Re: [PATCH v9 0/8] Add StarFive Camera Subsystem driver

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 28/09/2023 10:12, Jack Zhu wrote:
> 
> 
> On 2023/9/15 17:26, Hans Verkuil wrote:
>> On 14/09/2023 05:15, Jack Zhu wrote:
>>> Hi,
>>>
>>> This series is the v9 series that attempts to support the Camera Subsystem
>>> found on StarFive JH7110 SoC.
>>>
>>> This series is based on top of the master branch of media_stage repository.
>>>
>>> The following are the media graph for the device and the v4l2-compliance
>>> output.
>>>
>>> ===========================================================================
>>> [the media graph]:
>>>
>>> digraph board {
>>> 	rankdir=TB
>>> 	n00000001 [label="{{<port0> 0} | stf_isp\n/dev/v4l-subdev0 | {<port1> 1}}", shape=Mrecord, style=filled, fillcolor=green]
>>> 	n00000001:port1 -> n00000008 [style=dashed]
>>> 	n00000004 [label="capture_raw\n/dev/video0", shape=box, style=filled, fillcolor=yellow]
>>> 	n00000008 [label="capture_yuv\n/dev/video1", shape=box, style=filled, fillcolor=yellow]
>>> 	n0000000e [label="{{<port0> 0} | cdns_csi2rx.19800000.csi-bridge\n | {<port1> 1 | <port2> 2 | <port3> 3 | <port4> 4}}", shape=Mrecord, style=filled, fillcolor=green]
>>> 	n0000000e:port1 -> n00000001:port0 [style=dashed]
>>> 	n0000000e:port1 -> n00000004 [style=dashed]
>>> 	n00000018 [label="{{} | imx219 6-0010\n/dev/v4l-subdev1 | {<port0> 0}}", shape=Mrecord, style=filled, fillcolor=green]
>>> 	n00000018:port0 -> n0000000e:port0 [style=bold]
>>> }
>>>
>>> [the device topology]:
>>>
>>> Media controller API version 6.5.0
>>>
>>> Media device information
>>> ------------------------
>>> driver          starfive-camss
>>> model           Starfive Camera Subsystem
>>> serial          
>>> bus info        platform:19840000.camss
>>> hw revision     0x0
>>> driver version  6.5.0
>>>
>>> Device topology
>>> - entity 1: stf_isp (2 pads, 2 links)
>>>             type V4L2 subdev subtype Unknown flags 0
>>>             device node name /dev/v4l-subdev0
>>> 	pad0: Sink
>>> 		[fmt:SRGGB10_1X10/1920x1080 field:none colorspace:srgb
>>> 		 crop.bounds:(0,0)/1920x1080
>>> 		 crop:(0,0)/1920x1080]
>>> 		<- "cdns_csi2rx.19800000.csi-bridge":1 []
>>> 	pad1: Source
>>> 		[fmt:YUYV8_1_5X8/1920x1080 field:none colorspace:srgb
>>> 		 crop.bounds:(0,0)/1920x1080
>>> 		 crop:(0,0)/1920x1080]
>>> 		-> "capture_yuv":0 []
>>>
>>> - entity 4: capture_raw (1 pad, 1 link)
>>>             type Node subtype V4L flags 0
>>>             device node name /dev/video0
>>> 	pad0: Sink
>>> 		<- "cdns_csi2rx.19800000.csi-bridge":1 []
>>>
>>> - entity 8: capture_yuv (1 pad, 1 link)
>>>             type Node subtype V4L flags 0
>>>             device node name /dev/video1
>>> 	pad0: Sink
>>> 		<- "stf_isp":1 []
>>>
>>> - entity 14: cdns_csi2rx.19800000.csi-bridge (5 pads, 3 links)
>>>              type V4L2 subdev subtype Unknown flags 0
>>> 	pad0: Sink
>>> 		<- "imx219 6-0010":0 [ENABLED,IMMUTABLE]
>>> 	pad1: Source
>>> 		-> "stf_isp":0 []
>>> 		-> "capture_raw":0 []
>>> 	pad2: Source
>>> 	pad3: Source
>>> 	pad4: Source
>>>
>>> - entity 24: imx219 6-0010 (1 pad, 1 link)
>>>              type V4L2 subdev subtype Sensor flags 0
>>>              device node name /dev/v4l-subdev1
>>> 	pad0: Source
>>> 		[fmt:SRGGB10_1X10/3280x2464 field:none colorspace:srgb xfer:srgb ycbcr:601 quantization:full-range
>>> 		 crop.bounds:(8,8)/3280x2464
>>> 		 crop:(8,8)/3280x2464]
>>> 		-> "cdns_csi2rx.19800000.csi-bridge":0 [ENABLED,IMMUTABLE]
>>>
>>> ===========================================================================
>>> [the v4l2-compliance output]:
>>>
>>> v4l2-compliance 1.24.1, 64 bits, 64-bit time_t
>>
>> This v4l2-compliance version is from a distro. For driver acceptance you
>> must test with a v4l2-compliance compiled from the git repo (git://linuxtv.org/v4l-utils.git).
>>
>> Also, since this driver uses the media controller, you must run v4l2-compliance
>> with the -m /dev/mediaX option. This will test the compliance of all devices
>> reported by the media controller.
>>
>>>
>>> Compliance test for stf camss device /dev/video1:
>>>
>>> Driver Info:
>>> 	Driver name      : stf camss
>>
>> The module is called starfive-camss, so shouldn't the driver name reported here
>> be the same?
>>
>>> 	Card type        : Starfive Camera Subsystem
>>> 	Bus info         : platform:19840000.camss
>>> 	Driver version   : 6.5.0
>>> 	Capabilities     : 0x84200001
>>> 		Video Capture
>>> 		Streaming
>>> 		Extended Pix Format
>>> 		Device Capabilities
>>> 	Device Caps      : 0x04200001
>>> 		Video Capture
>>> 		Streaming
>>> 		Extended Pix Format
>>> Media Driver Info:
>>> 	Driver name      : starfive-camss
>>
>> It's correct in the media controller information.
>>
>>> 	Model            : Starfive Camera Subsystem
>>> 	Serial           : 
>>> 	Bus info         : platform:19840000.camss
>>> 	Media version    : 6.5.0
>>> 	Hardware revision: 0x00000000 (0)
>>> 	Driver version   : 6.5.0
>>> Interface Info:
>>> 	ID               : 0x0300000a
>>> 	Type             : V4L Video
>>> Entity Info:
>>> 	ID               : 0x00000008 (8)
>>> 	Name             : capture_yuv
>>> 	Function         : V4L2 I/O
>>> 	Pad 0x01000009   : 0: Sink
>>> 	  Link 0x0200000c: from remote pad 0x1000003 of entity 'stf_isp' (Unknown Function (00004009)): Data, Enabled
>>
>> Hmm, this reports "Unknown Function". I bet that when you run v4l2-compliance
>> with the -m option it will fail on this. If not, then that's likely a bug in
>> the compliance test, please let me know if that's the case.
>>
> 
> Hi Hans,
> 
> The following is the latest test log, which does not report a failure, but
> also reports "Unknown Function".
> 
> I make the following settings in the stf-isp.c file:
> v4l2_subdev.entity.function = MEDIA_ENT_F_PROC_VIDEO_ISP;
> 

Can you post the output of:

v4l2-compliance --verbose -M /dev/media0

I am beginning to suspect that utils/common/media-info.cpp is out-of-date:
it is missing MEDIA_ENT_F_PROC_VIDEO_ISP.

But I don't understand why v4l2-compliance didn't fail on this.

Regards,

	Hans




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux