Re: [PATCH v3 2/2] iio: adc: ads7038: Add driver support for 12bit ADC

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Sun, 15 Oct 2023 20:32:21 +0200
werneazc@xxxxxxxxx wrote:

> From: Andre Werner <andre.werner@xxxxxxxxxxxxxxxxxxxxx>
> 
> The driver is designed to support both, ADS7038 and ADS7138, but the
> implementation of the device access is limited to ADS7038 (SPI). The
> ADS7138 is accessed via I2C.
> 
> The driver has a regmap and a core file that abstracts device access.
> Currently, the driver does support manual measure mode only.
> 
> One can trigger an offset calibration using sysfs option for the
> provided IIO device. The programmable average filter can be configured
> via devicetree option as well as appending status information.
> The CRC option is not implemented but configurable.
> 
> The GPIO functionality is completely missing.
> 
> Signed-off-by: Andre Werner <andre.werner@xxxxxxxxxxxxxxxxxxxxx>
> ---
> v3:
> - Delete ads7038_info struct for regmap access
> - Add new regulator for DVDD voltage
> - Shift regulators form SPI device to IIO device
> - Add attributes for last channel read, CRC, status and average samples (RO)
> - Add option to trigger offset calibration (WO)
> - Implement Average Sampling for manual measure mode. That effects the
>   measure cycle and for that the time to get the return value.
> - Additional code improvements that where recommendet by the reviewer
>   such es renaming of defines or variables as well as deleting of
>   explicit casts or const pointers.
> - Uodate Kconfig so that the ADS7038 SPI device selects the common
>   module functions that shall be provided to add the ADS7138 (I2C)
>   version easily.
> 
> Sadly, the device has no interrupt to show the status of a running
> measure cycle. But a full measure cycle with 128 samples takes
> approximately 130us. The driver uses a simple delay between
> transmissions of an SPI message. An alternative
> needs to poll a single bit in the device's status register. In my
> opinion that is a bad alternative if the device is not the only on at
> the SPI bus.
> 
> The functionality is tested with Kernel 5.10 and ported to Linux master.
Various comments inline.

Given you are doing a forwards port I guess the guard() stuff can wait for
a cleanup patch after this merges to make your life a little easier.

Jonathan

> ---
>  MAINTAINERS                         |  10 +
>  drivers/iio/adc/Kconfig             |  15 +
>  drivers/iio/adc/Makefile            |   3 +
>  drivers/iio/adc/ti-ads7038-core.c   | 415 ++++++++++++++++++++++++++
>  drivers/iio/adc/ti-ads7038-regmap.c |  89 ++++++
>  drivers/iio/adc/ti-ads7038-spi.c    | 269 +++++++++++++++++
>  drivers/iio/adc/ti-ads7038.h        | 433 ++++++++++++++++++++++++++++
>  7 files changed, 1234 insertions(+)
>  create mode 100644 drivers/iio/adc/ti-ads7038-core.c
>  create mode 100644 drivers/iio/adc/ti-ads7038-regmap.c
>  create mode 100644 drivers/iio/adc/ti-ads7038-spi.c
>  create mode 100644 drivers/iio/adc/ti-ads7038.h
> 
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 7a7bd8bd80e9..dd0cae0405d0 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -21247,6 +21247,16 @@ T:	git https://github.com/jcmvbkbc/linux-xtensa.git
>  F:	arch/xtensa/
>  F:	drivers/irqchip/irq-xtensa-*
>  
> +TEXAS INSTRUMENT'S ADS7038 ADC DRIVER
> +M:	Andre Werner <andre.werner@xxxxxxxxxxxxxxxxxxxxx>
> +L:	linux-iio@xxxxxxxxxxxxxxx
> +S:	Maintained
> +F:	Documentation/devicetree/bindings/iio/adc/ti,ads7038.yaml
> +F:	drivers/iio/adc/ti-ads7038.h
> +F:	drivers/iio/adc/ti-ads7038-core.c
> +F:	drivers/iio/adc/ti-ads7038-regmap.c
> +F:	drivers/iio/adc/ti-ads7038-spi.c
> +
>  TEXAS INSTRUMENTS ASoC DRIVERS
>  M:	Peter Ujfalusi <peter.ujfalusi@xxxxxxxxx>
>  L:	alsa-devel@xxxxxxxxxxxxxxxx (moderated for non-subscribers)
> diff --git a/drivers/iio/adc/Kconfig b/drivers/iio/adc/Kconfig
> index 517b3db114b8..d5725a87a54c 100644
> --- a/drivers/iio/adc/Kconfig
> +++ b/drivers/iio/adc/Kconfig
> @@ -1239,6 +1239,21 @@ config TI_ADS1015
>  	  This driver can also be built as a module. If so, the module will be
>  	  called ti-ads1015.
>  
> +config TI_ADS7038_COMMON
> +	tristate
> +	depends on TI_ADS7038_SPI
> +
> +config TI_ADS7038_SPI
> +	tristate "Texas Instruments ADS7038 ADC driver"
> +	depends on SPI_MASTER
> +	select REGMAP
> +	select TI_ADS7038_COMMON
> +	help
> +	  Say yes here to build support for TI ADS7038 12BIT ADC (SPI connected).
> +
> +	  To compile this driver as a module, choose M here: the core module
> +	  will be called ti-ads7038 and you will also get ti-ads7038-spi for SPI support.
> +
>  config TI_ADS7924
>  	tristate "Texas Instruments ADS7924 ADC"
>  	depends on I2C
> diff --git a/drivers/iio/adc/Makefile b/drivers/iio/adc/Makefile
> index 2facf979327d..3583ceb4c8c8 100644
> --- a/drivers/iio/adc/Makefile
> +++ b/drivers/iio/adc/Makefile
> @@ -111,6 +111,9 @@ obj-$(CONFIG_TI_ADC128S052) += ti-adc128s052.o
>  obj-$(CONFIG_TI_ADC161S626) += ti-adc161s626.o
>  obj-$(CONFIG_TI_ADS1015) += ti-ads1015.o
>  obj-$(CONFIG_TI_ADS1100) += ti-ads1100.o
> +obj-$(CONFIG_TI_ADS7038_COMMON) += ti-ads7038.o
> +ti-ads7038-objs := ti-ads7038-core.o ti-ads7038-regmap.o
> +obj-$(CONFIG_TI_ADS7038_SPI) += ti-ads7038-spi.o
>  obj-$(CONFIG_TI_ADS7924) += ti-ads7924.o
>  obj-$(CONFIG_TI_ADS7950) += ti-ads7950.o
>  obj-$(CONFIG_TI_ADS8344) += ti-ads8344.o
> diff --git a/drivers/iio/adc/ti-ads7038-core.c b/drivers/iio/adc/ti-ads7038-core.c
> new file mode 100644
> index 000000000000..04095e836076
> --- /dev/null
> +++ b/drivers/iio/adc/ti-ads7038-core.c
> @@ -0,0 +1,415 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later
> +/* This driver supports TI 12Bit ADC devices
> + *
> + *	 - ADS7038 with SPI interface
> + *
> + * Copyright (C) 2023 SYS TEC electronic AG
> + * Author: Andre Werner <andre.werner@xxxxxxxxxxxxxxxxxxxxx>
> + */
> +#include <linux/device.h>
> +#include <linux/errno.h>
> +#include <linux/fwnode.h>
> +#include <linux/iio/iio.h>
> +#include <linux/iio/types.h>
> +#include <linux/module.h>
> +#include <linux/mutex.h>
> +#include <linux/property.h>
> +#include <linux/regmap.h>
> +#include <linux/regulator/consumer.h>
> +#include <linux/sysfs.h>
> +
> +#include "ti-ads7038.h"
> +
> +#define ADS7038_AVERAGE_OUTPUT_BITS	16
> +
> +#define ADS7038_V_CHAN(_chan, _addr)				\
> +	{							\
> +	.type = IIO_VOLTAGE,					\
> +	.indexed = 1,						\
> +	.address = _addr,					\
> +	.channel = _chan,					\
> +	.info_mask_separate = BIT(IIO_CHAN_INFO_RAW),		\
> +	.info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE),	\
> +	.scan_index = _addr,					\
> +	.scan_type = {						\
> +		.sign = 's',					\
> +		.realbits = 12,					\
> +		.storagebits = 16,				\
> +		.shift = 4,					\
> +		.endianness = IIO_CPU,				\
You don't yet provide the buffered chardev IIO interface, so this is irrelevant for now.
Add it when you need it only.

