Keith Zhao wrote:
> Add the dc controller and hdmi node for the Starfive JH7110 SoC.
>
> Signed-off-by: Keith Zhao <keith.zhao@xxxxxxxxxxxxxxxx>
> ---
> .../jh7110-starfive-visionfive-2.dtsi | 91 +++++++++++++++++++
> arch/riscv/boot/dts/starfive/jh7110.dtsi | 41 +++++++++
> 2 files changed, 132 insertions(+)
>
> diff --git a/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi
> index de0f40a8b..97909b6d2 100644
> --- a/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi
> +++ b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi
> @@ -31,6 +31,25 @@ memory@40000000 {
> reg = <0x0 0x40000000 0x1 0x0>;
> };
>
> + reserved-memory {
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges;
> +
> + /* vout applies for space from this CMA
> + * Without this CMA reservation,
> + * vout may not work properly.
> + */
> + linux,cma {
> + compatible = "shared-dma-pool";
> + reusable;
> + size = <0x0 0x20000000>;
> + alignment = <0x0 0x1000>;
> + alloc-ranges = <0x0 0x70000000 0x0 0x20000000>;
> + linux,cma-default;
> + };
> + };
> +
> gpio-restart {
> compatible = "gpio-restart";
> gpios = <&sysgpio 35 GPIO_ACTIVE_HIGH>;
> @@ -231,6 +250,41 @@ GPOEN_DISABLE,
> slew-rate = <0>;
> };
> };
> +
> + hdmi_pins: hdmi-0 {
> + hdmi-scl-pins {
> + pinmux = <GPIOMUX(0, GPOUT_SYS_HDMI_DDC_SCL,
> + GPOEN_SYS_HDMI_DDC_SCL,
> + GPI_SYS_HDMI_DDC_SCL)>;
> + input-enable;
> + bias-pull-up;
> + };
> +
> + hdmi-sda-pins {
> + pinmux = <GPIOMUX(1, GPOUT_SYS_HDMI_DDC_SDA,
> + GPOEN_SYS_HDMI_DDC_SDA,
> + GPI_SYS_HDMI_DDC_SDA)>;
> + input-enable;
> + bias-pull-up;
> + };
> +
> + hdmi-cec-pins {
> + pinmux = <GPIOMUX(14, GPOUT_SYS_HDMI_CEC_SDA,
> + GPOEN_SYS_HDMI_CEC_SDA,
> + GPI_SYS_HDMI_CEC_SDA)>;
> + input-enable;
> + bias-pull-up;
> + };
> +
> + hdmi-hpd-pins {
> + pinmux = <GPIOMUX(15, GPOUT_HIGH,
> + GPOEN_ENABLE,
> + GPI_SYS_HDMI_HPD)>;
> + input-enable;
> + bias-disable; /* external pull-up */
> + };
> + };
> +
Please don't break the alphabetical ordering of these nodes.
> };
>
> &uart0 {
> @@ -254,3 +308,40 @@ &U74_3 {
> &U74_4 {
> cpu-supply = <&vdd_cpu>;
> };
> +
> +&voutcrg {
> + status = "okay";
> +};
> +
> +&display {
> + status = "okay";
> +};
> +
> +&hdmi {
> + status = "okay";
> + pinctrl-names = "default";
> + pinctrl-0 = <&hdmi_pins>;
> +
> + hdmi_in: port {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + hdmi_in_dc: endpoint@0 {
> + reg = <0>;
> + remote-endpoint = <&dc_out_hdmi>;
> + };
> + };
> +};
> +
> +&dc8200 {
> + status = "okay";
> +
> + dc_out: port {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + dc_out_hdmi: endpoint@0 {
> + reg = <0>;
> + remote-endpoint = <&hdmi_in_dc>;
> + };
> +
> + };
> +};
Some goes for these node references. The order is /-node, clocks, node refences
sorted alphabetically.
> diff --git a/arch/riscv/boot/dts/starfive/jh7110.dtsi b/arch/riscv/boot/dts/starfive/jh7110.dtsi
> index 0005fa163..1670452fb 100644
> --- a/arch/riscv/boot/dts/starfive/jh7110.dtsi
> +++ b/arch/riscv/boot/dts/starfive/jh7110.dtsi
> @@ -282,6 +282,11 @@ tdm_ext: tdm-ext-clock {
> #clock-cells = <0>;
> };
>
> + display: display-subsystem {
> + compatible = "starfive,display-subsystem";
> + ports = <&dc_out>;
> + };
> +
> soc {
> compatible = "simple-bus";
> interrupt-parent = <&plic>;
> @@ -613,5 +618,41 @@ voutcrg: clock-controller@295c0000 {
> #reset-cells = <1>;
> power-domains = <&pwrc JH7110_PD_VOUT>;
> };
> +
> + dc8200: lcd-controller@29400000 {
> + compatible = "starfive,jh7110-dc8200";
> + reg = <0x0 0x29400000 0x0 0x100>,
> + <0x0 0x29400800 0x0 0x2000>;
> + interrupts = <95>;
> + clocks = <&syscrg JH7110_SYSCLK_NOC_BUS_DISP_AXI>,
> + <&voutcrg JH7110_VOUTCLK_DC8200_PIX0>,
> + <&voutcrg JH7110_VOUTCLK_DC8200_PIX1>,
> + <&voutcrg JH7110_VOUTCLK_DC8200_CORE>,
> + <&voutcrg JH7110_VOUTCLK_DC8200_AXI>,
> + <&voutcrg JH7110_VOUTCLK_DC8200_AHB>,
> + <&hdmitx0_pixelclk>,
> + <&voutcrg JH7110_VOUTCLK_DC8200_PIX>;
> + clock-names = "noc_bus", "channel0", "channel1",
> + "dc_core", "axi_core", "ahb",
> + "hdmi_tx", "dc_parent";
> + resets = <&voutcrg JH7110_VOUTRST_DC8200_AXI>,
> + <&voutcrg JH7110_VOUTRST_DC8200_AHB>,
> + <&voutcrg JH7110_VOUTRST_DC8200_CORE>;
> + reset-names = "axi","ahb", "core";
> + };
> +
> + hdmi: hdmi@29590000 {
> + compatible = "starfive,jh7110-inno-hdmi";
> + reg = <0x0 0x29590000 0x0 0x4000>;
> + interrupts = <99>;
> +
> + clocks = <&voutcrg JH7110_VOUTCLK_HDMI_TX_SYS>,
> + <&voutcrg JH7110_VOUTCLK_HDMI_TX_MCLK>,
> + <&voutcrg JH7110_VOUTCLK_HDMI_TX_BCLK>,
> + <&hdmitx0_pixelclk>;
> + clock-names = "sysclk", "mclk", "bclk", "pclk";
> + resets = <&voutcrg JH7110_VOUTRST_HDMI_TX_HDMI>;
> + #sound-dai-cells = <0>;
> + };
These nodes, however, are sorted by their address which you alse break in this
patch :(
> };
> };
> --
> 2.34.1
>
