On Tue, Dec 5, 2023, at 10:45, Yoshinori Sato wrote:
> +#include <asm/addrspace.h>
> +#include "pci-sh7751.h"
> +
> +#define pcic_writel(val, base, reg) __raw_writel(val, base + (reg))
> +#define pcic_readl(base, reg) __raw_readl(base + (reg))
__raw_writel()/__raw_readl() has a number of problems with
atomicity (the compiler may split or merge pointer
dereferences), barriers and endianess. You should normally
always use readl()/writel() instead.
> + memset(pci_config, 0, sizeof(pci_config));
> + if (of_property_read_u32_array(np, "renesas,config",
> + pci_config, SH7751_NUM_CONFIG) == 0) {
> + for (i = 0; i < SH7751_NUM_CONFIG; i++) {
> + r = pci_config[i * 2];
> + /* CONFIG0 is read-only, so make it a sentinel. */
> + if (r == 0)
> + break;
> + pcic_writel(pci_config[i * 2 + 1], pcic, r * 4);
> + }
> + }
the config property seems a little too specific to this
implementation of the driver. Instead of encoding register
values in DT, I think these should either be described
in named properties where needed, or hardcoded in the driver
if there is only one sensible value.
> +/*
> + * We need to avoid collisions with `mirrored' VGA ports
> + * and other strange ISA hardware, so we always want the
> + * addresses to be allocated in the 0x000-0x0ff region
> + * modulo 0x400.
> + */
> +#define IO_REGION_BASE 0x1000
> +resource_size_t pcibios_align_resource(void *data, const struct
> resource *res,
> + resource_size_t size, resource_size_t align)
> +{
You can't have these generic functions in a driver, as that
prevents you from building more than one such driver.
The logic you have here is neither architecture nor
driver specific.
> +static int sh7751_pci_probe(struct platform_device *pdev)
> +{
> + struct resource *res, *bscres;
> + void __iomem *pcic;
> + void __iomem *bsc;
> + u32 memory[2];
> + u16 vid, did;
> + u32 word;
> +
> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> + if (IS_ERR(res))
> + return PTR_ERR(res);
> + pcic = (void __iomem *)res->start;
This cast is invalid, as res->start is a physical address
that you would need to ioremap() to turn into an __iomem
pointer.
> + bscres = platform_get_resource(pdev, IORESOURCE_MEM, 1);
> + bsc = devm_ioremap_resource(&pdev->dev, bscres);
> + if (IS_ERR(bsc))
> + return PTR_ERR(bsc);
> +
> + if (of_property_read_u32_array(pdev->dev.of_node,
> + "renesas,memory", memory, 2) < 0) {
> + /*
> + * If no memory range is specified,
> + * the entire main memory will be targeted for DMA.
> + */
> + memory[0] = memory_start;
> + memory[1] = memory_end - memory_start;
> + }
There is a generic "dma-ranges" proerty for describing
which memory is visible by a bus.
> diff --git a/drivers/pci/controller/pci-sh7751.h
> b/drivers/pci/controller/pci-sh7751.h
> new file mode 100644
> index 000000000000..540cee7095c6
> --- /dev/null
> +++ b/drivers/pci/controller/pci-sh7751.h
> @@ -0,0 +1,76 @@
If the header is only included from one file, just removed
it and add the register definitions to the driver directly.
Arnd
