On Fri, 1 Dec 2023 23:16:51 -0500 Abdel Alkuor <alkuor@xxxxxxxxx> wrote: > as6200 is a high accuracy temperature sensor of 0.0625C with a range > between -40 to 125 Celsius degrees. > > The driver implements the alert trigger event in comparator mode where > consecutive faults are converted into periods, high/low temperature > thresholds require to be above/below the set limit for n seconds for > the alert to be triggered/cleared. The alert is only cleared when the > current temperature is below the low temperature threshold for n seconds. > > The driver supports the following: > - show available sampling frequencey > - read/write sampling frequency > - read raw temperature > - read scaling factor > - read/write temperature period that needs to be met for low/high > temperature thresholds to trigger an alert > - show available temperature period thresholds > - buffer trigger > - temperature alert event trigger Hi Abdel, A few comments inline. Looking good in general. > > Datasheet: https://ams.com/documents/20143/36005/AS6200_DS000449_4-00.pdf > No blank line here. Tags block (and Datasheet is a tag) never has blank lines as that breaks some existing tooling. > Signed-off-by: Abdel Alkuor <alkuor@xxxxxxxxx> > > What: /sys/bus/iio/devices/iio:deviceX/in_filter_notch_center_frequency > diff --git a/drivers/iio/temperature/Kconfig b/drivers/iio/temperature/Kconfig > index ed384f33e0c7..a0ffbc77e623 100644 > --- a/drivers/iio/temperature/Kconfig > +++ b/drivers/iio/temperature/Kconfig > @@ -4,6 +4,17 @@ > # > menu "Temperature sensors" > > +config AS6200 > + tristate "AS6200 temperature sensor" > + depends on I2C > + select REGMAP_I2C > + help > + If you say yes here you get support for AS6200 > + temperature sensor chip connected via I2C. > + > + This driver can also be built as a module. If so, the module > + will be called as6200. > + > config IQS620AT_TEMP > tristate "Azoteq IQS620AT temperature sensor" > depends on MFD_IQS62X || COMPILE_TEST > @@ -157,5 +168,4 @@ config MAX31865 > > This driver can also be build as a module. If so, the module > will be called max31865. > - Stray change. > endmenu > diff --git a/drivers/iio/temperature/as6200.c b/drivers/iio/temperature/as6200.c > new file mode 100644 > index 000000000000..7fcc785871d8 > --- /dev/null > +++ b/drivers/iio/temperature/as6200.c > @@ -0,0 +1,493 @@ > +// SPDX-License-Identifier: GPL-2.0 > +/* > + * Driver for AMS AS6200 Temperature sensor > + * > + * Author: Abdel Alkuor <alkuor@xxxxxxxxx> > + */ > + > +#include <linux/bitfield.h> > +#include <linux/device.h> > +#include <linux/i2c.h> > +#include <linux/interrupt.h> > +#include <linux/kstrtox.h> > +#include <linux/module.h> > +#include <linux/regmap.h> > + > +#include <linux/iio/buffer.h> > +#include <linux/iio/events.h> > +#include <linux/iio/iio.h> > +#include <linux/iio/sysfs.h> > +#include <linux/iio/trigger.h> > +#include <linux/iio/triggered_buffer.h> > +#include <linux/iio/trigger_consumer.h> > + > +#define AS6200_TVAL_REG 0x0 > +#define AS6200_CONFIG_REG 0x1 > +#define AS6200_TLOW_REG 0x2 > +#define AS6200_THIGH_REG 0x3 > + > +#define AS6200_CONFIG_AL BIT(5) > +#define