Re: [PATCH v4 05/23] interconnect: icc-clk: add support for scaling using OPP

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Tue, 3 Oct 2023 at 17:17, Stephan Gerhold <stephan@xxxxxxxxxxx> wrote:
>
> On Tue, Oct 03, 2023 at 04:36:11PM +0300, Dmitry Baryshkov wrote:
> > On Tue, 3 Oct 2023 at 16:02, Stephan Gerhold <stephan@xxxxxxxxxxx> wrote:
> > >
> > > On Tue, Oct 03, 2023 at 11:30:28AM +0300, Dmitry Baryshkov wrote:
> > > > On 28/08/2023 21:09, Stephen Boyd wrote:
> > > > > Quoting Dmitry Baryshkov (2023-08-27 04:50:15)
> > > > > > diff --git a/drivers/interconnect/icc-clk.c b/drivers/interconnect/icc-clk.c
> > > > > > index d787f2ea36d9..45ffb068979d 100644
> > > > > > --- a/drivers/interconnect/icc-clk.c
> > > > > > +++ b/drivers/interconnect/icc-clk.c
> > > > > > @@ -25,12 +28,16 @@ struct icc_clk_provider {
> > > > > >   static int icc_clk_set(struct icc_node *src, struct icc_node *dst)
> > > > > >   {
> > > > > >          struct icc_clk_node *qn = src->data;
> > > > > > +       unsigned long rate = icc_units_to_bps(src->peak_bw);
> > > > > >          int ret;
> > > > > >          if (!qn || !qn->clk)
> > > > > >                  return 0;
> > > > > > -       if (!src->peak_bw) {
> > > > > > +       if (qn->opp)
> > > > > > +               return dev_pm_opp_set_rate(qn->dev, rate);
> > > > >
> > > > > Just curious how does lockdep do with this? Doesn't OPP call into
> > > > > interconnect code, so lockdep will complain about ABBA?
> > > >
> > > > Unfortunately it does. It seems, the icc-clk is not a proper way to go here.
> > > > I will take a look at reusing set_required_opps for this case.
> > > >
> > >
> > > Could you elaborate a bit which locks exactly cause trouble here?
> > > I'm probably missing something here.
> > >
> > > From a quick look at the OPP code I don't see a global lock taken there
> > > for the entire OPP switch sequence, so I'm not sure how this could cause
> > > an ABBA deadlock.
> >
> > For example:
> >
> > [    7.680041] Chain exists of:
> > [    7.680041]   icc_bw_lock --> regulator_ww_class_acquire --> fs_reclaim
> > [    7.680041]
> > [    7.687955]  Possible unsafe locking scenario:
> > [    7.687955]
> > [    7.699039]        CPU0                    CPU1
> > [    7.704752]        ----                    ----
> > [    7.709266]   lock(fs_reclaim);
> > [    7.713779]                                lock(regulator_ww_class_acquire);
> > [    7.716919]                                lock(fs_reclaim);
> > [    7.724204]   lock(icc_bw_lock);
> >
>
> Hm, I'm not entirely sure how to interpret this. Is there really a
> connection between OPP and ICC here? It looks more like ICC <->
> regulator and somehow related to memory allocations (the fs_reclaim).
>
> Was there more output around this?

