update: --- arch/arm64/boot/dts/qcom/ipq6018.dtsi | 15 +++++++++++++++ 1 file changed, 15 insertions(+) diff --git a/arch/arm64/boot/dts/qcom/ipq6018.dtsi b/arch/arm64/boot/dts/qcom/ipq6018.dtsi index e59b9df96..822ac51a0 100644 --- a/arch/arm64/boot/dts/qcom/ipq6018.dtsi +++ b/arch/arm64/boot/dts/qcom/ipq6018.dtsi @@ -506,6 +506,21 @@ blsp1_i2c3: i2c@78b7000 { dma-names = "tx", "rx"; status = "disabled"; }; + + blsp1_i2c6: i2c@78ba000 { + compatible = "qcom,i2c-qup-v2.2.1"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x078ba000 0x600>; + interrupts = <GIC_SPI 300 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc GCC_BLSP1_QUP6_I2C_APPS_CLK>, + <&gcc GCC_BLSP1_AHB_CLK>; + clock-names = "core", "iface"; + clock-frequency = <400000>; + dmas = <&blsp_dma 22>, <&blsp_dma 23>; + dma-names = "tx", "rx"; + status = "disabled"; + }; qpic_bam: dma-controller@7984000 { compatible = "qcom,bam-v1.7.0"; -- 2.42.0 On Wed, 15 Nov 2023 at 14:32, Bryan O'Donoghue <bryan.odonoghue@xxxxxxxxxx> wrote: > > On 15/11/2023 09:55, Legale Legale wrote: > > Add node to support this bus inside of IPQ6018. > > For example, this bus is used to work with the > > voltage regulator (mp5496) on the Yuncore AX840 wireless AP. > > > > Signed-off-by: Isaev Ruslan <legale.legale@xxxxxxxxx> > > --- > > arch/arm64/boot/dts/qcom/ipq6018.dtsi | 15 +++++++++++++++ > > 1 file changed, 15 insertions(+) > > > > diff --git a/arch/arm64/boot/dts/qcom/ipq6018.dtsi > > b/arch/arm64/boot/dts/qcom/ipq6018.dtsi > > index e59b9df96c7e..745bfc6e2907 100644 > > --- a/arch/arm64/boot/dts/qcom/ipq6018.dtsi > > +++ b/arch/arm64/boot/dts/qcom/ipq6018.dtsi > > @@ -507,6 +507,21 @@ blsp1_i2c3: i2c@78b7000 { > > status = "disabled"; > > }; > > > > + blsp1_i2c6: i2c@78ba000 { > > + compatible = "qcom,i2c-qup-v2.2.1"; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + reg = <0x078ba000 0x600>; > > reg = <0x0 0x078ba000 0x0 0x600>; > like the other regs here > > > + interrupts = <GIC_SPI 300 IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&gcc GCC_BLSP1_QUP6_I2C_APPS_CLK>, > > + <&gcc GCC_BLSP1_AHB_CLK>; > > + clock-names = "core", "iface"; > > + clock-frequency = <100000>; > > Why not <400000>; as with other nodes ? This is typo. > > > + dmas = <&blsp_dma 22>, <&blsp_dma 23>; > > + dma-names = "tx", "rx"; > > + status = "disabled"; > > + }; > > + > > qpic_bam: dma-controller@7984000 { > > compatible = "qcom,bam-v1.7.0"; > > reg = <0x0 0x07984000 0x0 0x1a000>; > > -- > > 2.42.0 > > > > What tree does this apply to ? this is master branch https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/snapshot/linux-6.7-rc1.tar.gz --branch master --depth=1 ./kernel > > git checkout -b linux-next-6.7-rc1 v6.7-rc1 > Switched to a new branch 'linux-next-6.7-rc1' > > deckard@sagittarius-a:~/Development/qualcomm/qlt-kernel$ b4 shazam > CACDmYyf4hxbuw+cpKqEDnqmHpS9yPXuE5MPD5_XZ3hjmYuViUQ@xxxxxxxxxxxxxx > > Grabbing thread from > lore.kernel.org/all/CACDmYyf4hxbuw%2BcpKqEDnqmHpS9yPXuE5MPD5_XZ3hjmYuViUQ@xxxxxxxxxxxxxx/t.mbox.gz > Checking for newer revisions > Grabbing search results from lore.kernel.org > Analyzing 1 messages in the thread > Checking attestation on all messages, may take a moment... > --- > [PATCH] arm64: dts: qcom: ipq6018: add QUP5 I2C node > --- > NOTE: install dkimpy for DKIM signature verification > --- > Total patches: 1 > --- > Applying: arm64: dts: qcom: ipq6018: add QUP5 I2C node > Patch failed at 0001 arm64: dts: qcom: ipq6018: add QUP5 I2C node > When you have resolved this problem, run "git am --continue". > If you prefer to skip this patch, run "git am --skip" instead. > To restore the original branch and stop patching, run "git am --abort". > error: git diff header lacks filename information when removing 1 > leading pathname component (line 6) > hint: Use 'git am --show-current-patch=diff' to see the failed patch > > --- > bod