AS6200_CONFIG_CR GENMASK(7, 6) > +#define AS6200_CONFIG_SM BIT(8) > +#define AS6200_CONFIG_IM BIT(9) > +#define AS6200_CONFIG_POL BIT(10) > +#define AS6200_CONFIG_CF GENMASK(12, 11) > + > +#define AS6200_TEMP_MASK GENMASK(15, 4) > + > +struct as6200 { > + struct regmap *regmap; > + struct mutex lock; /* Prevent concurrent temp fault processing */ Why does it matter? What might cause such processing? > +}; > + > +static const int as6200_samp_freq[4][2] = { > + { 0, 250000 }, > + { 1, 0 }, > + { 4, 0 }, > + { 8, 0 } > +}; > + > +/* Consective faults converted to period */ > +static const int as6200_temp_thresh_periods[4][4][2] = { > + { { 4, 0 }, { 8, 0 }, { 16, 0 }, { 24, 0 } }, > + { { 1, 0 }, { 2, 0 }, { 4, 0 }, { 6, 0 } }, > + { { 0, 250000 }, { 0, 500000 }, { 1, 0 }, { 2, 0} }, > + { { 0, 125000 }, { 0, 250000 }, { 0, 500000 }, { 0, 750000 } } I'd suggest naming the first column at least (which is CR I think?) So define an enum and enum { AS6200_CR_0_25HZ = 0, AS6200_CR_1HZ = 1, AS6200_CR_4HZ = 2, AS6200_CR_8HZ = 3, }; And use that for the samp freq entries above, so that they clearly relate to the rows of this arram [AS6200_CR_0_25HZ] = { { 4, 0 }, { 8, 0 }, { 16, 0 }, { 24, 0 } }, You could take it further and use an enum for CF as well. [AS6200_CR_0_25HZ] = { [AS6200_CF_1] = { 4, 0 }, [AS6200_CF_2] = { 8, 0 }, [AS6200_CF_4] = { 16, 0 }, [AS6200_CF_6] = { 24, 0 }, }, [AS6200_CR_1_HZ] = { [AS6200_CF_1] = { 1, 0 }, [AS6200_CF_2] = { 2, 0 }, ... } etc which makes it clear where all the numbers come. > +}; > +static int as6200_read_event_value(struct iio_dev *indio_dev, > + const struct iio_chan_spec *chan, > + enum iio_event_type type, > + enum iio_event_direction dir, > + enum iio_event_info info, > + int *val, int *val2) > +{ > + struct as6200 *as = iio_priv(indio_dev); > + unsigned int reg; > + unsigned int tmp; > + int ret; > + u8 cf; > + u8 cr; > + > + switch (dir) { > + case IIO_EV_DIR_FALLING: > + reg = AS6200_TLOW_REG; > + break; > + case IIO_EV_DIR_RISING: > + reg = AS6200_THIGH_REG; > + break; > + case IIO_EV_DIR_EITHER: > + reg = AS6200_CONFIG_REG; > + break; > + default: > + return -EINVAL; > + } > + > + ret = regmap_read(as->regmap, reg, &tmp); > + if (ret) > + return ret; > + > + if (info == IIO_EV_INFO_VALUE) { > + *val = sign_extend32(FIELD_GET(AS6200_TEMP_MASK, tmp), 11); > + ret = IIO_VAL_INT; return here. > + } else { > + cf = FIELD_GET(AS6200_CONFIG_CF, tmp); > + cr = FIELD_GET(AS6200_CONFIG_CR, tmp); > + *val = as6200_temp_thresh_periods[cr][cf][0]; > + *val2 = as6200_temp_thresh_periods[cr][cf][1]; > + ret = IIO_VAL_INT_PLUS_MICRO; and here. If there is nothing more to be done, it simplifies the code flow being read to just return as quick as possible. > + } > + > + return ret; > +} > +static irqreturn_t as6200_event_handler(int irq, void *private) > +{ > + struct iio_dev *indio_dev = private; > + struct as6200 *as = iio_priv(indio_dev); > + unsigned int alert; > + enum iio_event_direction dir; > + int ret; > + > + guard(mutex)(&as->lock); What data are we protecting here? > + > + ret = regmap_read(as->regmap, AS6200_CONFIG_REG, &alert); > + if (ret) > + return