This change adds a support for a 20nm qcom-ufs phy that is required in
platforms that use ufs-qcom controller.
Signed-off-by: Yaniv Gardi <ygardi@xxxxxxxxxxxxxx>
---
drivers/phy/Makefile | 1 +
drivers/phy/phy-qcom-ufs-i.h | 43 +++++-
drivers/phy/phy-qcom-ufs-qmp-20nm.c | 257 ++++++++++++++++++++++++++++++++++++
drivers/phy/phy-qcom-ufs-qmp-20nm.h | 235 +++++++++++++++++++++++++++++++++
include/linux/phy/phy-qcom-ufs.h | 59 +++++++++
5 files changed, 594 insertions(+), 1 deletion(-)
create mode 100644 drivers/phy/phy-qcom-ufs-qmp-20nm.c
create mode 100644 drivers/phy/phy-qcom-ufs-qmp-20nm.h
create mode 100644 include/linux/phy/phy-qcom-ufs.h
diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
index 335965d..781b2fa 100644
--- a/drivers/phy/Makefile
+++ b/drivers/phy/Makefile
@@ -35,3 +35,4 @@ obj-$(CONFIG_PHY_XGENE) += phy-xgene.o
obj-$(CONFIG_PHY_STIH407_USB) += phy-stih407-usb.o
obj-$(CONFIG_PHY_STIH41X_USB) += phy-stih41x-usb.o
obj-$(CONFIG_PHY_QCOM_UFS) += phy-qcom-ufs.o
+obj-$(CONFIG_PHY_QCOM_UFS) += phy-qcom-ufs-qmp-20nm.o
diff --git a/drivers/phy/phy-qcom-ufs-i.h b/drivers/phy/phy-qcom-ufs-i.h
index dac200f..591a391 100644
--- a/drivers/phy/phy-qcom-ufs-i.h
+++ b/drivers/phy/phy-qcom-ufs-i.h
@@ -15,15 +15,56 @@
#ifndef UFS_QCOM_PHY_I_H_
#define UFS_QCOM_PHY_I_H_
+#include <linux/module.h>
#include <linux/clk.h>
+#include <linux/regulator/consumer.h>
#include <linux/slab.h>
-#include <linux/phy/phy.h>
+#include <linux/phy/phy-qcom-ufs.h>
#include <linux/platform_device.h>
#include <linux/io.h>
#include <linux/delay.h>
+#define readl_poll_timeout(addr, val, cond, sleep_us, timeout_us) \
+({ \
+ ktime_t timeout = ktime_add_us(ktime_get(), timeout_us); \
+ might_sleep_if(timeout_us); \
+ for (;;) { \
+ (val) = readl(addr); \
+ if (cond) \
+ break; \
+ if (timeout_us && ktime_compare(ktime_get(), timeout) > 0) { \
+ (val) = readl(addr); \
+ break; \
+ } \
+ if (sleep_us) \
+ usleep_range(DIV_ROUND_UP(sleep_us, 4), sleep_us); \
+ } \
+ (cond) ? 0 : -ETIMEDOUT; \
+})
+
+#define UFS_QCOM_PHY_CAL_ENTRY(reg, val) \
+ { \
+ .reg_offset = reg, \
+ .cfg_value = val, \
+ }
+
#define UFS_QCOM_PHY_NAME_LEN 30
+enum {
+ MASK_SERDES_START = 0x1,
+ MASK_PCS_READY = 0x1,
+};
+
+enum {
+ OFFSET_SERDES_START = 0x0,
+};
+
+struct ufs_qcom_phy_stored_attributes {
+ u32 att;
+ u32 value;
+};
+
+
struct ufs_qcom_phy_calibration {
u32 reg_offset;
u32 cfg_value;
diff --git a/drivers/phy/phy-qcom-ufs-qmp-20nm.c b/drivers/phy/phy-qcom-ufs-qmp-20nm.c
new file mode 100644
index 0000000..8332f96
--- /dev/null
+++ b/drivers/phy/phy-qcom-ufs-qmp-20nm.c
@@ -0,0 +1,257 @@
+/*
+ * Copyright (c) 2013-2015, Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include "phy-qcom-ufs-qmp-20nm.h"
+
+#define UFS_PHY_NAME "ufs_phy_qmp_20nm"
