On 9/25/2023 7:15 PM, Andrew Davis wrote:
> On 9/25/23 3:21 AM, MD Danish Anwar wrote:
>> Hi Andrew,
>>
>> On 22/09/23 09:52, MD Danish Anwar wrote:
>>> On 21/09/23 22:57, Andrew Davis wrote:
>>>> On 9/21/23 1:09 AM, MD Danish Anwar wrote:
>>>>> ICSSG2 provides dual Gigabit Ethernet support.
>>>>>
>>>>> For support SR2.0 ICSSG Ethernet firmware:
>>>>> - provide different firmware blobs and use TX_PRU.
>>>>> - IEP0 is used as PTP Hardware Clock and can only be used for one
>>>>> port.
>>>>> - TX timestamp notification comes via INTC interrupt.
>>>>>
>>>>> Signed-off-by: MD Danish Anwar <danishanwar@xxxxxx>
>>>>> ---
>>>>> arch/arm64/boot/dts/ti/Makefile | 4 +-
>>>>> ...se-board.dts => k3-am654-common-board.dts} | 0
>>>>> arch/arm64/boot/dts/ti/k3-am654-icssg2.dtso | 145
>>>>> ++++++++++++++++++
>>>>> 3 files changed, 148 insertions(+), 1 deletion(-)
>>>>> rename arch/arm64/boot/dts/ti/{k3-am654-base-board.dts =>
>>>>> k3-am654-common-board.dts} (100%)
>>>>> create mode 100644 arch/arm64/boot/dts/ti/k3-am654-icssg2.dtso
>>>>>
>>>>> diff --git a/arch/arm64/boot/dts/ti/Makefile
>>>>> b/arch/arm64/boot/dts/ti/Makefile
>>>>> index e7b8e2e7f083..85c91f5e832e 100644
>>>>> --- a/arch/arm64/boot/dts/ti/Makefile
>>>>> +++ b/arch/arm64/boot/dts/ti/Makefile
>>>>> @@ -42,12 +42,14 @@ dtb-$(CONFIG_ARCH_K3) +=
>>>>> k3-am642-tqma64xxl-mbax4xxl-sdcard.dtb
>>>>> dtb-$(CONFIG_ARCH_K3) += k3-am642-tqma64xxl-mbax4xxl-wlan.dtb
>>>>> # Boards with AM65x SoC
>>>>> -k3-am654-gp-evm-dtbs := k3-am654-base-board.dtb
>>>>> k3-am654-base-board-rocktech-rk101-panel.dtbo
>>>>> +k3-am654-gp-evm-dtbs := k3-am654-common-board.dtb
>>>>> k3-am654-base-board-rocktech-rk101-panel.dtbo
>>>>
>>>> Should the k3-am654-gp-evm.dtb not also have this icssg2 support? Does
>>>> it work
>>>> to keep this line like before or is there some conflict having both
>>>> enabled?
>>>>
>>>
>>> I have not tested this dtb (k3-am654-gp-evm.dtb). So just to be on the
>>> safe side I kept gp-evm.dtb as it was. Ideally gp-evm.dtb should have
>>> icssg2 support as well. But I haven't tested the combination of
>>> base-board + icssg dtbo + rockteck dtbo. That is why I kept gp-evm dtb
>>> as it was. Anyways, for ICSSG2's use case only k3-am654-base-board.dtb
>>> is used so I think it's ok to leave k3-am654-gp-evm.dtb to as it was.
>>>
>>>> Andrew
>>>>
>>
>> I tested AM654x-GP EVM with k3-am654-gp-evm.dtb with both the
>> combination below (having k3-am654-base-board-dtbs :=
>> k3-am654-common-board.dtb k3-am654-icssg2.dtbo), ICSSG worked fine in
>> both the scenarios and I didn't see any issue. I don't have a rocktech
>> panel with me so couldn't test that. But as far as ICSSG is concerned it
>> works fine with the both the combinations. Please let me know which one
>> should I use. Should I keep gp-evm as it is (use dtb without the icssg2
>> overlay) or should I add icssg2 overlay in gp-evm.dtb as well.
>>
>>
>> 1. k3-am654-gp-evm-dtbs := k3-am654-base-board.dtb
>> k3-am654-base-board-rocktech-rk101-panel.dtbo
>>
>>
>> 2. k3-am654-gp-evm-dtbs := k3-am654-common-board.dtb
>> k3-am654-base-board-rocktech-rk101-panel.dtbo
>>
>
> As you said here before, most will expect the icssg2 to work
> on the EVM out of box, you should include it. If anyone wants
> something else they can apply the set of overlays that match
> on their own.
>
> So, use base-board.
>
> Andrew
Sure Andrew, I will make the change and send v3.
--
Thanks and Regards,
Md Danish Anwar
