This is an attempt to rewrite the Marvell MV88E6xxx switch bindings in YAML schema. The current text binding says: WARNING: This binding is currently unstable. Do not program it into a FLASH never to be changed again. Once this binding is stable, this warning will be removed. Well that never happened before we switched to YAML markup, we can't have it like this, what about fixing the mess? Signed-off-by: Linus Walleij <linus.walleij@xxxxxxxxxx> --- .../bindings/net/dsa/marvell,mv88e6xxx.yaml | 243 +++++++++++++++++++++ .../devicetree/bindings/net/dsa/marvell.txt | 109 --------- MAINTAINERS | 2 +- 3 files changed, 244 insertions(+), 110 deletions(-) diff --git a/Documentation/devicetree/bindings/net/dsa/marvell,mv88e6xxx.yaml b/Documentation/devicetree/bindings/net/dsa/marvell,mv88e6xxx.yaml new file mode 100644 index 000000000000..954db04147f8 --- /dev/null +++ b/Documentation/devicetree/bindings/net/dsa/marvell,mv88e6xxx.yaml @@ -0,0 +1,243 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/dsa/marvell,mv88e6xxx.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Marvell MV88E6xxx DSA switch family + +maintainers: + - Andrew Lunn <andrew@xxxxxxx> + +description: + The Marvell MV88E6xxx switch series has been produced and sold + by Marvell since at least 2010. The switch has a few compatibles which + just indicate the base address of the switch, then operating systems + can investigate switch ID registers to find out which actual version + of the switch it is dealing with. + +properties: + compatible: + oneOf: + - enum: + - marvell,mv88e6085 + - marvell,mv88e6190 + - marvell,mv88e6250 + description: | + marvell,mv88e6085: This switch uses base address 0x10. + This switch and its siblings will be autodetected from + ID registers found in the switch, so only "marvell,mv88e6085" should be + specified. This includes the following list of MV88Exxxx switches: + 6085, 6095, 6097, 6123, 6131, 6141, 6161, 6165, 6171, 6172, 6175, 6176, + 6185, 6240, 6320, 6321, 6341, 6350, 6351, 6352 + marvell,mv88e6190: This switch uses base address 0x00. + This switch and its siblings will be autodetected from + ID registers found in the switch, so only "marvell,mv88e6190" should be + specified. This includes the following list of MV88Exxxx switches: + 6190, 6190X, 6191, 6290, 6361, 6390, 6390X + marvell,mv88e6250: This switch uses base address 0x08 or 0x18. + This switch and its siblings will be autodetected from + ID registers found in the switch, so only "marvell,mv88e6250" should be + specified. This includes the following list of MV88Exxxx switches: + 6220, 6250 + + reg: + maxItems: 1 + + eeprom-length: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Set to the length of an EEPROM connected to the switch. Must be + set if the switch can not detect the presence and/or size of a connected + EEPROM, otherwise optional. + + reset-gpios: + description: + GPIO to be used to reset the whole device + maxItems: 1 + + interrupts: + description: The switch provides an external interrupt line, but it is + not always used by target systems. + maxItems: 1 + + interrupt-controller: + description: The switch has an internal interrupt controller used by + the different sub-blocks. + + '#interrupt-cells': + description: The internal interrupt controller only supports triggering + on active high level interrupts so the second cell must alway be set to + IRQ_TYPE_LEVEL_HIGH. + const: 2 + + mdio: + $ref: /schemas/net/mdio.yaml# + unevaluatedProperties: false + description: Marvell MV88E6xxx switches have an varying combination of + internal and external MDIO buses, in some cases a combined bus that + can be used both internally and externally. This node is for the + primary bus, used internally and sometimes also externally. + + mdio-external: + $ref: /schemas/net/mdio.yaml# + unevaluatedProperties: false + description: Marvell MV88E6xxx switches that have a separate external + MDIO bus use this port to access external components on the MDIO bus. + + properties: + compatible: + const: marvell,mv88e6xxx-mdio-external + + required: + - compatible + +$ref: dsa.yaml# + +patternProperties: + "^(ethernet-)?ports$": + type: object + patternProperties: + "^(ethernet-)?port@[0-9]+$": + type: object + description: Ethernet switch ports + + $ref: dsa-port.yaml# + + unevaluatedProperties: false + +oneOf: + - required: + - ports + - required: + - ethernet-ports + +required: + - compatible + - reg + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + mdio { + #address-cells = <1>; + #size-cells = <0>; + + switch0: switch@0 { + compatible = "marvell,mv88e6085"; + reg = <0>; + reset-gpios = <&gpio5 1 GPIO_ACTIVE_LOW>; + interrupt-parent = <&gpio0>; + interrupts = <27 IRQ_TYPE_LEVEL_LOW>; + interrupt-controller; + #interrupt-cells = <2>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "lan1"; + }; + port@1 { + reg = <1>; + label = "lan2"; + }; + port@2 { + reg = <2>; + label = "lan3"; + }; + port@3 { + reg = <3>; + label = "lan4"; + }; + port@4 { + reg = <4>; + label = "wan"; + }; + + port@5 { + reg = <5>; + phy-mode = "sgmii"; + ethernet = <ð2>; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + switch0phy0: switch0phy@0 { + reg = <0>; + interrupt-parent = <&switch0>; + interrupts = <0 IRQ_TYPE_LEVEL_HIGH>; + }; + }; + }; + }; + + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + mdio { + #address-cells = <1>; + #size-cells = <0>; + + switch1: switch@0 { + compatible = "marvell,mv88e6190"; + reg = <0>; + reset-gpios = <&gpio5 1 GPIO_ACTIVE_LOW>; + interrupt-parent = <&gpio0>; + interrupts = <27 IRQ_TYPE_LEVEL_LOW>; + interrupt-controller; + #interrupt-cells = <2>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "lan1"; + }; + port@1 { + reg = <1>; + label = "lan2"; + }; + port@2 { + reg = <2>; + label = "lan3"; + }; + port@3 { + reg = <3>; + label = "lan4"; + }; + }; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + switch1phy0: switch1phy@0 { + reg = <0>; + interrupt-parent = <&switch1>; + interrupts = <0 IRQ_TYPE_LEVEL_HIGH>; + }; + }; + + mdio-external { + compatible = "marvell,mv88e6xxx-mdio-external"; + #address-cells = <1>; + #size-cells = <0>; + switch1phy9: switch1phy@9 { + reg = <9>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/dsa/marvell.txt b/Documentation/devicetree/bindings/net/dsa/marvell.txt deleted file mode 100644 index 6ec0c181b6db..000000000000 --- a/Documentation/devicetree/bindings/net/dsa/marvell.txt +++ /dev/null @@ -1,109 +0,0 @@ -Marvell DSA Switch Device Tree Bindings ---------------------------------------- - -WARNING: This binding is currently unstable. Do not program it into a -FLASH never to be changed again. Once this binding is stable, this -warning will be removed. - -If you need a stable binding, use the old dsa.txt binding. - -Marvell Switches are MDIO devices. The following properties should be -placed as a child node of an mdio device. - -The properties described here are those specific to Marvell devices. -Additional required and optional properties can be found in dsa.txt. - -The compatibility string is used only to find an identification register, -which is at a different MDIO base address in different switch families. -- "marvell,mv88e6085" : Switch has base address 0x10. Use with models: - 6085, 6095, 6097, 6123, 6131, 6141, 6161, 6165, - 6171, 6172, 6175, 6176, 6185, 6240, 6320, 6321, - 6341, 6350, 6351, 6352 -- "marvell,mv88e6190" : Switch has base address 0x00. Use with models: - 6190, 6190X, 6191, 6290, 6361, 6390, 6390X -- "marvell,mv88e6250" : Switch has base address 0x08 or 0x18. Use with model: - 6220, 6250 - -Required properties: -- compatible : Should be one of "marvell,mv88e6085", - "marvell,mv88e6190" or "marvell,mv88e6250" as - indicated above -- reg : Address on the MII bus for the switch. - -Optional properties: - -- reset-gpios : Should be a gpio specifier for a reset line -- interrupts : Interrupt from the switch -- interrupt-controller : Indicates the switch is itself an interrupt - controller. This is used for the PHY interrupts. -#interrupt-cells = <2> : Controller uses two cells, number and flag -- eeprom-length : Set to the length of an EEPROM connected to the - switch. Must be set if the switch can not detect - the presence and/or size of a connected EEPROM, - otherwise optional. -- mdio : Container of PHY and devices on the switches MDIO - bus. -- mdio? : Container of PHYs and devices on the external MDIO - bus. The node must contains a compatible string of - "marvell,mv88e6xxx-mdio-external" - -Example: - - mdio { - #address-cells = <1>; - #size-cells = <0>; - interrupt-parent = <&gpio0>; - interrupts = <27 IRQ_TYPE_LEVEL_LOW>; - interrupt-controller; - #interrupt-cells = <2>; - - switch0: switch@0 { - compatible = "marvell,mv88e6085"; - reg = <0>; - reset-gpios = <&gpio5 1 GPIO_ACTIVE_LOW>; - - mdio { - #address-cells = <1>; - #size-cells = <0>; - switch1phy0: switch1phy0@0 { - reg = <0>; - interrupt-parent = <&switch0>; - interrupts = <0 IRQ_TYPE_LEVEL_HIGH>; - }; - }; - }; - }; - - mdio { - #address-cells = <1>; - #size-cells = <0>; - interrupt-parent = <&gpio0>; - interrupts = <27 IRQ_TYPE_LEVEL_LOW>; - interrupt-controller; - #interrupt-cells = <2>; - - switch0: switch@0 { - compatible = "marvell,mv88e6190"; - reg = <0>; - reset-gpios = <&gpio5 1 GPIO_ACTIVE_LOW>; - - mdio { - #address-cells = <1>; - #size-cells = <0>; - switch1phy0: switch1phy0@0 { - reg = <0>; - interrupt-parent = <&switch0>; - interrupts = <0 IRQ_TYPE_LEVEL_HIGH>; - }; - }; - - mdio1 { - compatible = "marvell,mv88e6xxx-mdio-external"; - #address-cells = <1>; - #size-cells = <0>; - switch1phy9: switch1phy0@9 { - reg = <9>; - }; - }; - }; - }; diff --git a/MAINTAINERS b/MAINTAINERS index 90f13281d297..1b4475254d27 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -12625,7 +12625,7 @@ MARVELL 88E6XXX ETHERNET SWITCH FABRIC DRIVER M: Andrew Lunn <andrew@xxxxxxx> L: netdev@xxxxxxxxxxxxxxx S: Maintained -F: Documentation/devicetree/bindings/net/dsa/marvell.txt +F: Documentation/devicetree/bindings/net/dsa/marvell,mv88e6xxx.yaml F: Documentation/networking/devlink/mv88e6xxx.rst F: drivers/net/dsa/mv88e6xxx/ F: include/linux/dsa/mv88e6xxx.h -- 2.34.1
