Dne sreda, 27. september 2023 ob 16:14:03 CEST je Chris Morgan napisal(a):
> On Mon, Sep 25, 2023 at 06:00:46PM +0200, Jernej Škrabec wrote:
> > Dne ponedeljek, 25. september 2023 ob 17:00:33 CEST je Chris Morgan napisal(a):
> > > On Sun, Sep 24, 2023 at 09:33:53PM +0200, Jernej Škrabec wrote:
> > > > Dne četrtek, 21. september 2023 ob 15:51:36 CEST je Chris Morgan napisal(a):
> > > > > From: Chris Morgan <macromorgan@xxxxxxxxxxx>
> > > > >
> > > > > The Anbernic RG-Nano is a small portable game device based on the
> > > > > Allwinner V3s SoC. It has GPIO buttons on the face and side for
> > > > > input, a single mono speaker, a 240x240 SPI controlled display, a USB-C
> > > > > OTG port, an SD card slot for booting, and 64MB of RAM included in the
> > > > > SoC. There does not appear to be a crystal feeding the internal RTC so
> > > > > it does not keep proper time (for me it ran 8 hours slow in a 24 hour
> > > > > period). External RTC works just fine.
> > > > >
> > > > > Working/Tested:
> > > > > - SDMMC
> > > > > - UART (for debugging)
> > > > > - Buttons
> > > > > - Charging/battery/PMIC
> > > > > - Speaker
> > > > > - RTC (external RTC)
> > > > > - USB
> > > > > - Display
> > > > >
> > > > > Signed-off-by: Chris Morgan <macromorgan@xxxxxxxxxxx>
> > > > > ---
> > > > > arch/arm/boot/dts/allwinner/Makefile | 1 +
> > > > > .../allwinner/sun8i-v3s-anbernic-rg-nano.dts | 284 ++++++++++++++++++
> > > > > 2 files changed, 285 insertions(+)
> > > > > create mode 100644 arch/arm/boot/dts/allwinner/sun8i-v3s-anbernic-rg-nano.dts
> > > > >
> > > > > diff --git a/arch/arm/boot/dts/allwinner/Makefile b/arch/arm/boot/dts/allwinner/Makefile
> > > > > index eebb5a0c873a..2d26c3397f14 100644
> > > > > --- a/arch/arm/boot/dts/allwinner/Makefile
> > > > > +++ b/arch/arm/boot/dts/allwinner/Makefile
> > > > > @@ -256,6 +256,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \
> > > > > sun8i-t113s-mangopi-mq-r-t113.dtb \
> > > > > sun8i-t3-cqa3t-bv3.dtb \
> > > > > sun8i-v3-sl631-imx179.dtb \
> > > > > + sun8i-v3s-anbernic-rg-nano.dtb \
> > > > > sun8i-v3s-licheepi-zero.dtb \
> > > > > sun8i-v3s-licheepi-zero-dock.dtb \
> > > > > sun8i-v40-bananapi-m2-berry.dtb
> > > > > diff --git a/arch/arm/boot/dts/allwinner/sun8i-v3s-anbernic-rg-nano.dts b/arch/arm/boot/dts/allwinner/sun8i-v3s-anbernic-rg-nano.dts
> > > > > new file mode 100644
> > > > > index 000000000000..1a4429dc57b1
> > > > > --- /dev/null
> > > > > +++ b/arch/arm/boot/dts/allwinner/sun8i-v3s-anbernic-rg-nano.dts
> > > > > @@ -0,0 +1,284 @@
> > > > > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> > > > > +
> > > > > +/dts-v1/;
> > > > > +#include <dt-bindings/input/linux-event-codes.h>
> > > > > +#include "sun8i-v3s.dtsi"
> > > > > +#include "sunxi-common-regulators.dtsi"
> > > > > +
> > > > > +/ {
> > > > > + model = "Anbernic RG Nano";
> > > > > + compatible = "anbernic,rg-nano", "allwinner,sun8i-v3s";
> > > > > +
> > > > > + aliases {
> > > > > + rtc0 = &pcf8563;
> > > > > + rtc1 = &rtc;
> > > > > + serial0 = &uart0;
> > > > > + };
> > > > > +
> > > > > + backlight: backlight {
> > > > > + compatible = "pwm-backlight";
> > > > > + brightness-levels = <0 1 2 3 8 14 21 32 46 60 80 100>;
