Dne petek, 13. oktober 2023 ob 21:18:00 CEST je Jernej Škrabec napisal(a): > Dne petek, 06. oktober 2023 ob 11:01:30 CEST je Julian Ribbeck napisal(a): > > Iteaduino Plus A20 is very similar to Iteaduino Plus A10. In fact it > > shares the same breakout board and the Itead Core A20 on top of it, is > > only adapted to support the dual-core A20. > > > > This commits enables the following hardware: > > > > * HDMI Video output > > * USB > > * SATA (untested due to lack of hardware I could attach) > > * Ethernet > > * MMC storage > > * UART > > * USB OTG (untested, because I don't own an USB OTG cable/device) > > > > Signed-off-by: Julian Ribbeck <julian.ribbeck@xxxxxx> > > --- > > arch/arm/boot/dts/allwinner/Makefile | 1 + > > .../sun7i-a20-itead-iteaduino-plus.dts | 104 ++++++++++++++++++ > > 2 files changed, 105 insertions(+) > > create mode 100644 arch/arm/boot/dts/allwinner/sun7i-a20-itead-iteaduino-plus.dts > > > > diff --git a/arch/arm/boot/dts/allwinner/Makefile b/arch/arm/boot/dts/allwinner/Makefile > > index eebb5a0c873a..39af5ad94590 100644 > > --- a/arch/arm/boot/dts/allwinner/Makefile > > +++ b/arch/arm/boot/dts/allwinner/Makefile > > @@ -124,6 +124,7 @@ dtb-$(CONFIG_MACH_SUN7I) += \ > > sun7i-a20-haoyu-marsboard.dtb \ > > sun7i-a20-hummingbird.dtb \ > > sun7i-a20-itead-ibox.dtb \ > > + sun7i-a20-itead-iteaduino-plus.dts \ > > This should be .dtb. > > Other than that: > Reviewed-by: Jernej Skrabec <jernej.skrabec@xxxxxxxxx> > > I'll fix it while applying. > > For future reference, please follow proper patch submission procedure: > - each revision should be sent in separate thread > - each new revision should contain changelog, either in cover letter (when > there is more than one patch) or below --- line in each patch > - compatible description patch comes before first usage (I'll invert order > when applying) Sorry, I won't apply it as yet. How was this tested if it didn't even built due to mistake in Makefile? Best regards, Jernej > > Best regards, > Jernej > > > sun7i-a20-i12-tvbox.dtb \ > > sun7i-a20-icnova-a20-adb4006.dtb \ > > sun7i-a20-icnova-swac.dtb \ > > diff --git a/arch/arm/boot/dts/allwinner/sun7i-a20-itead-iteaduino-plus.dts b/arch/arm/boot/dts/allwinner/sun7i-a20-itead-iteaduino-plus.dts > > new file mode 100644 > > index 000000000000..c9f9b0275381 > > --- /dev/null > > +++ b/arch/arm/boot/dts/allwinner/sun7i-a20-itead-iteaduino-plus.dts > > @@ -0,0 +1,104 @@ > > +// SPDX-License-Identifier: (GPL-2.0+ or MIT) > > + > > +/dts-v1/; > > +#include "sun7i-a20.dtsi" > > +#include "sunxi-itead-core-common.dtsi" > > + > > +/ { > > + model = "Itead Iteaduino Plus A20"; > > + compatible = "itead,iteaduino-plus-a20", "allwinner,sun7i-a20"; > > + > > + hdmi-connector { > > + compatible = "hdmi-connector"; > > + type = "a"; > > + > > + port { > > + hdmi_con_in: endpoint { > > + remote-endpoint = <&hdmi_out_con>; > > + }; > > + }; > > + }; > > +}; > > + > > +&ac_power_supply { > > + status = "okay"; > > +}; > > + > > +&ahci { > > + target-supply = <®_ahci_5v>; > > + status = "okay"; > > +}; > > + > > +&axp209 { > > + interrupt-parent = <&nmi_intc>; > > + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; > > +}; > > + > > +&battery_power_supply { > > + status = "okay"; > > +}; > > + > > +&codec { > > + stauts = "okay"; > > +}; > > + > > +&de { > > + status = "okay"; > > +}; > > + > > +&emac { > > + pinctrl-names = "default"; > > + pinctrl-0 = <&emac_pa_pins>; > > + phy-handle = <&phy1>; > > + status = "okay"; > > +}; > > + > > +&emac_sram { > > + status = "okay"; > > +}; > > + > > +&hdmi { > > + status = "okay"; > > +}; > > + > > +&hdmi_out { > > + hdmi_out_con: endpoint { > > + remote-endpoint = <&hdmi_con_in>; > > + }; > > +}; > > + > > +&mdio { > > + status = "okay"; > > + > > + phy1: ethernet-phy@1 { > > + reg = <1>; > > + }; > > +}; > > + > > +&mmc0 { > > + vmmc-supply = <®_vcc3v3>; > > + bus-width = <4>; > > + cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */ > > + status = "okay"; > > +}; > > + > > +&otg_sram { > > + status = "okay"; > > +}; > > + > > +®_ahci_5v { > > + status = "okay"; > > +}; > > + > > +®_usb0_vbus { > > + status = "okay"; > > +}; > > + > > +&usb_otg { > > + status = "okay"; > > + dr_mode = "host"; > > +}; > > + > > +&usbphy { > > + usb0_vbus-supply = <®_usb0_vbus>; > > +}; > > -- > > 2.42.0 > > > > > > > > >