Now interconnect dependent devices are added in sm8650 DTSI,
now enable more devices for the Qualcomm SM8650 MTP board:
- PCIe
- Display
- DSPs
- SDCard
- UFS
- USB role switch with PMIC Glink
Reviewed-by: Konrad Dybcio <konrad.dybcio@xxxxxxxxxx>
Signed-off-by: Neil Armstrong <neil.armstrong@xxxxxxxxxx>
---
arch/arm64/boot/dts/qcom/sm8650-mtp.dts | 235 +++++++++++++++++++++++++++++++-
1 file changed, 234 insertions(+), 1 deletion(-)
diff --git a/arch/arm64/boot/dts/qcom/sm8650-mtp.dts b/arch/arm64/boot/dts/qcom/sm8650-mtp.dts
index 51092d20d610..656cdbc6f234 100644
--- a/arch/arm64/boot/dts/qcom/sm8650-mtp.dts
+++ b/arch/arm64/boot/dts/qcom/sm8650-mtp.dts
@@ -28,6 +28,44 @@ chosen {
stdout-path = "serial0:115200n8";
};
+ pmic-glink {
+ compatible = "qcom,sm8650-pmic-glink",
+ "qcom,sm8550-pmic-glink",
+ "qcom,pmic-glink";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ orientation-gpios = <&tlmm 29 GPIO_ACTIVE_HIGH>;
+
+ connector@0 {
+ compatible = "usb-c-connector";
+ reg = <0>;
+
+ power-role = "dual";
+ data-role = "dual";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ pmic_glink_hs_in: endpoint {
+ remote-endpoint = <&usb_1_dwc3_hs>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ pmic_glink_ss_in: endpoint {
+ remote-endpoint = <&usb_1_dwc3_ss>;
+ };
+ };
+ };
+ };
+ };
+
vph_pwr: vph-pwr-regulator {
compatible = "regulator-fixed";
@@ -77,6 +115,9 @@ vreg_l2b_3p0: ldo2 {
regulator-min-microvolt = <3008000>;
regulator-max-microvolt = <3008000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
};
vreg_l5b_3p1: ldo5 {
@@ -389,6 +430,106 @@ vreg_l3i_1p2: ldo3 {
};
};
+&dispcc {
+ status = "okay";
+};
+
+&mdss {
+ status = "okay";
+};
+
+&mdss_dsi0 {
+ vdda-supply = <&vreg_l3i_1p2>;
+
+ status = "okay";
+
+ panel@0 {
+ compatible = "visionox,vtdr6130";
+ reg = <0>;
+
+ reset-gpios = <&tlmm 133 GPIO_ACTIVE_LOW>;
+
+ vddio-supply = <&vreg_l12b_1p8>;
+ vci-supply = <&vreg_l13b_3p0>;
+ vdd-supply = <&vreg_l11b_1p2>;
+
+ pinctrl-0 = <&disp0_reset_n_active>, <&mdp_vsync_active>;
+ pinctrl-1 = <&disp0_reset_n_suspend>, <&mdp_vsync_suspend>;
+ pinctrl-names = "default", "sleep";
+
+ port {
+ panel0_in: endpoint {
+ remote-endpoint = <&mdss_dsi0_out>;
+ };
+ };
+ };
+};
+
+&mdss_dsi0_out {
+ remote-endpoint = <&panel0_in>;
+ data-lanes = <0 1 2 3>;
+};
+
+&mdss_dsi0_phy {
+ vdds-supply = <&vreg_l1i_0p88>;
+
+ status = "okay";
+};
+
+&mdss_mdp {
+ status = "okay";
+};
+
+&pcie_1_phy_aux_clk {
+ clock-frequency = <1000>;
+};
+
+&pcie0 {
+ wake-gpios = <&tlmm 96 GPIO_ACTIVE_HIGH>;
+ perst-gpios = <&tlmm 94 GPIO_ACTIVE_LOW>;
+
+ pinctrl-0 = <&pcie0_default_state>;
+ pinctrl-names = "default";
+
+ status = "okay";
+};
+
+&pcie0_phy {
+ vdda-phy-supply = <&vreg_l1i_0p88>;
+ vdda-pll-supply = <&vreg_l3i_1p2>;
+
+ status = "okay";
+};
+
+&pcie1 {
+ wake-gpios = <&tlmm 99 GPIO_ACTIVE_HIGH>;
+ perst-gpios = <&tlmm 97 GPIO_ACTIVE_LOW>;
+
+ pinctrl-0 = <&pcie1_default_state>;
+ pinctrl-names = "default";
+
+ status = "okay";
+};
+
+&pcie1_phy {
+ vdda-phy-supply = <&vreg_l3e_0p9>;
+ vdda-pll-supply = <&vreg_l3i_1p2>;
+ vdda-qref-supply = <&vreg_l1i_0p88>;
+
+ status = "okay";
+};
+
+&pm8550_gpios {
+ sdc2_card_det_n: sdc2-card-det-state {
+ pins = "gpio12";
+ function = "normal";
+ bias-pull-up;
+ input-enable;
+ output-disable;
+ power-source = <1>; /* 1.8 V */
+ };
+};
+
&pm8550b_eusb2_repeater {
vdd18-supply = <&vreg_l15b_1p8>;
vdd3-supply = <&vreg_l5b_3p1>;
@@ -398,6 +539,43 @@ &qupv3_id_1 {
status = "okay";
};
+&remoteproc_adsp {
+ firmware-name = "qcom/sm8650/adsp.mbn",
+ "qcom/sm8650/adsp_dtb.mbn";
+
+ status = "okay";
+};
+
+&remoteproc_cdsp {
+ firmware-name = "qcom/sm8650/cdsp.mbn",
+ "qcom/sm8650/cdsp_dtb.mbn";
+
+ status = "okay";
+};
+
+&remoteproc_mpss {
+ firmware-name = "qcom/sm8650/modem.mbn",
+ "qcom/sm8650/modem_dtb.mbn";
+
+ status = "okay";
+};
+
+&sdhc_2 {
+ cd-gpios = <&pm8550_gpios 12 GPIO_ACTIVE_LOW>;
+
+ vmmc-supply = <&vreg_l9b_2p9>;
+ vqmmc-supply = <&vreg_l8b_1p8>;
+ bus-width = <4>;
+ no-sdio;
+ no-mmc;
+
+ pinctrl-0 = <&sdc2_default>, <&sdc2_card_det_n>;
+ pinctrl-1 = <&sdc2_sleep>, <&sdc2_card_det_n>;
+ pinctrl-names = "default", "sleep";
+
+ status = "okay";
+};
+
&sleep_clk {
clock-frequency = <32000>;
};
@@ -405,12 +583,58 @@ &sleep_clk {
&tlmm {
/* Reserved I/Os for NFC */
gpio-reserved-ranges = <32 8>;
+
+ disp0_reset_n_active: disp0-reset-n-active-state {
+ pins = "gpio133";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-disable;
+ };
+
+ disp0_reset_n_suspend: disp0-reset-n-suspend-state {
+ pins = "gpio133";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ mdp_vsync_active: mdp-vsync-active-state {
+ pins = "gpio86";
+ function = "mdp_vsync";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ mdp_vsync_suspend: mdp-vsync-suspend-state {
+ pins = "gpio86";
+ function = "mdp_vsync";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
};
&uart15 {
status = "okay";
};
+&ufs_mem_hc {
+ reset-gpios = <&tlmm 210 GPIO_ACTIVE_LOW>;
+
+ vcc-supply = <&vreg_l17b_2p5>;
+ vcc-max-microamp = <1300000>;
+ vccq-supply = <&vreg_l1c_1p2>;
+ vccq-max-microamp = <1200000>;
+
+ status = "okay";
+};
+
+&ufs_mem_phy {
+ vdda-phy-supply = <&vreg_l1d_0p88>;
+ vdda-pll-supply = <&vreg_l3i_1p2>;
+
+ status = "okay";
+};
+
/*
* DPAUX -> WCD9395 -> USB_SBU -> USB-C
* eUSB2 DP/DM -> PM85550HS -> eUSB2 DP/DM -> USB-C
@@ -422,7 +646,16 @@ &usb_1 {
};
&usb_1_dwc3 {
- dr_mode = "peripheral";
+ dr_mode = "otg";
+ usb-role-switch;
+};
+
+&usb_1_dwc3_hs {
+ remote-endpoint = <&pmic_glink_hs_in>;
+};
+
+&usb_1_dwc3_ss {
+ remote-endpoint = <&pmic_glink_ss_in>;
};
&usb_1_hsphy {
--
2.34.1