> +	},							\
> +	.datasheet_name = "AIN"#_chan,				\
> +	}
> +
> +static const struct iio_chan_spec ads7038_channels[] = {
> +	ADS7038_V_CHAN(0, AIN0), ADS7038_V_CHAN(1, AIN1),
> +	ADS7038_V_CHAN(2, AIN2), ADS7038_V_CHAN(3, AIN3),
> +	ADS7038_V_CHAN(4, AIN4), ADS7038_V_CHAN(5, AIN5),
> +	ADS7038_V_CHAN(6, AIN6), ADS7038_V_CHAN(7, AIN7),
> +};
> +
> +static ssize_t ads7038_crc_show(struct device *dev, struct device_attribute *attr,
> +				char *buf)
> +{
> +	const struct iio_dev *indio_dev = dev_get_drvdata(dev);
> +	struct ads7038_data *data = iio_priv(indio_dev);
> +
> +	return sysfs_emit(buf, "%s\n", data->crc_enabled ? "enabled (not implement)" : "disabled");

Always on unless you provide a strong reason why not.
People don't spend money on a more expensive chip with CRC if they don't want it ;)

> +}
> +
> +static ssize_t ads7038_status_show(struct device *dev, struct device_attribute *attr,
> +				   char *buf)
> +{
> +	const struct iio_dev *indio_dev = dev_get_drvdata(dev);
> +	struct ads7038_data *data = iio_priv(indio_dev);

Debug information only - if you really want it either break it up into useful things to report
via events etc, or throw it in debugfs.

> +
> +	return sysfs_emit(buf, "0x%01X\n", data->status_appended ? data->current_status : 0xFF);
> +}
> +
> +static ssize_t ads7038_chanid_show(struct device *dev, struct device_attribute *attr,
> +				   char *buf)
> +{
> +	const struct iio_dev *indio_dev = dev_get_drvdata(dev);
> +	struct ads7038_data *data = iio_priv(indio_dev);
> +

Userspace controlled what channel was read, so it already knows this.

> +	return sysfs_emit(buf, "%d\n", data->latest_chanid);

> +}
> +
> +static ssize_t ads7038_cycletime_show(struct device *dev, struct device_attribute *attr,
> +				      char *buf)
> +{
> +	const struct iio_dev *indio_dev = dev_get_drvdata(dev);
> +	struct ads7038_data *data = iio_priv(indio_dev);
> +
> +	return sysfs_emit(buf, "%d us\n", data->measure_cycle_time_us);
Convert this to standard sampling_frequency ABI.  (1/cycle time)
> +}
> +
> +static ssize_t ads7038_calibrate_store(struct device *dev, struct device_attribute *attr,
> +				       const char *buf, size_t count)
> +{
> +	const struct iio_dev *indio_dev = dev_get_drvdata(dev);
> +	struct ads7038_data *data = iio_priv(indio_dev);
> +	int ret;
> +	unsigned int regval, loop_cnt = 10;
> +
> +	mutex_lock(&data->lock);
> +	ret = regmap_read(data->regmap, ADS7038_GENERAL_CFG_REG, &regval);
> +	if (ret < 0)
> +		goto error;
> +
> +	regval |= ADS7038_GENERAL_CFG_CAL;
> +
> +	ret = regmap_write(data->regmap, ADS7038_GENERAL_CFG_REG, regval);
> +	if (ret < 0)
> +		goto error;
> +
> +	do {
> +		ret = regmap_read(data->regmap, ADS7038_GENERAL_CFG_REG, &regval);
> +		if (ret < 0)
> +			goto error;
> +		--loop_cnt;
> +	} while ((regval & ADS7038_GENERAL_CFG_CAL) && (loop_cnt < 0));
> +
> +	if (loop_cnt)
> +		ret = count;
> +	else
> +		ret = -EIO;
> +error:
> +	mutex_unlock(&data->lock);
> +	return ret;
> +}
> +
> +static DEVICE_ATTR_RO(ads7038_crc);
> +static DEVICE_ATTR_RO(ads7038_status);
> +static DEVICE_ATTR_RO(ads7038_chanid);
> +static DEVICE_ATTR_RO(ads7038_cycletime);
> +static DEVICE_ATTR_WO(ads7038_calibrate);
> +
> +static struct attribute *ads7038_dev_attrs[] = {
Documentation needed for all of these.

Note that we are resistant to adding custom ABI to IIO without very strong
reasons.  Calibration is probably valid, but the rest don't look it to me.
They should either map to standard ABI Documentation/ABI/testing/sysfs-bus-iio
or not be exposed to userspace at all.

Custom ABI is basically unused ABI as generic software doesn't know about it.
So one of the most important things to do in the IIO subsystem is prevent
it being added unless absolutely necessary.

Even calibration can sometimes be simply moved to device probe time depending on how
it is done (I haven't checked here).

> +	&dev_attr_ads7038_crc.attr,
> +	&dev_attr_ads7038_status.attr,
> +	&dev_attr_ads7038_chanid.attr,
> +	&dev_attr_ads7038_cycletime.attr,
> +	&dev_attr_ads7038_calibrate.attr,
> +	NULL,
> +};
> +ATTRIBUTE_GROUPS(ads7038_dev);
> +
> +static int ads7038_regulator_config(struct iio_dev *const indio_dev,
> +				    struct ads7038_data *const data)
> +{
> +	struct regulator *reg;
> +	int ret;
> +
> +	mutex_lock(&data->lock);
> +	ret = regulator_register_supply_alias(&indio_dev->dev, "avdd", data->dev, "avdd");

Why?  Look it up on data->dev instead.  Adding this indirection is pointless given it's
only used here!

> +	if (ret < 0)
> +		goto error;
> +
> +	reg = devm_regulator_get(&indio_dev->dev, "avdd");
> +	if (IS_ERR(reg)) {
> +		dev_dbg(&indio_dev->dev, "Failed to get regulator \"AVDD\"\n");
> +		ret = PTR_ERR(reg);
> +		goto error;
> +	}
> +
> +	ret = regulator_enable(reg);
> +	if (ret < 0) {
> +		dev_dbg(&indio_dev->dev, "Failed to enable regulator \"AVDD\"\n");
> +		goto error;
> +	}
> +
> +	data->avdd_reg = reg;
> +
> +	ret = regulator_register_supply_alias(&indio_dev->dev, "dvdd", data->dev, "dvdd");
> +	if (ret < 0)
> +		goto error;
> +
> +	reg = devm_regulator_get(&indio_dev->dev, "dvdd");

As mentioned below, you never do anything with this one, so
	ret = devm_regulator_get_enabled().
and no need to keep a pointer to it around.

> +	if (IS_ERR(reg)) {
> +		dev_dbg(&indio_dev->dev, "Failed to get regulator \"DVDD\"\n");
> +		ret = PTR_ERR(reg);
> +		goto error;
> +	}
> +
> +	ret = regulator_enable(reg);
> +	if (ret < 0) {
> +		dev_dbg(&indio_dev->dev, "Failed to enable regulator \"DVDD\"\n");
> +		goto error;
> +	}
> +
> +	data->dvdd_reg = reg;
> +
> +error:
> +	mutex_unlock(&data->lock);
> +	return 0;
> +}

> +
> +static int ads7038_config_average(struct ads7038_data *const data, const u32 ov_ratio)
> +{
> +	int ret;
> +	struct regmap *map = data->regmap;
> +	unsigned int regval;
> +
> +	if (ov_ratio > ADS7038_OSR_CFG_OSR_128)
> +		return -EINVAL;
> +
> +	mutex_lock(&data->lock);

	guard(mutex)(&data->lock);

then you can do direct returns on error, simplifying this a little.
Same in other similar cases so I'll stop pointing this out.