> > > > > + default-brightness-level = <11>;
> > > > > + power-supply = <®_vcc5v0>;
> > > > > + pwms = <&pwm 0 40000 1>;
> > > > > + };
> > > > > +
> > > > > + chosen {
> > > > > + stdout-path = "serial0:115200n8";
> > > > > + };
> > > > > +
> > > > > + gpio_keys: gpio-keys {
> > > > > + compatible = "gpio-keys";
> > > > > +
> > > > > + button-a {
> > > > > + gpios = <&gpio_expander 12 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
> > > > > + label = "BTN-A";
> > > > > + linux,code = <BTN_EAST>;
> > > > > + };
> > > > > +
> > > > > + button-b {
> > > > > + gpios = <&gpio_expander 14 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
> > > > > + label = "BTN-B";
> > > > > + linux,code = <BTN_SOUTH>;
> > > > > + };
> > > > > +
> > > > > + button-down {
> > > > > + gpios = <&gpio_expander 1 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
> > > > > + label = "DPAD-DOWN";
> > > > > + linux,code = <BTN_DPAD_DOWN>;
> > > > > + };
> > > > > +
> > > > > + button-left {
> > > > > + gpios = <&gpio_expander 4 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
> > > > > + label = "DPAD-LEFT";
> > > > > + linux,code = <BTN_DPAD_LEFT>;
> > > > > + };
> > > > > +
> > > > > + button-right {
> > > > > + gpios = <&gpio_expander 0 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
> > > > > + label = "DPAD-RIGHT";
> > > > > + linux,code = <BTN_DPAD_RIGHT>;
> > > > > + };
> > > > > +
> > > > > + button-se {
> > > > > + gpios = <&gpio_expander 7 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
> > > > > + label = "BTN-SELECT";
> > > > > + linux,code = <BTN_SELECT>;
> > > > > + };
> > > > > +
> > > > > + button-st {
> > > > > + gpios = <&gpio_expander 6 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
> > > > > + label = "BTN-START";
> > > > > + linux,code = <BTN_START>;
> > > > > + };
> > > > > +
> > > > > + button-tl {
> > > > > + gpios = <&gpio_expander 2 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
> > > > > + label = "BTN-L";
> > > > > + linux,code = <BTN_TL>;
> > > > > + };
> > > > > +
> > > > > + button-tr {
> > > > > + gpios = <&gpio_expander 15 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
> > > > > + label = "BTN-R";
> > > > > + linux,code = <BTN_TR>;
> > > > > + };
> > > > > +
> > > > > + button-up {
> > > > > + gpios = <&gpio_expander 3 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
> > > > > + label = "DPAD-UP";
> > > > > + linux,code = <BTN_DPAD_UP>;
> > > > > + };
> > > > > +
> > > > > + button-x {
> > > > > + gpios = <&gpio_expander 11 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
> > > > > + label = "BTN-X";
> > > > > + linux,code = <BTN_NORTH>;
> > > > > + };
> > > > > +
> > > > > + button-y {
> > > > > + gpios = <&gpio_expander 13 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
> > > > > + label = "BTN-Y";
> > > > > + linux,code = <BTN_WEST>;
> > > > > + };
> > > > > + };
> > > > > +};
> > > > > +
> > > > > +&codec {
> > > > > + allwinner,audio-routing = "Speaker", "HP",
> > > > > + "MIC1", "Mic",
> > > > > + "Mic", "HBIAS";
> > > > > + allwinner,pa-gpios = <&pio 5 6 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PF6 */
> > > > > + status = "okay";
> > > > > +};
> > > > > +
> > > > > +&ehci {
