RE: [PATCH v2] net: fec: fix MDIO bus assignement for dual fec SoC's

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




On 2015-01-12 03:45, fugang.duan@xxxxxxxxxxxxx wrote:
> From: Stefan Agner <stefan@xxxxxxxx> Sent: Friday, January 09, 2015 10:02 PM
>> To: davem@xxxxxxxxxxxxx
>> Cc: shawn.guo@xxxxxxxxxx; u.kleine-koenig@xxxxxxxxxxxxxx; Duan Fugang-
>> B38611; mark.rutland@xxxxxxx; robh+dt@xxxxxxxxxx; pawel.moll@xxxxxxx;
>> ijc+devicetree@xxxxxxxxxxxxxx; galak@xxxxxxxxxxxxxx; Duan Fugang-B38611;
>> LW@xxxxxxxxxxxxxxxxxxx; linux-arm-kernel@xxxxxxxxxxxxxxxxxxx; linux-
>> kernel@xxxxxxxxxxxxxxx; devicetree@xxxxxxxxxxxxxxx; stefan@xxxxxxxx;
>> Bhuvanchandra DV
>> Subject: [PATCH v2] net: fec: fix MDIO bus assignement for dual fec SoC's
>>
>> On i.MX28, the MDIO bus is shared between the two FEC instances.
>> The driver makes sure that the second FEC uses the MDIO bus of the first
>> FEC. This is done conditionally if FEC_QUIRK_ENET_MAC is set.
>> However, in newer designs, such as Vybrid or i.MX6SX, each FEC MAC has
>> its own MDIO bus. Simply removing the quirk FEC_QUIRK_ENET_MAC is not an
>> option since other logic, triggered by this quirk, is still needed.
>>
>> Furthermore, there are board designs which use the same MDIO bus for both
>> PHY's even though the second bus would be available on the SoC side. Such
>> layout are popular since it saves pins on SoC side.
>> Due to the above quirk, those boards currently do work fine. The boards
>> in the mainline tree with such a layout are:
>> - Freescale Vybrid Tower with TWR-SER2 (vf610-twr.dts)
>> - Freescale i.MX6 SoloX SDB Board (imx6sx-sdb.dts)
>>
>> This patch adds a new quirk FEC_QUIRK_SINGLE_MDIO for i.MX28, which makes
>> sure that the MDIO bus of the first FEC is used in any case.
>>
>> However, the boards above do have a SoC with a MDIO bus for each FEC
>> instance. But the PHY's are not connected in a 1:1 configuration. A
>> proper device tree description is needed to allow the driver to figure
>> out where to find its PHY. This patch fixes that shortcoming by adding a
>> MDIO bus child node to the first FEC instance, along with the two PHY's
>> on that bus, and making use of the phy-handle property to add a reference
>> to the PHY's.
>>
>> Signed-off-by: Stefan Agner <stefan@xxxxxxxx>
>> Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@xxxxxxxxxxx>
>> ---
>> Yes, this breaks existing device trees, but it does this because those
>> device trees were lacking proper description of the HW...
>> IMHO, in this case, this is acceptable. We also do this in other cases,
>> e.g. in the gic_arch_extn killing patchset:
>> http://archive.arm.linux.org.uk/lurker/message/20150107.174235.3fc3a92f.e
>> n.html
>>
>> Also, the two boards we are breaking are not very widespread:
>> The Vybrid Tower is generally not very widespread and there is only the
>> TWR-VF65GS10-PRO variant with TWR-SER2 affected. And the SoloX SDB board
>> is not even generally available yet...
>>
>> If we don't want to break the board, we could add the
>> FEC_QUIRK_SINGLE_MDIO to Vybrid or/and i.MX6SX too. But then, we need to
>> make the quirk conditional: If a MDIO node or phy- handle is specified,
>> we should rely on the device tree information.
>> However, this solution adds new code and complexity. Using the quirk for
>> those SoC's just feels wrong. So I strongly advocate for the breaking
>> variant.
>>
>> Changes since v1 (https://lkml.org/lkml/2015/1/6/284):
>> - Add MDIO/phy-handle device tree nodes for dual FEC boards
>>
>>  arch/arm/boot/dts/imx6sx-sdb.dts          | 15 +++++++++++++++
>>  arch/arm/boot/dts/vf610-twr.dts           | 15 +++++++++++++++
>>  drivers/net/ethernet/freescale/fec.h      |  2 ++
>>  drivers/net/ethernet/freescale/fec_main.c |  9 +++++----
>>  4 files changed, 37 insertions(+), 4 deletions(-)
>>
>> diff --git a/arch/arm/boot/dts/imx6sx-sdb.dts b/arch/arm/boot/dts/imx6sx-
>> sdb.dts
>> index 1e6e5cc..8c1febd 100644
>> --- a/arch/arm/boot/dts/imx6sx-sdb.dts
>> +++ b/arch/arm/boot/dts/imx6sx-sdb.dts
>> @@ -159,13 +159,28 @@
>>  	pinctrl-0 = <&pinctrl_enet1>;
>>  	phy-supply = <&reg_enet_3v3>;
>>  	phy-mode = "rgmii";
>> +	phy-handle = <&ethphy1>;
>>  	status = "okay";
>> +
>> +	mdio {