> +	ret = regmap_read(map, ADS7038_OSR_CFG_REG, &regval);
> +	if (ret < 0)
> +		goto error;
> +
> +	regval = (ret & ~ADS7038_OSR_CFG_OSR) | ov_ratio;
> +
> +	ret = regmap_write(map, ADS7038_OSR_CFG_REG, regval);
> +	if (ret < 0)
> +		goto error;
> +
> +	data->measure_cycle_time_us = (1 << ov_ratio) * ADS7038_CYCLE_TIME_US;
> +	if (ov_ratio == ADS7038_OSR_CFG_OSR_NO)
> +		data->avaraging_enabled = false;
> +	else
> +		data->avaraging_enabled = true;
> +
> +error:
> +	mutex_unlock(&data->lock);
> +	return ret;
> +}
> +
> +static int ads7038_set_mode_manual(struct device const *dev, struct regmap *const map)
> +{
> +	int ret;
> +	const unsigned int regs[] = { ADS7038_OPMODE_CFG_REG,
> +		ADS7038_SEQUENCE_CFG_REG
> +	};
> +	unsigned int reg_values[2] = { 0 };
> +	unsigned int idx;
> +
> +	/* Registers need to be read first to adapt configuration bits. */
> +	for (idx = 0; idx < ARRAY_SIZE(regs); ++idx) {
> +		ret = regmap_read(map, regs[idx], &reg_values[idx]);
> +		if (ret < 0) {
> +			dev_dbg(dev,
> +				"Cannot read value from register %02X.\n",
> +				regs[idx]);
> +			break;
> +		}
> +	}
> +
> +	if (ret < 0)
> +		goto out;
		return ret;
> +
> +	reg_values[0] &= ~ADS7038_OPMODE_CFG_CONV_MODE;
> +	reg_values[0] |= ADS7038_OPMODE_CFG_CONV_MODE_MANUAL;
> +	reg_values[0] &= ~ADS7038_SEQUENCE_CFG_SEQ_MODE;
> +	reg_values[0] |= ADS7038_SEQUENCE_CFG_SEQ_MODE_MANUAL;
> +
> +	for (idx = 0; idx < ARRAY_SIZE(regs); ++idx) {
> +		ret = regmap_write(map, regs[idx], reg_values[idx]);
> +		if (ret < 0) {
> +			dev_dbg(dev,
> +				"Cannot write value to register %02X.\n",
> +				regs[idx]);
> +			break;
> +		}
> +	}
> +out:
Not needed.

> +	return ret;
> +}
> +
> +static int ads7038_read_raw(struct iio_dev *indio_dev,
> +			    struct iio_chan_spec const *chan,
> +		     int *val, int *val2,
> +		     long mask)
> +{
> +	unsigned int ret;
> +	struct ads7038_ch_meas_result tmp_val;

Not zero initialized so I think you can get garbage in status_valid.

> +	struct ads7038_data *data = iio_priv(indio_dev);
> +
> +	switch (mask) {
> +	case IIO_CHAN_INFO_RAW:
> +		ret = data->read_channel_raw(indio_dev, chan->channel, &tmp_val);
> +
> +		if (ret < 0) {
> +			dev_err(&indio_dev->dev, "Read channel returned with error %d", ret);
> +			return ret;
> +		}
> +
> +		*val = tmp_val.raw;
> +
Given lock is not held over the read and this feels like there is probably a race here.

> +		mutex_lock(&data->lock);
> +		if (data->status_appended) {
> +			if (tmp_val.status_valid)
> +				data->current_status = tmp_val.status;
> +			else
> +				dev_warn(&indio_dev->dev, "No valid status reported by device.\n");
> +		}
> +		data->latest_chanid = chan->channel;
> +		mutex_unlock(&data->lock);
> +
> +		return IIO_VAL_INT;
> +	case IIO_CHAN_INFO_SCALE:
> +		mutex_lock(&data->lock);
> +		ret = regulator_get_voltage(data->avdd_reg);
> +		mutex_unlock(&data->lock);
> +		if (ret < 0)
> +			return ret;
> +
> +		*val = ret / 1000;	/* uV -> mV */
> +		if (data->avaraging_enabled)

spell check.  averaging


> +			*val2 = 1 << ADS7038_AVERAGE_OUTPUT_BITS;
> +		else
> +			*val2 = 1 << chan->scan_type.realbits;
> +
> +		return IIO_VAL_FRACTIONAL;
> +	default:
> +		return -EINVAL;
> +	}
> +}

> +
> +int ads7038_common_probe(struct device *parent, read_channel_raw_cb read_ch_raw_cb,
> +			 struct regmap *const regmap,
> +			 const char *name, int irq)
> +{
> +	struct ads7038_data *data;
> +	struct iio_dev *indio_dev;
> +	u32 prop_value;
> +	int ret;
> +
> +	indio_dev = devm_iio_device_alloc(parent, sizeof(struct ads7038_data));

sizeof(*data) preferred as then I don't have to go check types.

> +	if (!indio_dev)
> +		return -ENOMEM;
> +
> +	indio_dev->name = name;
> +	indio_dev->channels = ads7038_channels;
> +	indio_dev->num_channels = ARRAY_SIZE(ads7038_channels);
> +	indio_dev->info = &ads7038_iio_info;
> +	indio_dev->modes = INDIO_DIRECT_MODE;
> +
> +	data = iio_priv(indio_dev);
> +	mutex_init(&data->lock);
> +	data->dev = parent;
> +	data->read_channel_raw = read_ch_raw_cb;
> +	data->regmap = regmap;
> +
> +	ret = ads7038_regulator_config(indio_dev, data);
> +	if (ret < 0)
> +		return ret;
> +
> +	ret = ads7038_enable_status(data, device_property_present(parent, "status-enabled"));
Discussion going on in the binding doc revies.
> +	if (ret < 0) {
> +		dev_dbg(&indio_dev->dev,
> +			"Error while configuring appending of chip status (ret = %d)\n",
> +			ret);
> +		return ret;
> +	}
> +
> +	ret = device_property_read_u32(parent, "average-samples", &prop_value);

This sounds like over sampling.  That should be controlled by userspace via
the stand IIO oversampling interfaces.

> +	if (ret == 0) {
> +		ret = ads7038_config_average(data, prop_value);
> +		if (ret < 0) {
> +			dev_dbg(&indio_dev->dev,
> +				"Error while configuring appending of chip status (ret = %d)\n",
> +				ret);
> +			return ret;
> +		}
> +	}
> +
> +	data->crc_enabled = device_property_present(parent, "crc-enabled");
Discussion ongoing in binding doc rview.

> +
> +	/* Configure read manual mode for single read of channel value */
> +	ret = ads7038_set_mode_manual(&indio_dev->dev, data->regmap);
> +	if (ret < 0)
> +		return ret;
> +
> +	data->func_mode = MAN;
> +
> +	/* Link general device driver with IIO device driver data */
> +	dev_set_drvdata(parent, indio_dev);
The IIO core does that for you. So should not be needed

> +
> +	devm_iio_device_register(data->dev, indio_dev);
> +
> +	ret = devm_device_add_groups(&indio_dev->dev, ads7038_dev_groups);

Why?  Generally we just use the parent dev for all devm actions as that results in
the correct cleanup.  Is there something different going on here.