+
+static
+int ufs_qcom_phy_qmp_20nm_phy_calibrate(struct ufs_qcom_phy *ufs_qcom_phy,
+ bool is_rate_B)
+{
+ struct ufs_qcom_phy_calibration *tbl_A, *tbl_B;
+ int tbl_size_A, tbl_size_B;
+ u8 major = ufs_qcom_phy->host_ctrl_rev_major;
+ u16 minor = ufs_qcom_phy->host_ctrl_rev_minor;
+ u16 step = ufs_qcom_phy->host_ctrl_rev_step;
+ int err;
+
+ if ((major == 0x1) && (minor == 0x002) && (step == 0x0000)) {
+ tbl_size_A = ARRAY_SIZE(phy_cal_table_rate_A_1_2_0);
+ tbl_A = phy_cal_table_rate_A_1_2_0;
+ } else if ((major == 0x1) && (minor == 0x003) && (step == 0x0000)) {
+ tbl_size_A = ARRAY_SIZE(phy_cal_table_rate_A_1_3_0);
+ tbl_A = phy_cal_table_rate_A_1_3_0;
+ } else {
+ dev_err(ufs_qcom_phy->dev, "%s: Unknown UFS-PHY version, no calibration values\n",
+ __func__);
+ err = -ENODEV;
+ goto out;
+ }
+
+ tbl_size_B = ARRAY_SIZE(phy_cal_table_rate_B);
+ tbl_B = phy_cal_table_rate_B;
+
+ err = ufs_qcom_phy_calibrate(ufs_qcom_phy, tbl_A, tbl_size_A,
+ tbl_B, tbl_size_B, is_rate_B);
+
+ if (err)
+ dev_err(ufs_qcom_phy->dev, "%s: ufs_qcom_phy_calibrate() failed %d\n",
+ __func__, err);
+
+out:
+ return err;
+}
+
+static
+void ufs_qcom_phy_qmp_20nm_advertise_quirks(struct ufs_qcom_phy *phy_common)
+{
+ phy_common->quirks =
+ UFS_QCOM_PHY_QUIRK_HIBERN8_EXIT_AFTER_PHY_PWR_COLLAPSE;
+}
+
+static int ufs_qcom_phy_qmp_20nm_init(struct phy *generic_phy)
+{
+ struct ufs_qcom_phy_qmp_20nm *phy = phy_get_drvdata(generic_phy);
+ struct ufs_qcom_phy *phy_common = &phy->common_cfg;
+ int err = 0;
+
+ err = ufs_qcom_phy_init_clks(generic_phy, phy_common);
+ if (err) {
+ dev_err(phy_common->dev, "%s: ufs_qcom_phy_init_clks() failed %d\n",
+ __func__, err);
+ goto out;
+ }
+
+ err = ufs_qcom_phy_init_vregulators(generic_phy, phy_common);
+ if (err) {
+ dev_err(phy_common->dev, "%s: ufs_qcom_phy_init_vregulators() failed %d\n",
+ __func__, err);
+ goto out;
+ }
+
+ ufs_qcom_phy_qmp_20nm_advertise_quirks(phy_common);
+
+out:
+ return err;
+}
+
+static
+void ufs_qcom_phy_qmp_20nm_power_control(struct ufs_qcom_phy *phy, bool val)
+{
+ bool hibern8_exit_after_pwr_collapse = phy->quirks &
+ UFS_QCOM_PHY_QUIRK_HIBERN8_EXIT_AFTER_PHY_PWR_COLLAPSE;
+
+ if (val) {
+ writel_relaxed(0x1, phy->mmio + UFS_PHY_POWER_DOWN_CONTROL);
+ /*
+ * Before any transactions involving PHY, ensure PHY knows
+ * that it's analog rail is powered ON.
+ */
+ mb();
+
+ if (hibern8_exit_after_pwr_collapse) {
+ /*
+ * Give atleast 1us delay after restoring PHY analog
+ * power.
+ */
+ usleep_range(1, 2);
+ writel_relaxed(0x0A, phy->mmio +
+ QSERDES_COM_SYSCLK_EN_SEL_TXBAND);
+ writel_relaxed(0x08, phy->mmio +
+ QSERDES_COM_SYSCLK_EN_SEL_TXBAND);
+ /*
+ * Make sure workaround is deactivated before proceeding
+ * with normal PHY operations.
