The PM8937 features integrated peripherals like ADC, GPIO controller,
MPPs, PON keys and others.
Add the device tree so that any boards with this PMIC can use it.
Signed-off-by: Dang Huynh <danct12@xxxxxxxxxx>
---
arch/arm64/boot/dts/qcom/pm8937.dtsi | 202 +++++++++++++++++++++++++++++++++++
1 file changed, 202 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/pm8937.dtsi b/arch/arm64/boot/dts/qcom/pm8937.dtsi
new file mode 100644
index 000000000000..6091d6938885
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/pm8937.dtsi
@@ -0,0 +1,202 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023, Dang Huynh <danct12@xxxxxxxxxx>
+ */
+
+#include <dt-bindings/iio/qcom,spmi-vadc.h>
+#include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/pinctrl/qcom,pmic-mpp.h>
+#include <dt-bindings/spmi/spmi.h>
+
+/ {
+ thermal-zones {
+ pm8937-thermal {
+ polling-delay-passive = <0>;
+ polling-delay = <0>;
+ thermal-sensors = <&pm8937_temp>;
+
+ trips {
+ pm8937_trip0: pm8937-trip0 {
+ temperature = <105000>;
+ hysteresis = <0>;
+ type = "passive";
+ };
+ pm8937_trip1: pm8937-trip1 {
+ temperature = <125000>;
+ hysteresis = <0>;
+ type = "passive";
+ };
+ pm8937_trip2: pm8937-trip2 {
+ temperature = <145000>;
+ hysteresis = <0>;
+ type = "passive";
+ };
+ };
+ };
+ };
+};
+
+&spmi_bus {
+ pmic@0 {
+ compatible = "qcom,pm8937", "qcom,spmi-pmic";
+ reg = <0x0 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pon@800 {
+ compatible = "qcom,pm8916-pon";
+ reg = <0x800>;
+ mode-bootloader = <0x2>;
+ mode-recovery = <0x1>;
+
+ pm8937_pwrkey: pwrkey {
+ compatible = "qcom,pm8941-pwrkey";
+ interrupts = <0 0x8 0 IRQ_TYPE_EDGE_BOTH>;
+ debounce = <15625>;
+ bias-pull-up;
+ linux,code = <KEY_POWER>;
+ };
+
+ pm8937_resin: resin {
+ compatible = "qcom,pm8941-resin";
+ interrupts = <0 0x8 1 IRQ_TYPE_EDGE_BOTH>;
+ debounce = <15625>;
+ bias-pull-up;
+ linux,code = <KEY_VOLUMEDOWN>;
+ };
+ };
+
+ pm8937_gpios: gpio@c000 {
+ compatible = "qcom,pm8937-gpio", "qcom,spmi-gpio";
+ reg = <0xc000>;
+ gpio-controller;
+ gpio-ranges = <&pm8937_gpios 0 0 8>;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ pm8937_mpps: mpps@a000 {
+ compatible = "qcom,pm8937-mpp", "qcom,spmi-mpp";
+ reg = <0xa000>;
+ gpio-controller;
+ gpio-ranges = <&pm8937_mpps 0 0 4>;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ pm8937_temp: temp-alarm@2400 {
+ compatible = "qcom,spmi-temp-alarm";
+ reg = <0x2400>;
+ interrupts = <0 0x24 0 IRQ_TYPE_EDGE_RISING>;
+ io-channels = <&pm8937_vadc VADC_DIE_TEMP>;
+ io-channel-names = "thermal";
+ #thermal-sensor-cells = <0>;
+ };
+
+ pm8937_vadc: adc@3100 {
+ compatible = "qcom,spmi-vadc";
+ reg = <0x3100>;
+ interrupts = <0 0x31 0 IRQ_TYPE_EDGE_RISING>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #io-channel-cells = <1>;
+
+ channel@5 {
+ reg = <VADC_VCOIN>;
+ qcom,pre-scaling = <1 1>;
+ label = "vcoin";
+ };
+
+ channel@7 {
+ reg = <VADC_VSYS>;
+ qcom,pre-scaling = <1 1>;
+ label = "vph_pwr";
+ };
+
+ channel@8 {
+ reg = <VADC_DIE_TEMP>;
+ qcom,pre-scaling = <1 1>;
+ label = "die_temp";
+ };
+
+ channel@9 {
+ reg = <VADC_REF_625MV>;
+ qcom,pre-scaling = <1 1>;
+ label = "ref_625mv";
+ };
+
+ channel@a {
+ reg = <VADC_REF_1250MV>;
+ qcom,pre-scaling = <1 1>;
+ label = "ref_1250mv";
+ };
+
+ channel@c {
+ reg = <VADC_SPARE1>;
+ qcom,pre-scaling = <1 1>;
+ label = "ref_buf_625mv";
+ };
+
+ channel@11 {
+ reg = <VADC_P_MUX2_1_1>;
+ qcom,pre-scaling = <1 1>;
+ qcom,ratiometric;
+ qcom,hw-settle-time = <200>;
+ label = "pa_therm1";
+ };
+
+ channel@13 {
+ reg = <VADC_P_MUX4_1_1>;
+ qcom,pre-scaling = <1 1>;
+ qcom,ratiometric;
+ qcom,hw-settle-time = <200>;
+ label = "case_therm";
+ };
+
+ channel@32 {
+ reg = <VADC_LR_MUX3_XO_THERM>;
+ qcom,pre-scaling = <1 1>;
+ qcom,ratiometric;
+ qcom,hw-settle-time = <200>;
+ label = "xo_therm";
+ };
+
+ channel@36 {
+ reg = <VADC_LR_MUX7_HW_ID>;
+ qcom,pre-scaling = <1 1>;
+ qcom,ratiometric;
+ qcom,hw-settle-time = <200>;
+ label = "pa_therm0";
+ };
+
+ channel@3c {
+ reg = <VADC_LR_MUX3_BUF_XO_THERM>;
+ qcom,pre-scaling = <1 1>;
+ qcom,ratiometric;
+ qcom,hw-settle-time = <200>;
+ label = "xo_therm_buf";
+ };
+ };
+
+ rtc@6000 {
+ compatible = "qcom,pm8941-rtc";
+ reg = <0x6000>, <0x6100>;
+ reg-names = "rtc", "alarm";
+ interrupts = <0x0 0x61 0x1 IRQ_TYPE_NONE>;
+ };
+ };
+
+ pmic@1 {
+ compatible = "qcom,pm8937", "qcom,spmi-pmic";
+ reg = <0x1 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pm8937_spmi_regulators: regulators {
+ compatible = "qcom,pm8937-regulators";
+ };
+ };
+};
--
2.42.1