> +	if (ret < 0)
> +		return ret;
> +
> +	return 0;
> +}
> +EXPORT_SYMBOL_NS_GPL(ads7038_common_probe, IIO_ADS7038);
> +
> +MODULE_AUTHOR("Andre Werner <andre.werner@xxxxxxxxxxxxxxxxxxxxx>");
> +MODULE_DESCRIPTION("ADS7038 and ADS7138 core driver");
> +MODULE_LICENSE("GPL");
> diff --git a/drivers/iio/adc/ti-ads7038-regmap.c b/drivers/iio/adc/ti-ads7038-regmap.c
> new file mode 100644
> index 000000000000..fcc2f0b9d3a9
> --- /dev/null
> +++ b/drivers/iio/adc/ti-ads7038-regmap.c

Squash this with the core file.  No benefit in breaking it out to it's own file.

> @@ -0,0 +1,89 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later
> +/* This driver supports TI 12Bit ADC devices
> + *
> + * Register mapping for both ADS7x38 devices (I2C and SPI interface)
> + *
> + * Copyright (C) 2023 SYS TEC electronic AG
> + * Author: Andre Werner <andre.werner@xxxxxxxxxxxxxxxxxxxxx>
> + */
> +#include <linux/module.h>
> +#include <linux/regmap.h>
> +
> +#include "ti-ads7038.h"
> +
> +static const struct regmap_range ads7038_noaccess_ranges[] = {
> +	regmap_reg_range(0x06, 0x06), regmap_reg_range(0x08, 0x08),
> +	regmap_reg_range(0x0A, 0x0A), regmap_reg_range(0x0C, 0x0C),
> +	regmap_reg_range(0x0E, 0x0F), regmap_reg_range(0x15, 0x15),
> +	regmap_reg_range(0x19, 0x19), regmap_reg_range(0x1B, 0x1B),
> +	regmap_reg_range(0x1D, 0x1D), regmap_reg_range(0x1F, 0x1F),
> +	regmap_reg_range(0x40, 0x5F), regmap_reg_range(0x70, 0x7F),
> +	regmap_reg_range(0xB0, 0xC2), regmap_reg_range(0xC4, 0xC4),
> +	regmap_reg_range(0xC6, 0xC6), regmap_reg_range(0xC8, 0xC8),
> +	regmap_reg_range(0xCA, 0xCA), regmap_reg_range(0xCC, 0xCC),
> +	regmap_reg_range(0xCE, 0xCE), regmap_reg_range(0xD0, 0xD0),
> +	regmap_reg_range(0xD2, 0xE8), regmap_reg_range(0xEA, 0xEA),
> +};
> +
> +/* It is okay to include noaccess registers in range, because they have been proven at first. */
> +static const struct regmap_range ads7038_readable_ranges[] = {
> +	regmap_reg_range(0x00, ADS7038_REG_ADDRESS_MAX),
> +};
> +
> +static const struct regmap_access_table ads7038_readable_table = {
> +	.yes_ranges = ads7038_readable_ranges,
> +	.n_yes_ranges = 0,	/* regmap.c: In case zero "yes ranges" are supplied, any reg is OK */
> +	.no_ranges = ads7038_noaccess_ranges,
> +	.n_no_ranges = ARRAY_SIZE(ads7038_noaccess_ranges),
> +};
> +
> +static const struct regmap_range ads7038_volatile_ranges[] = {
> +	regmap_reg_range(ADS7038_SYSTEM_STATUS_REG, ADS7038_GENERAL_CFG_REG),
> +	regmap_reg_range(ADS7038_GPI_VALUE_REG, ADS7038_GPI_VALUE_REG),
> +	regmap_reg_range(ADS7038_EVENT_FLAG_REG, ADS7038_EVENT_FLAG_REG),
> +	regmap_reg_range(ADS7038_MAX_CH0_LSB_REG, ADS7038_MAX_CH7_MSB_REG),
> +	regmap_reg_range(ADS7038_MIN_CH0_LSB_REG, ADS7038_MIN_CH7_MSB_REG),
> +	regmap_reg_range(ADS7038_RECENT_CH0_LSB_REG,
> +			 ADS7038_RECENT_CH7_MSB_REG),
> +};
> +
> +static const struct regmap_access_table ads7038_volatile_table = {
> +	.yes_ranges = ads7038_volatile_ranges,
> +	.n_yes_ranges = ARRAY_SIZE(ads7038_volatile_ranges),
> +	.no_ranges = ads7038_noaccess_ranges,
> +	.n_no_ranges = ARRAY_SIZE(ads7038_noaccess_ranges),
> +};
> +
> +/* It is okay to include noaccess registers in range, because they have been proven at first. */
> +static const struct regmap_range ads7038_writable_range[] = {
> +	regmap_reg_range(ADS7038_SYSTEM_STATUS_REG, ADS7038_GPO_VALUE_REG),
> +	regmap_reg_range(ADS7038_SEQUENCE_CFG_REG, ADS7038_ALERT_PIN_CFG_REG),
> +	regmap_reg_range(ADS7038_EVENT_HIGH_FLAG_REG, ADS7038_LOW_TH_CH7_REG),
> +	regmap_reg_range(ADS7038_GPO0_TRIG_EVENT_SEL_REG,
> +			 ADS7038_GPO_VALUE_TRIG_REG),
> +};
> +
> +static const struct regmap_access_table ads7038_writable_table = {
> +	.yes_ranges = ads7038_writable_range,
> +	.n_yes_ranges = ARRAY_SIZE(ads7038_writable_range),
> +	.no_ranges = ads7038_noaccess_ranges,
> +	.n_no_ranges = ARRAY_SIZE(ads7038_noaccess_ranges),
> +};
> +
> +const struct regmap_config ads7038_regmap_config = {
> +	.name = "ads7038",
> +	.reg_bits = ADS7038_REGISTER_NUM_BITS,

Better to put numbers here so we can immediately see what this is.
Generally using a define for a 'number' that has direct meaning just makes code
less readable.  Keep them for encoded values etc.

> +	.val_bits = ADS7038_REGISTER_NUM_BITS,
> +
> +	.wr_table = &ads7038_writable_table,
> +	.rd_table = &ads7038_readable_table,
> +	.volatile_table = &ads7038_volatile_table,
> +
> +	.max_register = ADS7038_REG_ADDRESS_MAX,
> +	.cache_type = REGCACHE_RBTREE,
> +};
> +EXPORT_SYMBOL_NS_GPL(ads7038_regmap_config, IIO_ADS7038);
> +
> +MODULE_AUTHOR("Andre Werner <andre.werner@xxxxxxxxxxxxxxxxxxxxx>");
> +MODULE_DESCRIPTION("ADS7x38 register mapping");
> +MODULE_LICENSE("GPL");
> diff --git a/drivers/iio/adc/ti-ads7038-spi.c b/drivers/iio/adc/ti-ads7038-spi.c
> new file mode 100644
> index 000000000000..163a76001138
> --- /dev/null
> +++ b/drivers/iio/adc/ti-ads7038-spi.c
> @@ -0,0 +1,269 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later
> +/*
> + * This driver supports TI 12Bit ADC devices
> + *
> + *	 - ADS7038 with SPI interface
> + *
> + * Copyright (C) 2023 SYS TEC electronic AG
> + * Author: Andre Werner <andre.werner@xxxxxxxxxxxxxxxxxxxxx>
> + */
> +#include <linux/bitfield.h>
> +#include <linux/delay.h>
> +#include <linux/device.h>
> +#include <linux/err.h>
> +#include <linux/iio/iio.h>
> +#include <linux/module.h>
> +#include <linux/regmap.h>
> +#include <linux/spi/spi.h>
> +#include <linux/types.h>
> +
> +#include "ti-ads7038.h"
> +
> +#define ADS7038_OPCODE_NOOP		0x00
> +#define ADS7038_OPCODE_REGREAD		0x10
> +#define ADS7038_OPCODE_REGWRITE		0x08
> +#define ADS7038_OPCODE_SETBIT		0x18
> +#define ADS7038_OPCODE_CLEATBIT		0x20
> +
> +/*
> + * The bitwidth for ADC channel results differ
> + * by setting average and status
> + * in the dedicated configuration registers.
> + */
> +#define ADS7038_NO_AVG_NO_STAT		12	/* bits */
> +#define ADS7038_NO_AVG_STAT		16	/* bits */
> +#define ADS7038_AVG_NO_STAT		16	/* bits */
> +#define ADS7038_AVG_STAT		20	/* bits */
> +
> +#define ADS7038_SPI_FRAME_SIZE_REG		3	/* bytes */
> +#define ADS7038_SPI_FRAME_SIZE_CHAN_MAX		2	/* elements */
> +
> +static int ads7038_regmap_spi_read(void *context, unsigned int reg,
> +				   unsigned int *val)
> +{
> +	struct device *dev = context;
> +	struct spi_device *spi = to_spi_device(dev);
> +	int ret;
> +	const u8 tx_buf[ADS7038_SPI_FRAME_SIZE_REG] = {
> +		[0] = ADS7038_OPCODE_REGREAD,
> +		[1] = (u8)(reg & GENMASK(7, 0)),
> +		[2] = 0,	/* dummy data */
> +	};
> +	u8 rx_buf[ADS7038_SPI_FRAME_SIZE_REG] = { 0 };
> +
> +	/* Data contains 8bit address and 8bit register data */
> +	struct spi_transfer xfer[] = {
> +		{
> +			.tx_buf = tx_buf,
> +			.rx_buf = NULL,
Don't set null
> +			.len = ADS7038_SPI_FRAME_SIZE_REG,
use sizeof(tx_buf),

> +			.bits_per_word = ADS7038_REGISTER_NUM_BITS,
Use a value.
> +			.cs_change = 1,
> +		},
> +		{
> +			.tx_buf = NULL,
> +			.rx_buf = rx_buf,
> +			.len = ADS7038_SPI_FRAME_SIZE_REG,

Use a value or size of where you are storing the data.  Also be careful
about DMA saftety as mentioned below.

> +			.bits_per_word = ADS7038_REGISTER_NUM_BITS,
Use a value
> +		},
> +	};
> +
> +	if (!val)
> +		return -EINVAL;
> +
> +	ret = spi_sync_transfer(spi, xfer, ARRAY_SIZE(xfer));
> +
> +	if (ret < 0)
> +		return ret;
> +
> +	*val = rx_buf[0];
> +
> +	return 0;
> +}
> +
> +static int ads7038_regmap_spi_write(void *context, unsigned int reg,
> +				    unsigned int val)
> +{
> +	unsigned int ret;
> +	struct device *dev = (struct device *)context;
> +	struct spi_device *spi = to_spi_device(dev);
> +	const u8 buf[ADS7038_SPI_FRAME_SIZE_REG] = {
> +		[0] = ADS7038_OPCODE_REGWRITE,
> +		[1] = (u8)(reg & GENMASK(7, 0)),
> +		[2] = (u8)(val & GENMASK(7, 0)),
> +	};
> +
> +	struct spi_transfer xfer[] = {
> +		{
> +			.tx_buf = buf,
> +			.rx_buf = NULL,
> +			.len = ARRAY_SIZE(buf),
> +		},
> +	};
> +
> +	ret = spi_sync_transfer(spi, xfer, ARRAY_SIZE(xfer));
> +
> +	if (ret < 0)
> +		return ret;
> +
> +	return 0;
> +}
> +
> +static int ads7038_read_channel(struct iio_dev *const indio_dev,
> +				const enum MANUAL_CHID chan,
> +				struct ads7038_ch_meas_result *const res)
> +{
> +	int ret;
> +	struct ads7038_data *data = iio_priv(indio_dev);
> +	struct spi_device *spi_dev = to_spi_device(data->dev);
> +	__be16 rx_buf[ADS7038_SPI_FRAME_SIZE_CHAN_MAX] = { 0 };

Buffers passed to spi subsystem for spi_sync need to be DMA safe.
See how we have put them on in the iio_priv() structure + applied specific
alignment in many other drivers to meet this requirement.

> +
> +	const u8 tx_buf[] = {
> +		[0] = ADS7038_OPCODE_REGWRITE,
> +		[1] = ADS7038_CHANNEL_SEL_REG,
> +		[2] = chan
> +	};
> +
> +	/*
> +	 * If the channel changes it needs two additional cycles before the result
> +	 * is ready to tranmit.
This is odd enough that a reference to the relevant diagram or specification section
would be good.
May even be worth some asci art here to explain this a little more clearly.

> +	 */
> +	struct spi_transfer xfer[] = {
> +		{
> +			.tx_buf = tx_buf,
> +			.rx_buf = NULL,
> +			.len = sizeof(tx_buf),
> +			.tx_nbits = SPI_NBITS_SINGLE,
> +			.cs_change = 1,
> +			.cs_change_delay = {
> +				.value = data->measure_cycle_time_us,
> +				.unit = SPI_DELAY_UNIT_USECS
I think it's fairly unusual for an spi controller to support single bit transfers llike
this.  Can you get away with a 8 bit one?  I assume what really matters is the
clock signal going up and down.
> +			},
> +		},
> +		{
> +			.dummy_data = 1,
> +			.len = sizeof(tx_buf),
> +			.tx_nbits = SPI_NBITS_SINGLE,
> +			.cs_change = 1,
> +			.cs_change_delay = {
> +				.value = data->measure_cycle_time_us,
> +				.unit = SPI_DELAY_UNIT_USECS
> +			},
> +		},
> +		{
> +			.tx_buf = NULL,

No need to set things to NULL.  C deals with that for you and it's an obvious default that
you've used a few times anyway.

> +			.rx_buf = rx_buf,
> +			.len = sizeof(rx_buf),
> +			.tx_nbits = SPI_NBITS_SINGLE,
> +			.cs_change = 1,
> +			.cs_change_delay = {
> +				.value = data->measure_cycle_time_us,
> +				.unit = SPI_DELAY_UNIT_USECS
> +			},
> +		},
> +		{
> +			.dummy_data = 1,
> +			.len = sizeof(rx_buf),
> +			.tx_nbits = SPI_NBITS_SINGLE,
> +		},
> +	};
> +
> +	if (chan > AIN_MAX)
> +		return -EINVAL;
> +
> +	mutex_lock(&data->lock);
guard(mutex)(&data->lock);
probably helpful here as then you can return directly in error paths and let the autocleanup deal
with it for you.  It's a new feature in the kernel so not that many users around yet.

> +
> +	/* If the channel does not switch we do not need to send that transfers again */
> +	if (data->latest_chanid != chan)
> +		ret = spi_sync_transfer(spi_dev, xfer, ARRAY_SIZE(xfer));
> +	else
> +		ret = spi_sync_transfer(spi_dev, &xfer[1], (ARRAY_SIZE(xfer) - 1));
> +
> +	if (ret < 0)
> +		goto out;
> +
> +	if (data->avaraging_enabled) {
> +		res->raw = be16_to_cpu(rx_buf[0]);
> +		res->raw_is_an_average = true;
> +		if (data->status_appended) {
> +			res->status = FIELD_GET(GENMASK(15, 12), (be16_to_cpup(&rx_buf[1])));
> +			res->status_valid = true;
> +		}
> +	} else {
> +		res->raw = be16_to_cpu(rx_buf[0]);
> +		res->raw >>= 4;
> +		if (data->status_appended) {
> +			res->status = FIELD_GET(GENMASK(3, 0), (be16_to_cpup(&rx_buf[0])));
> +			res->status_valid = true;
> +		}
> +	}
> +
> +out:
> +	mutex_unlock(&data->lock);
> +	return ret;
> +}
> +
> +static struct regmap_bus ads7038_regmap_bus = {
> +	.reg_write = ads7038_regmap_spi_write,
> +	.reg_read = ads7038_regmap_spi_read,
> +	.reg_format_endian_default = REGMAP_ENDIAN_LITTLE,
> +	.val_format_endian_default = REGMAP_ENDIAN_LITTLE,

Combining regmap with a function that bypasses regmap feels like a bad idea.
I'd just not use regmap at all for this device as it seems to need too complex
handling. Sometimes it's just not a good fit.