+ */
+ mb();
+ }
+ } else {
+ if (hibern8_exit_after_pwr_collapse) {
+ writel_relaxed(0x0A, phy->mmio +
+ QSERDES_COM_SYSCLK_EN_SEL_TXBAND);
+ writel_relaxed(0x02, phy->mmio +
+ QSERDES_COM_SYSCLK_EN_SEL_TXBAND);
+ /*
+ * Make sure that above workaround is activated before
+ * PHY analog power collapse.
+ */
+ mb();
+ }
+
+ writel_relaxed(0x0, phy->mmio + UFS_PHY_POWER_DOWN_CONTROL);
+ /*
+ * ensure that PHY knows its PHY analog rail is going
+ * to be powered down
+ */
+ mb();
+ }
+}
+
+static
+void ufs_qcom_phy_qmp_20nm_set_tx_lane_enable(struct ufs_qcom_phy *phy, u32 val)
+{
+ writel_relaxed(val & UFS_PHY_TX_LANE_ENABLE_MASK,
+ phy->mmio + UFS_PHY_TX_LANE_ENABLE);
+ mb();
+}
+
+static inline void ufs_qcom_phy_qmp_20nm_start_serdes(struct ufs_qcom_phy *phy)
+{
+ u32 tmp;
+
+ tmp = readl_relaxed(phy->mmio + UFS_PHY_PHY_START);
+ tmp &= ~MASK_SERDES_START;
+ tmp |= (1 << OFFSET_SERDES_START);
+ writel_relaxed(tmp, phy->mmio + UFS_PHY_PHY_START);
+ mb();
+}
+
+static int ufs_qcom_phy_qmp_20nm_is_pcs_ready(struct ufs_qcom_phy *phy_common)
+{
+ int err = 0;
+ u32 val;
+
+ err = readl_poll_timeout(phy_common->mmio + UFS_PHY_PCS_READY_STATUS,
+ val, (val & MASK_PCS_READY), 10, 1000000);
+ if (err)
+ dev_err(phy_common->dev, "%s: poll for pcs failed err = %d\n",
+ __func__, err);
+ return err;
+}
+
+static struct phy_ops ufs_qcom_phy_qmp_20nm_phy_ops = {
+ .init = ufs_qcom_phy_qmp_20nm_init,
+ .exit = ufs_qcom_phy_exit,
+ .power_on = ufs_qcom_phy_power_on,
+ .power_off = ufs_qcom_phy_power_off,
+ .owner = THIS_MODULE,
+};
+
+static struct ufs_qcom_phy_specific_ops phy_20nm_ops = {
+ .calibrate_phy = ufs_qcom_phy_qmp_20nm_phy_calibrate,
+ .start_serdes = ufs_qcom_phy_qmp_20nm_start_serdes,
+ .is_physical_coding_sublayer_ready = ufs_qcom_phy_qmp_20nm_is_pcs_ready,
+ .set_tx_lane_enable = ufs_qcom_phy_qmp_20nm_set_tx_lane_enable,
+ .power_control = ufs_qcom_phy_qmp_20nm_power_control,
+};
+
+static int ufs_qcom_phy_qmp_20nm_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct phy *generic_phy;
+ struct ufs_qcom_phy_qmp_20nm *phy;
+ int err = 0;
+
+ phy = devm_kzalloc(dev, sizeof(*phy), GFP_KERNEL);
+ if (!phy) {
+ dev_err(dev, "%s: failed to allocate phy\n", __func__);
+ err = -ENOMEM;
+ goto out;
+ }
+
+ generic_phy = ufs_qcom_phy_generic_probe(pdev, &phy->common_cfg,
+ &ufs_qcom_phy_qmp_20nm_phy_ops, &phy_20nm_ops);
+
+ if (!generic_phy) {
+ dev_err(dev, "%s: ufs_qcom_phy_generic_probe() failed\n",
+ __func__);
+ err = -EIO;
+ goto out;
+ }
+
+ phy_set_drvdata(generic_phy, phy);
+
+ strlcpy(phy->common_cfg.name, UFS_PHY_NAME,
+ sizeof(phy->common_cfg.name));
+
+out:
+ return err;
+}
+
+static int ufs_qcom_phy_qmp_20nm_remove(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct phy *generic_phy = to_phy(dev);
+ struct ufs_qcom_phy *ufs_qcom_phy = get_ufs_qcom_phy(generic_phy);
+ int err = 0;
+
+ err = ufs_qcom_phy_remove(generic_phy, ufs_qcom_phy);
+ if (err)
+ dev_err(dev, "%s: ufs_qcom_phy_remove failed = %d\n",
+ __func__, err);
+
+ return err;
+}
+
+static const struct of_device_id ufs_qcom_phy_qmp_20nm_of_match[] = {
+ {.compatible = "qcom,ufs-phy-qmp-20nm"},
+ {},
+};
+MODULE_DEVICE_TABLE(of, ufs_qcom_phy_qmp_20nm_of_match);
+
+static struct platform_driver ufs_qcom_phy_qmp_20nm_driver = {
+ .probe = ufs_qcom_phy_qmp_20nm_probe,
+ .remove = ufs_qcom_phy_qmp_20nm_remove,
+ .driver = {
+ .of_match_table = ufs_qcom_phy_qmp_20nm_of_match,
+ .name = "ufs_qcom_phy_qmp_20nm",
+ .owner = THIS_MODULE,
+ },
+};
+
+module_platform_driver(ufs_qcom_phy_qmp_20nm_driver);
+
+MODULE_DESCRIPTION("Universal Flash Storage (UFS) QCOM PHY QMP 20nm");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/phy/phy-qcom-ufs-qmp-20nm.h b/drivers/phy/phy-qcom-ufs-qmp-20nm.h
new file mode 100644
index 0000000..4f3076b
--- /dev/null
+++ b/drivers/phy/phy-qcom-ufs-qmp-20nm.h
@@ -0,0 +1,235 @@
+/*
+ * Copyright (c) 2013-2015, Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#ifndef UFS_QCOM_PHY_QMP_20NM_H_
+#define UFS_QCOM_PHY_QMP_20NM_H_
+
+#include "phy-qcom-ufs-i.h"
+
+/* QCOM UFS PHY control registers */
+
+#define COM_OFF(x) (0x000 + x)
+#define PHY_OFF(x) (0xC00 + x)
+#define TX_OFF(n, x) (0x400 + (0x400 * n) + x)
+#define RX_OFF(n, x) (0x600 + (0x400 * n) + x)
+
+/* UFS PHY PLL block registers */
+#define QSERDES_COM_SYS_CLK_CTRL COM_OFF(0x0)
+#define QSERDES_COM_PLL_VCOTAIL_EN COM_OFF(0x04)
+#define QSERDES_COM_PLL_CNTRL COM_OFF(0x14)
+#define QSERDES_COM_PLL_IP_SETI COM_OFF(0x24)
+#define QSERDES_COM_CORE_CLK_IN_SYNC_SEL COM_OFF(0x28)
+#define QSERDES_COM_BIAS_EN_CLKBUFLR_EN COM_OFF(0x30)
+#define QSERDES_COM_PLL_CP_SETI COM_OFF(0x34)
+#define QSERDES_COM_PLL_IP_SETP COM_OFF(0x38)
+#define QSERDES_COM_PLL_CP_SETP COM_OFF(0x3C)
+#define QSERDES_COM_SYSCLK_EN_SEL_TXBAND COM_OFF(0x48)
+#define QSERDES_COM_RESETSM_CNTRL COM_OFF(0x4C)
+#define QSERDES_COM_RESETSM_CNTRL2 COM_OFF(0x50)
+#define QSERDES_COM_PLLLOCK_CMP1 COM_OFF(0x90)
+#define QSERDES_COM_PLLLOCK_CMP2 COM_OFF(0x94)
+#define QSERDES_COM_PLLLOCK_CMP3 COM_OFF(0x98)
+#define QSERDES_COM_PLLLOCK_CMP_EN COM_OFF(0x9C)
+#define QSERDES_COM_BGTC COM_OFF(0xA0)
+#define QSERDES_COM_DEC_START1 COM_OFF(0xAC)
+#define QSERDES_COM_PLL_AMP_OS COM_OFF(0xB0)
+#define QSERDES_COM_RES_CODE_UP_OFFSET COM_OFF(0xD8)
+#define QSERDES_COM_RES_CODE_DN_OFFSET COM_OFF(0xDC)
+#define QSERDES_COM_DIV_FRAC_START1 COM_OFF(0x100)
+#define QSERDES_COM_DIV_FRAC_START2 COM_OFF(0x104)
+#define QSERDES_COM_DIV_FRAC_START3 COM_OFF(0x108)
+#define QSERDES_COM_DEC_START2 COM_OFF(0x10C)
+#define QSERDES_COM_PLL_RXTXEPCLK_EN COM_OFF(0x110)
+#define QSERDES_COM_PLL_CRCTRL COM_OFF(0x114)
+#define QSERDES_COM_PLL_CLKEPDIV COM_OFF(0x118)
+
+/* TX LANE n (0, 1) registers */
+#define QSERDES_TX_EMP_POST1_LVL(n) TX_OFF(n, 0x08)
+#define QSERDES_TX_DRV_LVL(n) TX_OFF(n, 0x0C)
+#define QSERDES_TX_LANE_MODE(n) TX_OFF(n, 0x54)
+
+/* RX LANE n (0, 1) registers */
+#define QSERDES_RX_CDR_CONTROL1(n) RX_OFF(n, 0x0)
+#define QSERDES_RX_CDR_CONTROL_HALF(n) RX_OFF(n, 0x8)
+#define QSERDES_RX_RX_EQ_GAIN1_LSB(n) RX_OFF(n, 0xA8)
+#define QSERDES_RX_RX_EQ_GAIN1_MSB(n) RX_OFF(n, 0xAC)
+#define QSERDES_RX_RX_EQ_GAIN2_LSB(n) RX_OFF(n, 0xB0)
+#define QSERDES_RX_RX_EQ_GAIN2_MSB(n) RX_OFF(n, 0xB4)
+#define QSERDES_RX_RX_EQU_ADAPTOR_CNTRL2(n) RX_OFF(n, 0xBC)
+#define QSERDES_RX_CDR_CONTROL_QUARTER(n) RX_OFF(n, 0xC)
+#define QSERDES_RX_SIGDET_CNTRL(n) RX_OFF(n, 0x100)
+
+/* UFS PHY registers */
+#define UFS_PHY_PHY_START PHY_OFF(0x00)
+#define UFS_PHY_POWER_DOWN_CONTROL PHY_OFF(0x4)
+#define UFS_PHY_TX_LANE_ENABLE PHY_OFF(0x44)
+#define UFS_PHY_PWM_G1_CLK_DIVIDER PHY_OFF(0x08)
+#define UFS_PHY_PWM_G2_CLK_DIVIDER PHY_OFF(0x0C)
+#define UFS_PHY_PWM_G3_CLK_DIVIDER PHY_OFF(0x10)
+#define UFS_PHY_PWM_G4_CLK_DIVIDER PHY_OFF(0x14)
+#define UFS_PHY_CORECLK_PWM_G1_CLK_DIVIDER PHY_OFF(0x34)
+#define UFS_PHY_CORECLK_PWM_G2_CLK_DIVIDER PHY_OFF(0x38)
+#define UFS_PHY_CORECLK_PWM_G3_CLK_DIVIDER PHY_OFF(0x3C)
+#define UFS_PHY_CORECLK_PWM_G4_CLK_DIVIDER PHY_OFF(0x40)
+#define UFS_PHY_OMC_STATUS_RDVAL PHY_OFF(0x68)
