On Tue, Sep 26, 2023 at 2:48 AM Miquel Raynal <miquel.raynal@xxxxxxxxxxx> wrote: > > Hello, > > > > > > > These are firmware bindings, as indicated, but I > > > > > > took them out of the /firmware node since that is for a different > > > > > > purpose. Rob suggested that partitions was a good place. We have fwupd > > > > > > using DT to hold the firmware-update information, so I expect it will > > > > > > move to use these bindings too. > > > > > > > > > > I would definitely use fixed partitions as that's what you need then: > > > > > registering where everything starts and ends. If you have "in-band" > > > > > meta data you might require a compatible, but I don't think you > > > > > do, in this case you should probably carry the content through a label > > > > > (which will become the partition name) and we can discuss additional > > > > > properties if needed. > > > > > > > > I believe I am going to need a compatible string at the 'partitions' > > > > level to indicate that this is the binman scheme. But we can leave > > > > that until later. > > > > > > Perhaps: > > > > > > compatible = "binman", "fixed-partitions"; > > > > > > Though I don't understand why binman couldn't just understand what > > > "fixed-partitions" means rather than "binman". > > > > Well so long as we don't add any binman things in here, you are right. > > > > But the eventual goal is parity with current Binman functionality, > > which writes the entire (augmented) description to the DT, allowing > > tools to rebuild / repack / replace pieces later, maintaining the same > > alignment constraints, etc. I am assuming that properties like 'align > > = <16>' would not fit with fixed-partitions. > > I am personally not bothered by this kind of properties. But if we plan > on adding too much properties, I will advise to indeed use another name > than fixed-partitions (or add the "binman" secondary compatible) > otherwise it's gonna be hard to support in the code while still > restraining as much as we can the other partition schema. Agreed. It's a trade off. I think we need enough to understand the problem (not just presented with a solution), agree on the general solution/direction, and then discuss specific additions. > > But if we don't preserve > > these properties then Binman cannot do repacking reliably. Perhaps for > > now I could put the augmented DT in its own section somewhere, but I > > am just not sure if that will work in a real system. E.g. with VBE the > > goal is to use the DT to figure out how to access the firmware, update > > it, etc. VBE? > > Is it not possible to have my own node with whatever things Binman > > needs in it (subject to review of course)? i.e. could we discuss how > > to encode it, but argue less about whether things are needed? I > > kind-of feel I know what is needed, since I wrote the tool. What we don't need is the same information in 2 places for the DTB used at runtime. If the binman node is removed, do whatever you want. If you want to keep it at runtime, then it's got to extend what we already have. I don't think anyone is disagreeing about whether specific information is needed or not. > > > > So you are suggesting 'label' for the contents. Rob suggested > > > > 'compatible' [1], so what should I do? > > > > > > "label" is for consumption by humans, not tools/software. Compatible > > > values are documented, label values are not. Though the partition > > > stuff started out using label long ago and it's evolved to preferring > > > compatible. > > > > OK so we are agreed that we are going with 'compatible'. > > Still strongly disagree here. Miquel is right. I was confused here. "label" is still pretty much used for what the image is. Though we do have "u-boot,env" for both it seems. My position on "label" stands. To the extent we have images for common components, I think we should standardize the names. Certainly if tools rely on the names, then they should be documented. > My understanding is that a compatible carries how the content is > organized, and how this maybe specific (like you have in-band meta data > data that needs to be parsed in a specific way or in your case > additional specific properties in the DT which give more context about > how the data is stored). But the real content of the partition, ie. if > it contains a firmware, the kernel or some user data does not belong to > the compatible. > > I.e: > - The first byte of my partition gives the compression algorithm: > -> compatible = "compressed-partition-foo"; > or > -> compatible = "fixed-partitions" + compression-algorithm = "foo"; > - The partition contains a picture of my dog: > -> label = "my dog is beautiful" > but certainly not > -> compatible = "my-dog"; IMO, compatible in this case should convey "JPEG image" or similar. > I don't see why, for the binman schema, we could not constrain the > labels? Yes, but those should follow what we already have. "u-boot" for example rather than "data,u-boot" which I think Simon had in some version of this. Rob