> +};
> +
> +static int ads7038_spi_probe(struct spi_device *spi)
> +{
> +	const struct spi_device_id *id = spi_get_device_id(spi);
> +	struct regmap *regmap;
> +	int ret;
> +
> +	ret = spi_setup(spi);

The firmware handling should have already done this for you.
Why do you need to call it here?

> +	if (ret < 0) {
> +		dev_dbg(&spi->dev, "spi_setup failed!\n");
dev_err_probe()


> +		goto error_spi;
> +	}
> +
> +	regmap = devm_regmap_init(&spi->dev, &ads7038_regmap_bus, &spi->dev,
> +				  &ads7038_regmap_config);
> +	if (IS_ERR(regmap)) {
> +		dev_dbg(&spi->dev, "Failed to allocate register map\n");
Useful error message if fails, so dev_err_probe()

> +		ret = PTR_ERR(regmap);
> +		goto error_spi;
> +	}
> +
> +	return ads7038_common_probe(&spi->dev, ads7038_read_channel, regmap,
> +				    id->name, spi->irq);
> +
> +error_spi:
> +	dev_err(&spi->dev, "Probe failed\n");
That's easily checked anyway so don't print this message.
> +	return ret;
> +}
> +

> diff --git a/drivers/iio/adc/ti-ads7038.h b/drivers/iio/adc/ti-ads7038.h
> new file mode 100644
> index 000000000000..898b3cfd4694
> --- /dev/null
> +++ b/drivers/iio/adc/ti-ads7038.h
> @@ -0,0 +1,433 @@
> +/* SPDX-License-Identifier: GPL-2.0-or-later */
> +/*
> + * This driver supports TI 12Bit ADC devices
> + *
> + *	 - ADS7038 with SPI interface
> + *	 - ADS7138 with I2C interface (future)
> + *
> + * Copyright (C) 2023 SYS TEC electronic AG
> + * Author: Andre Werner <andre.werner@xxxxxxxxxxxxxxxxxxxxx>
> + */
> +#include <linux/bitops.h>
> +#include <linux/mutex.h>
> +#include <linux/types.h>
> +
> +#ifndef IIO_TI_ADS7038_H_
> +#define IIO_TI_ADS7038_H_
> +
> +#define ADS7038_REGISTER_NUM_BITS	8
> +#define ADS7038_CYCLE_TIME_US		1
> +
> +/* Opcodes for commands */
> +#define ADS7038_OP_NOOP		0x00
> +#define ADS7038_OP_REG_READ	0x10
> +#define ADS7038_OP_REG_WRITE	0x08
> +#define ADS7038_OP_SET_BIT	0x18
> +#define ADS7038_OP_CLEAR_BIT	0x20
> +
> +#define ADS7038_SYSTEM_STATUS_REG		0x00
> +#define ADS7038_SYSTEM_STATUS_BOR		BIT(0)
> +#define ADS7038_SYSTEM_STATUS_CRC_ERROR_IN	BIT(1)
> +#define ADS7038_SYSTEM_STATUS_CRC_ERROR_FUSE	BIT(2)
> +#define ADS7038_SYSTEM_STATUS_OSR_DONE		BIT(3)
> +#define ADS7038_SYSTEM_STATUS_OSR_SEQ_STATUS	BIT(6)
> +
> +#define ADS7038_GENERAL_CFG_REG		0x01
> +#define ADS7038_GENERAL_CFG_RST		BIT(0)
> +#define ADS7038_GENERAL_CFG_CAL		BIT(1)
> +#define ADS7038_GENERAL_CFG_CH_RST	BIT(2)
> +#define ADS7038_GENERAL_CFG_DWC_EN	BIT(4)
> +#define ADS7038_GENERAL_CFG_STATS_EN	BIT(5)
> +#define ADS7038_GENERAL_CFG_CRC_EN	BIT(6)
> +
> +#define ADS7038_DATA_CFG_REG			0x02
> +#define ADS7038_DATA_CFG_CPOL_CPHA		GENMASK(1, 0)
> +#define ADS7038_DATA_CFG_CPOL_CPHA_SPI00	0x00	/* solely ADS7038 */
> +#define ADS7038_DATA_CFG_CPOL_CPHA_SPI01	0x01	/* solely ADS7038 */
> +#define ADS7038_DATA_CFG_CPOL_CPHA_SPI10	0x02	/* solely ADS7038 */
> +#define ADS7038_DATA_CFG_CPOL_CPHA_SPI11	0x03	/* solely ADS7038 */
> +#define ADS7038_DATA_CFG_APPEND_STATUS		GENMASK(5, 4)
> +#define ADS7038_DATA_CFG_APPEND_STATUS_NO	0x00
> +#define ADS7038_DATA_CFG_APPEND_STATUS_CHID	BIT(4)
> +#define ADS7038_DATA_CFG_APPEND_STATUS_STATUS	BIT(5)
> +#define ADS7038_DATA_CFG_FIX_PAT		BIT(7)
> +
> +#define ADS7038_OSR_CFG_REG	0x03
> +#define ADS7038_OSR_CFG_OSR	GENMASK(2, 0)
> +#define ADS7038_OSR_CFG_OSR_NO	0x00

As this is 1 effectively can do this with maths.
#define ADS7038_OSR_CFG_OSR(x) __ffs()