+#define UFS_PHY_LINE_RESET_TIME PHY_OFF(0x28)
+#define UFS_PHY_LINE_RESET_GRANULARITY PHY_OFF(0x2C)
+#define UFS_PHY_TSYNC_RSYNC_CNTL PHY_OFF(0x48)
+#define UFS_PHY_PLL_CNTL PHY_OFF(0x50)
+#define UFS_PHY_TX_LARGE_AMP_DRV_LVL PHY_OFF(0x54)
+#define UFS_PHY_TX_SMALL_AMP_DRV_LVL PHY_OFF(0x5C)
+#define UFS_PHY_TX_LARGE_AMP_POST_EMP_LVL PHY_OFF(0x58)
+#define UFS_PHY_TX_SMALL_AMP_POST_EMP_LVL PHY_OFF(0x60)
+#define UFS_PHY_CFG_CHANGE_CNT_VAL PHY_OFF(0x64)
+#define UFS_PHY_RX_SYNC_WAIT_TIME PHY_OFF(0x6C)
+#define UFS_PHY_TX_MIN_SLEEP_NOCONFIG_TIME_CAPABILITY PHY_OFF(0xB4)
+#define UFS_PHY_RX_MIN_SLEEP_NOCONFIG_TIME_CAPABILITY PHY_OFF(0xE0)
+#define UFS_PHY_TX_MIN_STALL_NOCONFIG_TIME_CAPABILITY PHY_OFF(0xB8)
+#define UFS_PHY_RX_MIN_STALL_NOCONFIG_TIME_CAPABILITY PHY_OFF(0xE4)
+#define UFS_PHY_TX_MIN_SAVE_CONFIG_TIME_CAPABILITY PHY_OFF(0xBC)
+#define UFS_PHY_RX_MIN_SAVE_CONFIG_TIME_CAPABILITY PHY_OFF(0xE8)
+#define UFS_PHY_RX_PWM_BURST_CLOSURE_LENGTH_CAPABILITY PHY_OFF(0xFC)
+#define UFS_PHY_RX_MIN_ACTIVATETIME_CAPABILITY PHY_OFF(0x100)
+#define UFS_PHY_RX_SIGDET_CTRL3 PHY_OFF(0x14c)
+#define UFS_PHY_RMMI_ATTR_CTRL PHY_OFF(0x160)
+#define UFS_PHY_RMMI_RX_CFGUPDT_L1 (1 << 7)
+#define UFS_PHY_RMMI_TX_CFGUPDT_L1 (1 << 6)
+#define UFS_PHY_RMMI_CFGWR_L1 (1 << 5)
+#define UFS_PHY_RMMI_CFGRD_L1 (1 << 4)
+#define UFS_PHY_RMMI_RX_CFGUPDT_L0 (1 << 3)
+#define UFS_PHY_RMMI_TX_CFGUPDT_L0 (1 << 2)
+#define UFS_PHY_RMMI_CFGWR_L0 (1 << 1)
+#define UFS_PHY_RMMI_CFGRD_L0 (1 << 0)
+#define UFS_PHY_RMMI_ATTRID PHY_OFF(0x164)
+#define UFS_PHY_RMMI_ATTRWRVAL PHY_OFF(0x168)
+#define UFS_PHY_RMMI_ATTRRDVAL_L0_STATUS PHY_OFF(0x16C)
+#define UFS_PHY_RMMI_ATTRRDVAL_L1_STATUS PHY_OFF(0x170)
+#define UFS_PHY_PCS_READY_STATUS PHY_OFF(0x174)
+
+#define UFS_PHY_TX_LANE_ENABLE_MASK 0x3
+
+/*
+ * This structure represents the 20nm specific phy.
+ * common_cfg MUST remain the first field in this structure
+ * in case extra fields are added. This way, when calling
+ * get_ufs_qcom_phy() of generic phy, we can extract the
+ * common phy structure (struct ufs_qcom_phy) out of it
+ * regardless of the relevant specific phy.
+ */
+struct ufs_qcom_phy_qmp_20nm {
+ struct ufs_qcom_phy common_cfg;
+};
+
+static struct ufs_qcom_phy_calibration phy_cal_table_rate_A_1_2_0[] = {
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_POWER_DOWN_CONTROL, 0x01),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RX_SIGDET_CTRL3, 0x0D),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_VCOTAIL_EN, 0xe1),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CRCTRL, 0xcc),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_SYSCLK_EN_SEL_TXBAND, 0x08),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CLKEPDIV, 0x03),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_RXTXEPCLK_EN, 0x10),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DEC_START1, 0x82),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DEC_START2, 0x03),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START1, 0x80),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START2, 0x80),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START3, 0x40),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP1, 0xff),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP2, 0x19),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP3, 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP_EN, 0x03),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_RESETSM_CNTRL, 0x90),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_RESETSM_CNTRL2, 