> > > > > + status = "okay";
> > > > > +};
> > > > > +
> > > > > +&i2c0 {
> > > > > + status = "okay";
> > > > > +
> > > > > + gpio_expander: gpio@20 {
> > > > > + compatible = "nxp,pcal6416";
> > > > > + reg = <0x20>;
> > > > > + gpio-controller;
> > > > > + #gpio-cells = <2>;
> > > > > + #interrupt-cells = <2>;
> > > > > + interrupt-controller;
> > > > > + interrupt-parent = <&pio>;
> > > > > + interrupts = <1 3 IRQ_TYPE_EDGE_BOTH>; /* PB3/EINT3 */
> > > > > + vcc-supply = <®_vcc3v3>;
> > > > > + };
> > > > > +
> > > > > + axp209: pmic@34 {
> > > > > + reg = <0x34>;
> > > > > + interrupt-parent = <&pio>;
> > > > > + interrupts = <1 5 IRQ_TYPE_EDGE_FALLING>; /* PB5/EINT5 */
> > > > > + };
> > > > > +
> > > > > + pcf8563: rtc@51 {
> > > > > + compatible = "nxp,pcf8563";
> > > > > + reg = <0x51>;
> > > > > + };
> > > > > +};
> > > > > +
> > > > > +#include "axp209.dtsi"
> > > > > +
> > > > > +&battery_power_supply {
> > > > > + status = "okay";
> > > > > +};
> > > > > +
> > > > > +&mmc0 {
> > > > > + broken-cd;
> > > > > + bus-width = <4>;
> > > > > + disable-wp;
> > > > > + vmmc-supply = <®_vcc3v3>;
> > > > > + vqmmc-supply = <®_vcc3v3>;
> > > > > + status = "okay";
> > > > > +};
> > > > > +
> > > > > +&ohci {
> > > > > + status = "okay";
> > > > > +};
> > > > > +
> > > > > +&pio {
> > > > > + vcc-pb-supply = <®_vcc3v3>;
> > > > > + vcc-pc-supply = <®_vcc3v3>;
> > > > > + vcc-pf-supply = <®_vcc3v3>;
> > > > > + vcc-pg-supply = <®_vcc3v3>;
> > > > > +
> > > > > + spi0_no_miso_pins: spi0-no-miso-pins {
> > > > > + pins = "PC1", "PC2", "PC3";
> > > > > + function = "spi0";
> > > > > + };
> > > > > +};
> > > > > +
> > > > > +&pwm {
> > > > > + pinctrl-0 = <&pwm0_pin>;
> > > > > + pinctrl-names = "default";
> > > > > + status = "okay";
> > > > > +};
> > > > > +
> > > > > +/* DCDC2 wired into vdd-cpu, vdd-sys, and vdd-ephy. */
> > > > > +®_dcdc2 {
> > > > > + regulator-always-on;
> > > > > + regulator-max-microvolt = <1250000>;
> > > > > + regulator-min-microvolt = <1250000>;
> > > > > + regulator-name = "vdd-cpu";
> > > > > +};
> > > > > +
> > > > > +/* DCDC3 wired into every 3.3v input that isn't the RTC. */
> > > > > +®_dcdc3 {
> > > > > + regulator-always-on;
> > > > > + regulator-max-microvolt = <3300000>;
> > > > > + regulator-min-microvolt = <3300000>;
> > > > > + regulator-name = "vcc-io";
> > > > > +};
> > > > > +
> > > > > +/*
> > > > > + * LDO1 wired into RTC, voltage is hard-wired at 3.3v and cannot be
> > > > > + * software modified. Note that setting voltage here to 3.3v for accuracy
> > > > > + * sake causes an issue with the driver that causes it to fail to probe
> > > > > + * because of a voltage constraint in the driver.
> > > > > + */
> > > >
> > > > Can you please remove any mention of drivers everywhere? DT is OS and
> > > > thus driver independent.
> > > >
> > > > Once fixed:
> > > > Acked-by: Jernej Skrabec <jernej.skrabec@xxxxxxxxx>
> > >
> > > This note was added due to prior comments because in this very specific
> > > case we're working around a driver issue. Sadly if I accurately
> > > describe the hardware the PMIC and devices that depend on it will fail
> > > to probe (the hardware is 3.3v, but here it's set as 1.3v).
