[PATCH 4/4] gpio: max732x: Add DT binding documentation

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




Add a devicetree binding documentation for the max732x driver.

Signed-off-by: Semen Protsenko <semen.protsenko@xxxxxxxxxxxxxxx>
---
 .../devicetree/bindings/gpio/gpio-max732x.txt      |   59 ++++++++++++++++++++
 1 file changed, 59 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/gpio/gpio-max732x.txt

diff --git a/Documentation/devicetree/bindings/gpio/gpio-max732x.txt b/Documentation/devicetree/bindings/gpio/gpio-max732x.txt
new file mode 100644
index 0000000..5fdc843
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/gpio-max732x.txt
@@ -0,0 +1,59 @@
+* MAX732x-compatible I/O expanders
+
+Required properties:
+  - compatible: Should be one of the following:
+    - "maxim,max7319": For the Maxim MAX7319
+    - "maxim,max7320": For the Maxim MAX7320
+    - "maxim,max7321": For the Maxim MAX7321
+    - "maxim,max7322": For the Maxim MAX7322
+    - "maxim,max7323": For the Maxim MAX7323
+    - "maxim,max7324": For the Maxim MAX7324
+    - "maxim,max7325": For the Maxim MAX7325
+    - "maxim,max7326": For the Maxim MAX7326
+    - "maxim,max7327": For the Maxim MAX7327
+  - reg: I2C slave address for this device.
+  - gpio-controller: Marks the device node as a GPIO controller.
+  - #gpio-cells: Should be 2.
+    - first cell is the GPIO number
+    - second cell specifies GPIO flags, as defined in <dt-bindings/gpio/gpio.h>.
+      Only the GPIO_ACTIVE_HIGH and GPIO_ACTIVE_LOW flags are supported.
+
+Optional properties:
+
+  The I/O expander can detect input state changes, and thus optionally act as
+  an interrupt controller. When the expander interrupt line is connected all the
+  following properties must be set. For more information please see the
+  interrupt controller device tree bindings documentation available at
+  Documentation/devicetree/bindings/interrupt-controller/interrupts.txt.
+
+  - interrupt-controller: Identifies the node as an interrupt controller.
+  - #interrupt-cells: Number of cells to encode an interrupt source, shall be 2.
+    - first cell is the pin number
+    - second cell is used to specify flags
+  - interrupt-parent: phandle of the parent interrupt controller.
+  - interrupts: Interrupt specifier for the controllers interrupt.
+
+Please refer to gpio.txt in this directory for details of the common GPIO
+bindings used by client devices.
+
+Example 1. MAX7325 with interrupt support enabled (CONFIG_GPIO_MAX732X_IRQ=y):
+
+	expander: max7325@6d {
+		compatible = "maxim,max7325";
+		reg = <0x6d>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		interrupt-parent = <&gpio4>;
+		interrupts = <29 IRQ_TYPE_EDGE_FALLING>;
+	};
+
+Example 2. MAX7325 with interrupt support disabled (CONFIG_GPIO_MAX732X_IRQ=n):
+
+	expander: max7325@6d {
+		compatible = "maxim,max7325";
+		reg = <0x6d>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
-- 
1.7.9.5

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]
  Powered by Linux