0x03),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL1(0), 0xf2),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_HALF(0), 0x0c),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_QUARTER(0), 0x12),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL1(1), 0xf2),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_HALF(1), 0x0c),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_QUARTER(1), 0x12),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN1_LSB(0), 0xff),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN1_MSB(0), 0xff),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN2_LSB(0), 0xff),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN2_MSB(0), 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN1_LSB(1), 0xff),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN1_MSB(1), 0xff),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN2_LSB(1), 0xff),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN2_MSB(1), 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CP_SETI, 0x3f),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_IP_SETP, 0x1b),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CP_SETP, 0x0f),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_IP_SETI, 0x01),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_EMP_POST1_LVL(0), 0x2F),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_DRV_LVL(0), 0x20),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_EMP_POST1_LVL(1), 0x2F),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_DRV_LVL(1), 0x20),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_LANE_MODE(0), 0x68),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_LANE_MODE(1), 0x68),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL2(1), 0xdc),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL2(0), 0xdc),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_BIAS_EN_CLKBUFLR_EN, 0x3),
+};
+
+static struct ufs_qcom_phy_calibration phy_cal_table_rate_A_1_3_0[] = {
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_POWER_DOWN_CONTROL, 0x01),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RX_SIGDET_CTRL3, 0x0D),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_VCOTAIL_EN, 0xe1),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CRCTRL, 0xcc),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_SYSCLK_EN_SEL_TXBAND, 0x08),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CLKEPDIV, 0x03),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_RXTXEPCLK_EN, 0x10),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DEC_START1, 0x82),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DEC_START2, 0x03),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START1, 0x80),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START2, 0x80),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START3, 0x40),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP1, 0xff),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP2, 0x19),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP3, 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP_EN, 0x03),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_RESETSM_CNTRL, 0x90),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_RESETSM_CNTRL2, 0x03),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL1(0), 0xf2),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_HALF(0), 0x0c),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_QUARTER(0), 0x12),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL1(1), 