[    7.362902] ======================================================
[    7.363447] WARNING: possible circular locking dependency detected
[    7.369434] 6.6.0-rc3-next-20230929-08870-g49503b4b9f55 #129 Not tainted
[    7.375604] ------------------------------------------------------
[    7.382453] swapper/0/1 is trying to acquire lock:
[    7.388437] c143445c (icc_bw_lock){+.+.}-{3:3}, at: icc_init+0x0/0x104
[    7.393225]
[    7.393225] but task is already holding lock:
[    7.399730] c1397444 (fs_reclaim){+.+.}-{0:0}, at: icc_init+0x18/0x104
[    7.405547]
[    7.405547] which lock already depends on the new lock.
[    7.405547]
[    7.412077]
[    7.412077] the existing dependency chain (in reverse order) is:
[    7.420310]
[    7.420310] -> #2 (fs_reclaim){+.+.}-{0:0}:
[    7.427767]        fs_reclaim_acquire+0x60/0x94
[    7.433492]        __kmem_cache_alloc_node+0x30/0x2b4
[    7.437742]        __kmalloc_node_track_caller+0x48/0x244
[    7.442954]        kstrdup+0x30/0x58
[    7.448325]        create_regulator+0x70/0x2b8
[    7.451981]        regulator_resolve_supply+0x3bc/0x7f4
[    7.456234]        regulator_register+0x9b0/0xb50
[    7.461352]        devm_regulator_register+0x50/0x8c
[    7.466216]        rpm_reg_probe+0xf4/0x1a0
[    7.471244]        platform_probe+0x5c/0xb0
[    7.475157]        really_probe+0xc8/0x2d8
[    7.479318]        __driver_probe_device+0x88/0x1a0
[    7.483488]        driver_probe_device+0x30/0x108
[    7.488262]        __driver_attach_async_helper+0x4c/0xa0
[    7.493133]        async_run_entry_fn+0x24/0xb0
[    7.498504]        process_one_work+0x208/0x5e4
[    7.502844]        worker_thread+0x1e0/0x4a4
[    7.507356]        kthread+0x100/0x120
[    7.511874]        ret_from_fork+0x14/0x28
[    7.515428]
[    7.515428] -> #1 (regulator_ww_class_acquire){+.+.}-{0:0}:
[    7.519528]        lock_release+0x164/0x340
[    7.526713]        __mutex_unlock_slowpath+0x3c/0x2fc
[    7.530626]        regulator_lock_dependent+0x1a4/0x298
[    7.535839]        regulator_set_voltage+0x30/0xfc
[    7.540866]        krait_l2_set_one_supply+0x28/0x84
[    7.545729]        krait_l2_config_regulators+0x90/0x1c4
[    7.550851]        _set_opp+0xf0/0x438
[    7.556144]        dev_pm_opp_set_rate+0x118/0x224
[    7.559703]        icc_node_add+0xe8/0x15c
[    7.564474]        icc_clk_register+0x150/0x208
[    7.568556]        krait_l2_probe+0x100/0x114
[    7.572988]        platform_probe+0x5c/0xb0
[    7.577495]        really_probe+0xc8/0x2d8
[    7.581487]        __driver_probe_device+0x88/0x1a0
[    7.585658]        driver_probe_device+0x30/0x108
[    7.590433]        __device_attach_driver+0x94/0x10c
[    7.595300]        bus_for_each_drv+0x84/0xd8
[    7.600326]        __device_attach+0xac/0x1a8
[    7.604580]        bus_probe_device+0x8c/0x90
[    7.608919]        device_add+0x5c8/0x7a4
[    7.613265]        of_platform_device_create_pdata+0x90/0xbc
[    7.617260]        qcom_cpufreq_init+0xa8/0x130
[    7.622984]        do_one_initcall+0x68/0x2d8
[    7.627235]        kernel_init_freeable+0x1ac/0x208
[    7.631752]        kernel_init+0x18/0x12c
[    7.636441]        ret_from_fork+0x14/0x28
[    7.640602]
[    7.640602] -> #0 (icc_bw_lock){+.+.}-{3:3}:
[    7.644607]        __lock_acquire+0x1530/0x28fc
[    7.650413]        lock_acquire+0x10c/0x33c
[    7.654757]        icc_init+0x40/0x104
[    7.658917]        do_one_initcall+0x68/0x2d8
[    7.662740]        kernel_init_freeable+0x1ac/0x208
[    7.667168]        kernel_init+0x18/0x12c
[    7.671855]        ret_from_fork+0x14/0x28
[    7.676018]
[    7.676018] other info that might help us debug this:
[    7.676018]
[    7.680041] Chain exists of:
[    7.680041]   icc_bw_lock --> regulator_ww_class_acquire --> fs_reclaim
[    7.680041]
[    7.687955]  Possible unsafe locking scenario:
[    7.687955]
[    7.699039]        CPU0                    CPU1
[    7.704752]        ----                    ----
[    7.709266]   lock(fs_reclaim);
[    7.713779]                                lock(regulator_ww_class_acquire);
[    7.716919]                                lock(fs_reclaim);
[    7.724204]   lock(icc_bw_lock);
[    7.729833]
[    7.729833]  *** DEADLOCK ***
[    7.729833]
[    7.733071] 1 lock held by swapper/0/1:
[    7.738691]  #0: c1397444 (fs_reclaim){+.+.}-{0:0}, at: icc_init+0x18/0x104
[    7.742528]
[    7.742528] stack backtrace:
[    7.749463] CPU: 3 PID: 1 Comm: swapper/0 Not tainted
6.6.0-rc3-next-20230929-08870-g49503b4b9f55 #129
[    7.754010] Hardware name: Generic DT based system
[    7.763183]  unwind_backtrace from show_stack+0x10/0x14
[    7.767957]  show_stack from dump_stack_lvl+0x60/0x90
[    7.773082]  dump_stack_lvl from check_noncircular+0x174/0x18c
[    7.778288]  check_noncircular from __lock_acquire+0x1530/0x28fc
[    7.784018]  __lock_acquire from lock_acquire+0x10c/0x33c
[    7.790178]  lock_acquire from icc_init+0x40/0x104
[    7.795475]  icc_init from do_one_initcall+0x68/0x2d8
[    7.800159]  do_one_initcall from kernel_init_freeable+0x1ac/0x208
[    7.805286]  kernel_init_freeable from kernel_init+0x18/0x12c
[    7.811361]  kernel_init from ret_from_fork+0x14/0x28
[    7.817177] Exception stack(0xf081dfb0 to 0xf081dff8)

> In general, I would expect that adjusting a regulator from an
> interconnect driver should be made possible somehow. Just because the
> RPM firmware or similar typically handles this internally on Qualcomm
> platforms doesn't mean no one else will ever need to do this. If you
> have a higher bandwidth requests, need to increase the clock, which
> again depends on a higher voltage, then you need to be able to do the
> regulator_set_voltage() from the ICC driver somehow.

This kind of dependency is handled by the consumer, not by the ICC
driver. Usually we explicitly put them to the opp tables, matching
rates and volage.

I think I'll still check the required-opps approach. It will require
manually aggregating the L2 rate requirements, but then we will be
safe from such kinds of interdependencies. And maybe then we can also
rewrite msm8996 to use required-opps too.


-- 
With best wishes
Dmitry




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux