> + MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x96 /* SDIO_B_D6 */
>> + MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x96 /* SDIO_B_D7 */
>> + >;
>> + };
>> +
>> + pinctrl_usdhc3_gpio: usdhc3gpiogrp {
>> + fsl,pins = <
>> + MX8MM_IOMUXC_NAND_CE1_B_GPIO3_IO2 0x19 /* SDIO_B_CD# */
>> + MX8MM_IOMUXC_SAI3_MCLK_GPIO5_IO2 0x19 /* SDIO_B_WP */
>> + >;
>> + };
>> +
>> pinctrl_wdog: wdoggrp {
>> fsl,pins = <
>> MX8MM_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0xc6
>> --
>> 2.43.0
>>