0xf2),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_HALF(1), 0x0c),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_QUARTER(1), 0x12),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN1_LSB(0), 0xff),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN1_MSB(0), 0xff),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN2_LSB(0), 0xff),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN2_MSB(0), 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN1_LSB(1), 0xff),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN1_MSB(1), 0xff),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN2_LSB(1), 0xff),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN2_MSB(1), 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CP_SETI, 0x2b),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_IP_SETP, 0x38),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CP_SETP, 0x3c),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_RES_CODE_UP_OFFSET, 0x02),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_RES_CODE_DN_OFFSET, 0x02),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_IP_SETI, 0x01),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CNTRL, 0x40),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_LANE_MODE(0), 0x68),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_LANE_MODE(1), 0x68),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL2(1), 0xdc),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL2(0), 0xdc),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_BIAS_EN_CLKBUFLR_EN, 0x3),
+};
+
+static struct ufs_qcom_phy_calibration phy_cal_table_rate_B[] = {
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DEC_START1, 0x98),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP1, 0x65),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP2, 0x1e),
+};
+
+#endif
diff --git a/include/linux/phy/phy-qcom-ufs.h b/include/linux/phy/phy-qcom-ufs.h
new file mode 100644
index 0000000..9d18e9f
--- /dev/null
+++ b/include/linux/phy/phy-qcom-ufs.h
@@ -0,0 +1,59 @@
+/*
+ * Copyright (c) 2013-2015, Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#ifndef PHY_QCOM_UFS_H_
+#define PHY_QCOM_UFS_H_
+
+#include "phy.h"
+
+/**
+ * ufs_qcom_phy_enable_ref_clk() - Enable the phy
+ * ref clock.
+ * @phy: reference to a generic phy
+ *
+ * returns 0 for success, and non-zero for error.
+ */
+int ufs_qcom_phy_enable_ref_clk(struct phy *phy);
+
+/**
+ * ufs_qcom_phy_disable_ref_clk() - Disable the phy
+ * ref clock.
+ * @phy: reference to a generic phy.
+ */
+void ufs_qcom_phy_disable_ref_clk(struct phy *phy);
+
+/**
+ * ufs_qcom_phy_enable_dev_ref_clk() - Enable the device
+ * ref clock.
+ * @phy: reference to a generic phy.
+ */
+void ufs_qcom_phy_enable_dev_ref_clk(struct phy *phy);
+
+/**
+ * ufs_qcom_phy_disable_dev_ref_clk() - Disable the device
+ * ref clock.
+ * @phy: reference to a generic phy.
+ */
+void ufs_qcom_phy_disable_dev_ref_clk(struct phy *phy);
+
+int ufs_qcom_phy_enable_iface_clk(struct phy *phy);
+void ufs_qcom_phy_disable_iface_clk(struct phy *phy);
+int ufs_qcom_phy_start_serdes(struct phy *phy);
+int ufs_qcom_phy_set_tx_lane_enable(struct phy *phy, u32 tx_lanes);
+int ufs_qcom_phy_calibrate_phy(struct phy *phy, bool is_rate_B);
+int ufs_qcom_phy_is_pcs_ready(struct phy *phy);
+void ufs_qcom_phy_save_controller_version(struct phy *phy,
+ u8 major, u16 minor, u16 step);
+
+#endif /* PHY_QCOM_UFS_H_ */
--
1.8.5.2
--
QUALCOMM ISRAEL, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
