Hi Neha,
On 11:22-20231128, Neha Malcom Francis wrote:
> This patch adds support for TPS6594 PMIC on wkup I2C0 bus. This device
> provides regulators (bucks and LDOs), but also GPIOs, a RTC, a watchdog,
> an ESM (Error Signal Monitor) which monitors the SoC error output
> signal, and a PFSM (Pre-configurable Finite State Machine) which manages
> the operational modes of the PMIC.
>
> Signed-off-by: Neha Malcom Francis <n-francis@xxxxxx>
> ---
> arch/arm64/boot/dts/ti/k3-am69-sk.dts | 100 ++++++++++++++++++++++++++
> 1 file changed, 100 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/ti/k3-am69-sk.dts b/arch/arm64/boot/dts/ti/k3-am69-sk.dts
> index 9868c7049bfb..dec27acb4e96 100644
> --- a/arch/arm64/boot/dts/ti/k3-am69-sk.dts
> +++ b/arch/arm64/boot/dts/ti/k3-am69-sk.dts
> @@ -431,6 +431,17 @@ J784S4_IOPAD(0x000, PIN_INPUT, 7) /* (AN35) EXTINTN.GPIO0_0 */
> };
> };
>
> +&wkup_pmx1 {
> + status = "okay";
> +
> + pmic_irq_pins_default: pmic-irq-default-pins {
> + pinctrl-single,pins = <
> + /* (AA37) MCU_ADC1_AIN4.WKUP_GPIO0_83 */
> + J784S4_WKUP_IOPAD(0x12c, PIN_INPUT, 7)
> + >;
> + };
> +};
> +
> &wkup_pmx2 {
> bootph-all;
> wkup_uart0_pins_default: wkup-uart0-default-pins {
> @@ -631,6 +642,95 @@ eeprom@51 {
> compatible = "atmel,24c512";
> reg = <0x51>;
> };
> +
> + tps659413: pmic@48 {
> + compatible = "ti,tps6594-q1";
> + reg = <0x48>;
> + system-power-controller;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pmic_irq_pins_default>;
> + interrupt-parent = <&wkup_gpio0>;
> + interrupts = <39 IRQ_TYPE_EDGE_FALLING>;
> + ti,primary-pmic;
> +
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + buck12-supply = <&vsys_3v3>;
> + buck3-supply = <&vsys_3v3>;
> + buck4-supply = <&vsys_3v3>;
> + buck5-supply = <&vsys_3v3>;
> + ldo1-supply = <&vsys_3v3>;
> + ldo2-supply = <&vsys_3v3>;
> + ldo3-supply = <&vsys_3v3>;
> + ldo4-supply = <&vsys_3v3>;
> +
> + regulators {
> + bucka12: buck12 {
> + regulator-name = "vdd_ddr_1v1";
> + regulator-min-microvolt = <1100000>;
> + regulator-max-microvolt = <1100000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + bucka3: buck3 {
> + regulator-name = "vdd_ram_0v85";
> + regulator-min-microvolt = <850000>;
> + regulator-max-microvolt = <850000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + bucka4: buck4 {
> + regulator-name = "vdd_io_1v8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + bucka5: buck5 {
> + regulator-name = "vdd_mcu_0v85";
> + regulator-min-microvolt = <850000>;
> + regulator-max-microvolt = <850000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + ldoa1: ldo1 {
> + regulator-name = "vdd_mcuio_1v8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + ldoa2: ldo2 {
> + regulator-name = "vdd_mcuio_3v3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + ldoa3: ldo3 {
> + regulator-name = "vds_dll_0v8";
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <800000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + ldoa4: ldo4 {
> + regulator-name = "vda_mcu_1v8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> + };
> + };
> };
>
With the full series applied:
https://gist.github.com/manorit2001/7e794a7cbf58af4d7fbbee03eac88e86
[ For AM69-SK ]
Tested-by: Manorit Chawdhry <m-chawdhry@xxxxxx>
Regards,
Manorit
> &wkup_gpio0 {
> --
> 2.34.1
>
