On Wed, Nov 15, 2023 at 03:02:21PM +0000, Conor Dooley wrote: > On Wed, Nov 15, 2023 at 09:56:07AM -0500, Samuel Holland wrote: > > On 2023-11-15 7:27 AM, Jisheng Zhang wrote: > > > On Tue, Nov 14, 2023 at 10:12:35PM +0100, Krzysztof Kozlowski wrote: > > >> On 13/11/2023 01:55, Jisheng Zhang wrote: > > >> ... > > >> > > >>> diff --git a/include/dt-bindings/reset/sophgo,cv1800b-reset.h b/include/dt-bindings/reset/sophgo,cv1800b-reset.h > > >>> new file mode 100644 > > >>> index 000000000000..28dda71369b4 > > >>> --- /dev/null > > >>> +++ b/include/dt-bindings/reset/sophgo,cv1800b-reset.h > > >>> @@ -0,0 +1,96 @@ > > >>> +/* SPDX-License-Identifier: GPL-2.0 OR MIT */ > > >>> +/* > > >>> + * Copyright (C) 2023 Sophgo Technology Inc. All rights reserved. > > >>> + * Copyright (C) 2023 Jisheng Zhang <jszhang@xxxxxxxxxx> > > >>> + */ > > >>> + > > >>> +#ifndef _DT_BINDINGS_CV1800B_RESET_H > > >>> +#define _DT_BINDINGS_CV1800B_RESET_H > > >>> + > > >>> +/* 0-1 */ > > >>> +#define RST_DDR 2 > > >>> +#define RST_H264C 3 > > >>> +#define RST_JPEG 4 > > >>> +#define RST_H265C 5 > > >>> +#define RST_VIPSYS 6 > > >>> +#define RST_TDMA 7 > > >>> +#define RST_TPU 8 > > >>> +#define RST_TPUSYS 9 > > >>> +/* 10 */ > > >> > > >> Why do you have empty IDs? IDs start at 0 and are incremented by 1. > > > > > > there's 1:1 mapping between the ID and bit. Some bits are reserved, I.E > > > no actions at all. Is "ID start at 0 and increment by 1" documented > > > in some docs? From another side, I also notice some SoCs especially > > > those which make use of reset-simple driver don't strictly follow > > > this rule, for example, amlogic,meson-a1-reset.h and so on. What > > > happened? > > > > > > And I'd like to ask a question here before cooking 2nd version: > > > if the HW programming logic is the same as reset-simple, but some > > > or many bits are reserved, what's the can-be-accepted way to support > > > the reset controller? Use reset-simple? Obviously if we want the > > > "ID start at 0 and increment by 1" rule, then we have to write > > > a custom driver which almost use the reset-simple but with a > > > customized mapping. > > > > There are two possible situations. Either the reset specifier maps directly to > > something in the hardware, or you are inventing some brand new enumeration to > > use as a specifier. > > > > In the first situation, you do not need a header. We assume the user will look > > to the SoC documentation if they want to know what the numbers mean. (You aren't > > _creating_ an ABI, since the ABI is already defined by the hardware.) > > > > In the second situation, since we are inventing something new, the numbers > > should be contiguous. This is what Krzysztof's comment was about. > > > > For this reset device, the numbers are hardware bit offsets, so you are in the > > first situation. So I think the recommended solution here is to remove the > > header entirely and use the bit numbers directly in the SoC devicetree. > > > > It's still appropriate to use reset-simple. Adding some new mapping would make > > things more complicated for no benefit. > > Further, I think it is fine in that case to have a header, just the > header doesn't belong as a binding, and can instead go in the dts > directory. Hi Samuel, Conor, thanks a lot for the suggestion! Regards