> > >
> > > https://lore.kernel.org/linux-sunxi/20230629203410.660eb9a4@xxxxxxxxxxxx/
> >
> > Sorry, I should follow conversation more closely. Procedure in such cases
> > is to fix driver first and then submit proper DT file. While DT files
> > reside in Linux source, they are often used by diferent projects, like
> > U-Boot or FreeBSD, so we can't make hacks just because Linux driver doesn't
> > work.
>
> I'll drop all but the note that "LDO1 is wired into RTC and voltage is
> hard wired at 3.3v". That accurately describes the hardware, so will
> that work?
OK.
Best regards,
Jernej
>
> >
> > >
> > > Thank you,
> > > Chris
> > >
> > > >
> > > > Best regards,
> > > > Jernej
> > > >
> > > > > +®_ldo1 {
> > > > > + regulator-always-on;
> > > > > + regulator-name = "vcc-rtc";
> > > > > +};
> > > > > +
> > > > > +/* LDO2 wired into VCC-PLL and audio codec. */
> > > > > +®_ldo2 {
> > > > > + regulator-always-on;
> > > > > + regulator-max-microvolt = <3000000>;
> > > > > + regulator-min-microvolt = <3000000>;
> > > > > + regulator-name = "vcc-pll";
> > > > > +};
> > > > > +
> > > > > +/* LDO3, LDO4, and LDO5 unused. */
> > > > > +®_ldo3 {
> > > > > + status = "disabled";
> > > > > +};
> > > > > +
> > > > > +®_ldo4 {
> > > > > + status = "disabled";
> > > > > +};
> > > > > +
> > > > > +/*
> > > > > + * Force the driver to use internal oscillator by removing clocks
> > > > > + * property.
> > > > > + */
> >
> > This should be reworded to avoid mentioning driver. Like: "RTC uses
> > internal oscillator".
> >
> > Best regards,
> > Jernej
> >
>
> You got it.
>
> > > > > +&rtc {
> > > > > + /delete-property/ clocks;
> > > > > +};
> > > > > +
> > > > > +&spi0 {
> > > > > + pinctrl-0 = <&spi0_no_miso_pins>;
> > > > > + pinctrl-names = "default";
> > > > > + status = "okay";
> > > > > +
> > > > > + display@0 {
> > > > > + compatible = "saef,sftc154b", "panel-mipi-dbi-spi";
> > > > > + reg = <0>;
> > > > > + backlight = <&backlight>;
> > > > > + dc-gpios = <&pio 2 0 GPIO_ACTIVE_HIGH>; /* PC0 */
> > > > > + reset-gpios = <&pio 1 2 GPIO_ACTIVE_HIGH>; /* PB2 */
> > > > > + spi-max-frequency = <100000000>;
> > > > > +
> > > > > + height-mm = <39>;
> > > > > + width-mm = <39>;
> > > > > +
> > > > > + /* Set hb-porch to compensate for non-visible area */
> > > > > + panel-timing {
> > > > > + hactive = <240>;
> > > > > + vactive = <240>;
> > > > > + hback-porch = <80>;
> > > > > + vback-porch = <0>;
> > > > > + clock-frequency = <0>;
> > > > > + hfront-porch = <0>;
> > > > > + hsync-len = <0>;
> > > > > + vfront-porch = <0>;
> > > > > + vsync-len = <0>;
> > > > > + };
> > > > > + };
> > > > > +};
> > > > > +
> > > > > +&uart0 {
> > > > > + pinctrl-0 = <&uart0_pb_pins>;
> > > > > + pinctrl-names = "default";
> > > > > + status = "okay";
> > > > > +};
> > > > > +
> > > > > +&usb_otg {
> > > > > + dr_mode = "otg";
> > > > > + status = "okay";
> > > > > +};
> > > > > +
> > > > > +&usb_power_supply {
> > > > > + status = "okay";
> > > > > +};
> > > > > +
> > > > > +&usbphy {
> > > > > + usb0_id_det-gpios = <&pio 6 5 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PG5 */
> > > > > + status = "okay";
> > > > > +};
> > > > >
> > > >
> > > >
> > > >
> > > >
> > >
> >
> >
> >
> >
>
> Thank you,
> Chris
>