> +#define ADS7038_OSR_CFG_OSR_2	0x01
> +#define ADS7038_OSR_CFG_OSR_4	0x02
> +#define ADS7038_OSR_CFG_OSR_8	0x03
> +#define ADS7038_OSR_CFG_OSR_16	0x04
> +#define ADS7038_OSR_CFG_OSR_32	0x05
> +#define ADS7038_OSR_CFG_OSR_64	0x06
> +#define ADS7038_OSR_CFG_OSR_128	0x07
> +
> +#define ADS7038_OPMODE_CFG_REG			0x04
> +#define ADS7038_OPMODE_CFG_CLK_DIV		GENMASK(3, 0)
> +#define ADS7038_OPMODE_CFG_CLK_DIV_FTIME_1US0	0x00
> +#define ADS7038_OPMODE_CFG_CLK_DIV_FTIME_1US5	0x01
> +#define ADS7038_OPMODE_CFG_CLK_DIV_FTIME_2US0	0x02
> +#define ADS7038_OPMODE_CFG_CLK_DIV_FTIME_3US0	0x03
> +#define ADS7038_OPMODE_CFG_CLK_DIV_FTIME_4US0	0x04
> +#define ADS7038_OPMODE_CFG_CLK_DIV_FTIME_6US0	0x05
> +#define ADS7038_OPMODE_CFG_CLK_DIV_FTIME_8US0	0x06
> +#define ADS7038_OPMODE_CFG_CLK_DIV_FTIME_12US0	0x07
> +#define ADS7038_OPMODE_CFG_CLK_DIV_FTIME_16US0	0x08
> +#define ADS7038_OPMODE_CFG_CLK_DIV_FTIME_24US0	0x09
> +#define ADS7038_OPMODE_CFG_CLK_DIV_FTIME_32US0	0x0A
> +#define ADS7038_OPMODE_CFG_CLK_DIV_FTIME_48US0	0x0B
> +#define ADS7038_OPMODE_CFG_CLK_DIV_FTIME_64US0	0x0C
> +#define ADS7038_OPMODE_CFG_CLK_DIV_FTIME_96US0	0x0D
> +#define ADS7038_OPMODE_CFG_CLK_DIV_FTIME_128US0	0x0E
> +#define ADS7038_OPMODE_CFG_CLK_DIV_FTIME_192US0	0x0F
> +#define ADS7038_OPMODE_CFG_OSC_SEL		BIT(4)
> +#define ADS7038_OPMODE_CFG_OSC_SEL_HIGHSPEED	0x00
> +#define ADS7038_OPMODE_CFG_OSC_SEL_LOWSPEED	0x01
> +#define ADS7038_OPMODE_CFG_CONV_MODE		GENMASK(6, 5)
> +#define ADS7038_OPMODE_CFG_CONV_MODE_MANUAL	0x00
> +#define ADS7038_OPMODE_CFG_CONV_MODE_AUTONOMOUS	BIT(5)
> +#define ADS7038_OPMODE_CFG_CONV_ON_ERR		BIT(7)
> +#define ADS7038_OPMODE_CFG_CONV_ON_ERR_CONTINUE	0x00
> +#define ADS7038_OPMODE_CFG_CONV_ON_ERR_PAUSE	BIT(7)
> +
> +#define ADS7038_PIN_CFG_REG		0x05
> +#define ADS7038_PIN_CFG_ALL_AIN		0x00
> +#define ADS7038_PIN_CFG_ALL_GPIO	GENMASK(7, 0)
> +
> +#define ADS7038_GPIO_CFG_REG		0x07
> +#define ADS7038_GPIO_CFG_ALL_IN		0x00
> +#define ADS7038_GPIO_CFG_ALL_OUT	GENMASK(7, 0)
> +
> +#define ADS7038_GPO_DRIVE_CFG_REG		0x09
> +#define ADS7038_GPO_DRIVE_CFG_ALL_OPEN_DRAIN	0x00
> +#define ADS7038_GPO_DRIVE_CFG_ALL_PP		GENMASK(7, 0)
> +
> +#define ADS7038_GPO_VALUE_REG		0x0B
> +#define ADS7038_GPO_VALUE_ALL_LOW	0x00
> +#define ADS7038_GPO_VALUE_ALL_HIGH	GENMASK(7, 0)
> +
> +#define ADS7038_GPI_VALUE_REG		0x0D
> +
> +#define ADS7038_SEQUENCE_CFG_REG			0x10
> +#define ADS7038_SEQUENCE_CFG_SEQ_MODE			GENMASK(1, 0)
> +#define ADS7038_SEQUENCE_CFG_SEQ_MODE_MANUAL		0x00
> +#define ADS7038_SEQUENCE_CFG_SEQ_MODE_AUTO_SEQ		0x01
> +#define ADS7038_SEQUENCE_CFG_SEQ_MODE_ON_THE_FLY	0x02	/* solely ADS7038 */
> +#define ADS7038_SEQUENCE_CFG_SEQ_START BIT(4)
> +
> +#define ADS7038_CHANNEL_SEL_REG			0x11
> +#define ADS7038_CHANNEL_SEL_MCHILDID		GENMASK(3, 0)
> +#define ADS7038_CHANNEL_SEL_MCHILDID_AIN0	0x00
> +#define ADS7038_CHANNEL_SEL_MCHILDID_AIN1	0x01
> +#define ADS7038_CHANNEL_SEL_MCHILDID_AIN2	0x02
> +#define ADS7038_CHANNEL_SEL_MCHILDID_AIN3	0x03
> +#define ADS7038_CHANNEL_SEL_MCHILDID_AIN4	0x04
> +#define ADS7038_CHANNEL_SEL_MCHILDID_AIN5	0x05
> +#define ADS7038_CHANNEL_SEL_MCHILDID_AIN6	0x06
> +#define ADS7038_CHANNEL_SEL_MCHILDID_AIN7	0x07
> +
> +#define ADS7038_AUTO_SEQ_CH_SEL_REG	0x12
> +#define ADS7038_AUTO_SEQ_CH_SEL_ALL	GENMASK(7, 0)
> +
> +#define ADS7038_ALERT_CH_SEL_REG	0x14
> +#define ADS7038_ALERT_CH_SEL_ALL	GENMASK(7, 0)
> +
> +#define ADS7038_ALERT_MAP_REG		0x16
> +#define ADS7038_ALERT_MAP_ALERT_CRCIN	BIT(0)
> +
> +#define ADS7038_ALERT_PIN_CFG_REG			0x17
> +#define ADS7038_ALERT_PIN_CFG_ALERT_LOGIC		GENMASK(1, 0)
> +#define ADS7038_ALERT_PIN_CFG_ALERT_LOGIC_ACTIVE_LOW	0x00
> +#define ADS7038_ALERT_PIN_CFG_ALERT_LOGIC_ACTIVE_HIGH	BIT(0)
> +#define ADS7038_ALERT_PIN_CFG_ALERT_LOGIC_PULSED_LOW	BIT(1)
> +#define ADS7038_ALERT_PIN_CFG_ALERT_LOGIC_PULSED_HIGH	GENMASK(1, 0)
> +#define ADS7138_ALERT_PIN_CFG_ALERT_DRIVE		BIT(2)	/* solely ADS7138 */
> +#define ADS7038_ALERT_PIN_CFG_ALERT_PIN			0xF0	/* solely ADS7038 */
> +
> +#define ADS7038_EVENT_FLAG_REG	0x18
> +
> +#define ADS7038_EVENT_HIGH_FLAG_REG	0x1A
> +
> +#define ADS7038_EVENT_LOW_FLAG_REG	0x1C
> +
> +#define ADS7038_EVENT_RGN_REG	0x1E
> +
> +#define ADS7038_HYSTERESIS_CH0_REG			0x20
> +#define ADS7038_HYSTERESIS_CH0_HYSTERESIS_CH0		GENMASK(3, 0)

Where there are a lot of similar registers, you an normally get away with defining
the registers individually etc, but the fields as something like.
ADS7038_HYSTERESIS_CH_HIGH_THRESHOLD_LSB

> +#define ADS7038_HYSTERESIS_CH0_HIGH_THRESHOLD_CH0_LSB	GENMASK(7, 4)

The second CH0 is probably redundant.