IRQ_NONE; > + > + alert = FIELD_GET(AS6200_CONFIG_AL, alert); > + > + dir = alert ? IIO_EV_DIR_FALLING : IIO_EV_DIR_RISING; > + > + iio_push_event(indio_dev, > + IIO_EVENT_CODE(IIO_TEMP, 0, 0, > + dir, > + IIO_EV_TYPE_THRESH, > + 0, 0, 0), > + iio_get_time_ns(indio_dev)); > + > + return IRQ_HANDLED; > +} > + > +static irqreturn_t as6200_trigger_handler(int irq, void *private) > +{ > + struct iio_poll_func *pf = private; > + struct iio_dev *indio_dev = pf->indio_dev; > + struct as6200 *as = iio_priv(indio_dev); > + int ret; > + u8 data[16]; I'd make this much more explicit and make sure you zero it to avoid leaking data. struct data { u8 channel; s64 timestamp __aligned(8); }; memset(&data, 0, sizeof(data)); /* Ensures the holes are zero filled */ Also, avoid the casting mess and read into a local variable that is an unsigned int and copy it to the struct data if no error. > + > + ret = regmap_read(as->regmap, AS6200_TVAL_REG, (unsigned int *)data); > + if (!ret) Whilst it's more lines, greatly prefer to see error paths out of line and good paths inline (so no if (!ret)) if (ret) goto done; iio_push... done: ... May seem silly but when reviewing a lot of code, keeping things looking "normal" is a great benefit! > + iio_push_to_buffers_with_timestamp(indio_dev, data, > + iio_get_time_ns(indio_dev)); > + > + iio_trigger_notify_done(indio_dev->trig); > + > + return IRQ_HANDLED; > +} ... > + > +static int __maybe_unused as6200_suspend(struct device *dev) > +{ > + struct i2c_client *client = to_i2c_client(dev); > + struct as6200 *as = iio_priv(i2c_get_clientdata(client)); > + > + if (client->irq) > + disable_irq(client->irq); > + > + return regmap_update_bits(as->regmap, AS6200_CONFIG_REG, > + AS6200_CONFIG_SM, AS6200_CONFIG_SM); > +} > + > +static int __maybe_unused as6200_resume(struct device *dev) > +{ > + struct i2c_client *client = to_i2c_client(dev); > + struct as6200 *as = iio_priv(i2c_get_clientdata(client)); > + > + if (client->irq) > + enable_irq(client->irq); I would normally expect suspend and resume to be mirror images. If that doesn't make sense for some reason and we do need to do the irq handling before the register write in both cases then add a comment. > + > + return regmap_update_bits(as->regmap, AS6200_CONFIG_REG, > + AS6200_CONFIG_SM, 0); > +} > + > +static const struct dev_pm_ops as6200_pm_ops = { DEFINE_SIMPLE_DEV_PM_OPS() > + SET_SYSTEM_SLEEP_PM_OPS(as6200_suspend, as6200_resume) > +}; > + > +static const struct i2c_device_id as6200_id_table[] = { > + { "as6200" }, > + { } > +}; > +MODULE_DEVICE_TABLE(i2c, as6200_id_table); > + > +static const struct of_device_id as6200_of_match[] = { > + { .compatible = "ams,as6200" }, > + { } > +}; > +MODULE_DEVICE_TABLE(of, as6200_of_match); > + > +static struct i2c_driver as6200_driver = { > + .driver = { > + .name = "as6200", > + .pm = pm_sleep_ptr(&as6200_pm_ops), > + .of_match_table = as6200_of_match, > + }, > + .probe = as6200_probe, > + .id_table = as6200_id_table, > +}; > +module_i2c_driver(as6200_driver); > + > +MODULE_AUTHOR("Abdel Alkuor <alkuor@xxxxxxxxx"); > +MODULE_DESCRIPTION("AMS AS6200 Temperature Sensor"); > +MODULE_LICENSE("GPL");