>> +		#address-cells = <1>;
>> +		#size-cells = <0>;
>> +
>> +		ethphy1: ethernet-phy@0 {
>> +			reg = <0>;
>> +		};
>> +
>> +		ethphy2: ethernet-phy@1 {
>> +			reg = <1>;
>> +		};
>> +	};
>>  };
>>
>>  &fec2 {
>>  	pinctrl-names = "default";
>>  	pinctrl-0 = <&pinctrl_enet2>;
>>  	phy-mode = "rgmii";
>> +	phy-handle = <&ethphy2>;
>>  	status = "okay";
>>  };
>>
>> diff --git a/arch/arm/boot/dts/vf610-twr.dts b/arch/arm/boot/dts/vf610-
>> twr.dts index a0f7621..f2b64b1 100644
>> --- a/arch/arm/boot/dts/vf610-twr.dts
>> +++ b/arch/arm/boot/dts/vf610-twr.dts
>> @@ -129,13 +129,28 @@
>>
>>  &fec0 {
>>  	phy-mode = "rmii";
>> +	phy-handle = <&ethphy0>;
>>  	pinctrl-names = "default";
>>  	pinctrl-0 = <&pinctrl_fec0>;
>>  	status = "okay";
>> +
>> +	mdio {
>> +		#address-cells = <1>;
>> +		#size-cells = <0>;
>> +
>> +		ethphy0: ethernet-phy@0 {
>> +			reg = <0>;
>> +		};
>> +
>> +		ethphy1: ethernet-phy@1 {
>> +			reg = <1>;
>> +		};
>> +	};
>>  };
>>
>>  &fec1 {
>>  	phy-mode = "rmii";
>> +	phy-handle = <&ethphy1>;
>>  	pinctrl-names = "default";
>>  	pinctrl-0 = <&pinctrl_fec1>;
>>  	status = "okay";
>> diff --git a/drivers/net/ethernet/freescale/fec.h
>> b/drivers/net/ethernet/freescale/fec.h
>> index 469691a..4013292 100644
>> --- a/drivers/net/ethernet/freescale/fec.h
>> +++ b/drivers/net/ethernet/freescale/fec.h
>> @@ -424,6 +424,8 @@ struct bufdesc_ex {
>>   * (40ns * 6).
>>   */
>>  #define FEC_QUIRK_BUG_CAPTURE		(1 << 10)
>> +/* Controller has only one MDIO bus */
>> +#define FEC_QUIRK_SINGLE_MDIO		(1 << 11)
>>
>>  struct fec_enet_priv_tx_q {
>>  	int index;
>> diff --git a/drivers/net/ethernet/freescale/fec_main.c
>> b/drivers/net/ethernet/freescale/fec_main.c
>> index 5ebdf8d..8dc0391 100644
>> --- a/drivers/net/ethernet/freescale/fec_main.c
>> +++ b/drivers/net/ethernet/freescale/fec_main.c
>> @@ -91,7 +91,8 @@ static struct platform_device_id fec_devtype[] = {
>>  		.driver_data = 0,
>>  	}, {
>>  		.name = "imx28-fec",
>> -		.driver_data = FEC_QUIRK_ENET_MAC | FEC_QUIRK_SWAP_FRAME,
>> +		.driver_data = FEC_QUIRK_ENET_MAC | FEC_QUIRK_SWAP_FRAME |
>> +				FEC_QUIRK_SINGLE_MDIO,
>>  	}, {
>>  		.name = "imx6q-fec",
>>  		.driver_data = FEC_QUIRK_ENET_MAC | FEC_QUIRK_HAS_GBIT | @@ -
>> 1937,7 +1938,7 @@ static int fec_enet_mii_init(struct platform_device
>> *pdev)
>>  	int err = -ENXIO, i;
>>
>>  	/*
>> -	 * The dual fec interfaces are not equivalent with enet-mac.
>> +	 * The i.MX28 dual fec interfaces are not equal.
>>  	 * Here are the differences:
>>  	 *
>>  	 *  - fec0 supports MII & RMII modes while fec1 only supports RMII
>> @@ -1952,7 +1953,7 @@ static int fec_enet_mii_init(struct platform_device
>> *pdev)
>>  	 * mdio interface in board design, and need to be configured by
>>  	 * fec0 mii_bus.
>>  	 */
>> -	if ((fep->quirks & FEC_QUIRK_ENET_MAC) && fep->dev_id > 0) {
>> +	if ((fep->quirks & FEC_QUIRK_SINGLE_MDIO) && fep->dev_id > 0) {
>>  		/* fec1 uses fec0 mii_bus */
>>  		if (mii_cnt && fec0_mii_bus) {
>>  			fep->mii_bus = fec0_mii_bus;
>> @@ -2015,7 +2016,7 @@ static int fec_enet_mii_init(struct platform_device
>> *pdev)
>>  	mii_cnt++;
>>
>>  	/* save fec0 mii_bus */
>> -	if (fep->quirks & FEC_QUIRK_ENET_MAC)
>> +	if (fep->quirks & FEC_QUIRK_SINGLE_MDIO)
>>  		fec0_mii_bus = fep->mii_bus;
>>
>>  	return 0;
>> --
>> 2.2.1
> 
> The patch limits all dts to use MDIO/phy-handle property that means
> don't support legacy mode like V1 patch comments case1 & case3.

No, not all dts need to use MDIO/phy-handle properties. The 1:1 case
(FEC connected with PHY on its own MDIO bus) works without any
properties. There is just no such board in mainline currently.

But yes the case which can be found on the two Freescale boards is not
supported without dts changes. And I think it is ok since it is a
special case which needs to have this information.

> Maybe it is the shortcut method.
> 
> In additional, it is better to split the patch to two part with dts
> and driver part.

Hm, this would mandate to have the device tree with the MDIO/phy-handle
changes merged before the net changes to maintain bisect-ability.

@Dave/Shawn, what do you prefer?

--
Stefan

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]
  Powered by Linux