> +
> +#define ADS7038_HIGH_TH_CH0_REG		0x21
> +
> +#define ADS7038_EVENT_CNT_CH0_REG			0x22
> +#define ADS7038_EVENT_CNT_CH0_EVENT_CNT_CH0		GENMASK(3, 0)
> +#define ADS7038_EVENT_CNT_CH0_LOW_THRESHOLD_CH0_LSB	GENMASK(7, 4)
> +
> +#define ADS7038_LOW_TH_CH0_REG	0x23
> +
> +#define ADS7038_HYSTERESIS_CH1_REG			0x24
> +#define ADS7038_HYSTERESIS_CH1_HYSTERESIS_CH0		GENMASK(3, 0)
> +#define ADS7038_HYSTERESIS_CH1_HIGH_THRESHOLD_CH0_LSB	GENMASK(7, 4)
> +
> +#define ADS7038_HIGH_TH_CH1_REG	0x25
> +
> +#define ADS7038_EVENT_CNT_CH1_REG			0x26
> +#define ADS7038_EVENT_CNT_CH1_EVENT_CNT_CH0		GENMASK(3, 0)
> +#define ADS7038_EVENT_CNT_CH1_LOW_THRESHOLD_CH0_LSB	GENMASK(7, 4)
> +
> +#define ADS7038_LOW_TH_CH1_REG	0x27
> +
> +#define ADS7038_HYSTERESIS_CH2_REG			0x28
> +#define ADS7038_HYSTERESIS_CH2_HYSTERESIS_CH0		GENMASK(3, 0)
> +#define ADS7038_HYSTERESIS_CH2_HIGH_THRESHOLD_CH0_LSB	GENMASK(7, 4)
> +
> +#define ADS7038_HIGH_TH_CH2_REG				0x29
> +
> +#define ADS7038_EVENT_CNT_CH2_REG			0x2A
> +#define ADS7038_EVENT_CNT_CH2_EVENT_CNT_CH0		GENMASK(3, 0)
> +#define ADS7038_EVENT_CNT_CH2_LOW_THRESHOLD_CH0_LSB	GENMASK(7, 4)
> +
> +#define ADS7038_LOW_TH_CH2_REG	0x2B
> +
> +#define ADS7038_HYSTERESIS_CH3_REG			0x2C
> +#define ADS7038_HYSTERESIS_CH3_HYSTERESIS_CH0		GENMASK(3, 0)
> +#define ADS7038_HYSTERESIS_CH3_HIGH_THRESHOLD_CH0_LSB	GENMASK(7, 4)
> +
> +#define ADS7038_HIGH_TH_CH3_REG				0x2D
> +
> +#define ADS7038_EVENT_CNT_CH3_REG			0x2E
> +#define ADS7038_EVENT_CNT_CH3_EVENT_CNT_CH0		GENMASK(3, 0)
> +#define ADS7038_EVENT_CNT_CH3_LOW_THRESHOLD_CH0_LSB	GENMASK(7, 4)
> +
> +#define ADS7038_LOW_TH_CH3_REG 0x2F
> +
> +#define ADS7038_HYSTERESIS_CH4_REG			0x30
> +#define ADS7038_HYSTERESIS_CH4_HYSTERESIS_CH0		GENMASK(3, 0)
> +#define ADS7038_HYSTERESIS_CH4_HIGH_THRESHOLD_CH0_LSB	GENMASK(7, 4)
> +
> +#define ADS7038_HIGH_TH_CH4_REG				0x31
> +
> +#define ADS7038_EVENT_CNT_CH4_REG			0x32
> +#define ADS7038_EVENT_CNT_CH4_EVENT_CNT_CH0		GENMASK(3, 0)
> +#define ADS7038_EVENT_CNT_CH4_LOW_THRESHOLD_CH0_LSB	GENMASK(7, 4)
> +
> +#define ADS7038_LOW_TH_CH4_REG				0x33
> +
> +#define ADS7038_HYSTERESIS_CH5_REG			0x34
> +#define ADS7038_HYSTERESIS_CH5_HYSTERESIS_CH0		GENMASK(3, 0)
> +#define ADS7038_HYSTERESIS_CH5_HIGH_THRESHOLD_CH0_LSB	GENMASK(7, 4)
> +
> +#define ADS7038_HIGH_TH_CH5_REG				0x35
> +
> +#define ADS7038_EVENT_CNT_CH5_REG			0x36
> +#define ADS7038_EVENT_CNT_CH5_EVENT_CNT_CH0		GENMASK(3, 0)
> +#define ADS7038_EVENT_CNT_CH5_LOW_THRESHOLD_CH0_LSB	GENMASK(7, 4)
> +
> +#define ADS7038_LOW_TH_CH5_REG				0x37
> +
> +#define ADS7038_HYSTERESIS_CH6_REG			0x38
> +#define ADS7038_HYSTERESIS_CH6_HYSTERESIS_CH0		GENMASK(3, 0)
> +#define ADS7038_HYSTERESIS_CH6_HIGH_THRESHOLD_CH0_LSB	GENMASK(7, 4)
> +
> +#define ADS7038_HIGH_TH_CH6_REG 0x39
> +
> +#define ADS7038_EVENT_CNT_CH6_REG			0x3A
> +#define ADS7038_EVENT_CNT_CH6_EVENT_CNT_CH0		GENMASK(3, 0)
> +#define ADS7038_EVENT_CNT_CH6_LOW_THRESHOLD_CH0_LSB	GENMASK(7, 4)
> +
> +#define ADS7038_LOW_TH_CH6_REG				0x3B
> +
> +#define ADS7038_HYSTERESIS_CH7_REG			0x3C
> +#define ADS7038_HYSTERESIS_CH7_HYSTERESIS_CH0		GENMASK(3, 0)
> +#define ADS7038_HYSTERESIS_CH7_HIGH_THRESHOLD_CH0_LSB	GENMASK(7, 4)
> +
> +#define ADS7038_HIGH_TH_CH7_REG				0x3D
> +
> +#define ADS7038_EVENT_CNT_CH7_REG			0x3E
> +#define ADS7038_EVENT_CNT_CH7_EVENT_CNT_CH0		GENMASK(3, 0)
> +#define ADS7038_EVENT_CNT_CH7_LOW_THRESHOLD_CH0_LSB	GENMASK(7, 4)
> +
> +#define ADS7038_LOW_TH_CH7_REG		0x3F

No point in blank lines between these.  Just reduces what is on the screen
when someone is reading the code!

So please only put them when they are separating blocks of defines like the
ones above.

> +
> +#define ADS7038_MAX_CH0_LSB_REG		0x60
> +
> +#define ADS7038_MAX_CH0_MSB_REG		0x61
> +

...

> +
> +/* Channel IDs to use for manual mode */
> +enum MANUAL_CHID {
> +	AIN0 = ADS7038_CHANNEL_SEL_MCHILDID_AIN0,
> +	AIN1 = ADS7038_CHANNEL_SEL_MCHILDID_AIN1,
> +	AIN2 = ADS7038_CHANNEL_SEL_MCHILDID_AIN2,
> +	AIN3 = ADS7038_CHANNEL_SEL_MCHILDID_AIN3,
> +	AIN4 = ADS7038_CHANNEL_SEL_MCHILDID_AIN4,
> +	AIN5 = ADS7038_CHANNEL_SEL_MCHILDID_AIN5,
> +	AIN6 = ADS7038_CHANNEL_SEL_MCHILDID_AIN6,
> +	AIN7 = ADS7038_CHANNEL_SEL_MCHILDID_AIN7,
> +	AIN_MAX
> +};
> +
> +/* Functional Measure Modes */
> +enum FUNC_MODE {
> +	UNKNOWN = 0,
> +	MAN,
> +	ON_THE_FLY,
> +	AUTO_SEQ,
> +	AUTO,
> +};
> +
> +struct ads7038_ch_meas_result {
> +	unsigned int raw;
> +	unsigned int status;
> +	bool raw_is_an_average;
> +	bool status_valid;
> +};
> +
> +struct device;
> +struct iio_dev;
> +struct regmap;
> +struct regulator;
> +
> +/* Perform a single read of a channel */
> +typedef int (*read_channel_raw_cb)(struct iio_dev *const indio_dev,
> +			    const enum MANUAL_CHID chan,
> +			    struct ads7038_ch_meas_result *const res);
> +
> +struct ads7038_data {
> +	struct device *dev;
> +	struct regmap *regmap;
> +	struct mutex lock;		/* Mutex for single communication resource */

The bus drivers will have locks as will regmap.  So either you don't need a lock, or
it's protecting some other data?

> +	struct regulator *avdd_reg;	/* Regulator that controls ADC reference voltage */
> +	struct regulator *dvdd_reg;	/* Regulator digital I/O voltage */
Never accessed after being set, so no point in keeping it around.
> +
> +	enum FUNC_MODE func_mode;	/* actual measure mode */
> +	bool crc_enabled;
> +	bool avaraging_enabled;
> +	bool status_appended;
> +	u8 current_status;		/* Chip status if enabled */
> +	u8 latest_chanid;		/* Latest channel id requested */
> +	u16 measure_cycle_time_us;
> +
> +	read_channel_raw_cb read_channel_raw;
> +};
> +
> +extern const struct regmap_config ads7038_regmap_config;
> +
> +int ads7038_common_probe(struct device *parent, read_channel_raw_cb read_ch_raw_cb,

Long line. Aim to wrap below 80 chars unless it is hurting readability.

> +			 struct regmap *const regmap,
> +			 const char *name, const int irq);
> +
> +#endif





[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux