On Fri, 22 Sep 2023 14:19:10 +0300
Matti Vaittinen <mazziesaccount@xxxxxxxxx> wrote:
> Support for the ROHM BM1390 pressure sensor. The BM1390GLV-Z can measure
> pressures ranging from 300 hPa to 1300 hPa with configurable measurement
> averaging and internal FIFO. The sensor does also provide temperature
> measurements.
>
> Sensor does also contain IIR filter implemented in HW. The data-sheet
> says the IIR filter can be configured to be "weak", "middle" or
> "strong". Some RMS noise figures are provided in data sheet but no
> accurate maths for the filter configurations is provided. Hence, the IIR
> filter configuration is not supported by this driver and the filter is
> configured to the "middle" setting (at least not for now).
>
> The FIFO measurement mode is only measuring the pressure and not the
> temperature. The driver measures temperature when FIFO is flushed and
> simply uses the same measured temperature value to all reported
> temperatures. This should not be a problem when temperature is not
> changing very rapidly (several degrees C / second) but allows users to
> get the temperature measurements from sensor without any additional logic.
>
> This driver allows the sensor to be used in two muitually exclusive ways,
>
> 1. With trigger (data-ready IRQ).
> In this case the FIFO is not used as we get data ready for each collected
> sample. Instead, for each data-ready IRQ we read the sample from sensor
> and push it to the IIO buffer.
>
> 2. With hardware FIFO and watermark IRQ.
> In this case the data-ready is not used but we enable watermark IRQ. At
> each watermark IRQ we go and read all samples in FIFO and push them to the
> IIO buffer.
>
> Signed-off-by: Matti Vaittinen <mazziesaccount@xxxxxxxxx>
Main question here is whether the fifo mode is useable if now interrupt
is wired up? I'm guessing not really as it's not worth dealing with making
it work if someone can't be bothered to connect the wire. In which case
I'd expect few more things to be disable if no IRQ.
Also, didn't think we'd have a validate_own_trigger callback set
as that means the buffer is potentially also something that should go
away if no interrupts are wired.
Anyhow, other than that a few trivial things inline.
Jonathan
>
> ---
> Revision history:
>
> v2 => v3:
> - Read temperature only after FIFO is read to overcome a HW quirck
> - Drop unused defines
> - Allow scanning the pressure only
> - Some clarifying comments added, some made less verbose
> - warn if measurement stp fails
> - use IIO_VAL_FRACTIONAL for pressure scale
> - don't disable IRQ but use timestamp from stack
> - fix amount of samples to read
> - minor styling
> - better separate buffer and trigger parts
> - allow buffer even when there is no IRQ
> with external trigger to be supported.
> - add completely, utterly useless NULL check because we have the cycles
> to waste (grumbles)
)Smiles)
> diff --git a/drivers/iio/pressure/Makefile b/drivers/iio/pressure/Makefile
> index c90f77210e94..436aec7e65f3 100644
> --- a/drivers/iio/pressure/Makefile
> +++ b/drivers/iio/pressure/Makefile
> @@ -5,6 +5,7 @@
>
> # When adding new entries keep the list in alphabetical order
> obj-$(CONFIG_ABP060MG) += abp060mg.o
> +obj-$(CONFIG_ROHM_BM1390) += rohm-bm1390.o
> obj-$(CONFIG_BMP280) += bmp280.o
> bmp280-objs := bmp280-core.o bmp280-regmap.o
> obj-$(CONFIG_BMP280_I2C) += bmp280-i2c.o
> diff --git a/drivers/iio/pressure/rohm-bm1390.c b/drivers/iio/pressure/rohm-bm1390.c
> new file mode 100644
> index 000000000000..82a0cd61d215
> --- /dev/null
> +++ b/drivers/iio/pressure/rohm-bm1390.c
> +
> +/*
> + * If the trigger is not used we just wait until the measurement has
> + * completed. The data-sheet says maximum measurement cycle (regardless
> + * the AVE_NUM) is 200 mS so let's just sleep at least that long. If speed
> + * is needed the trigger should be used.
> + */
> +#define BM1390_MAX_MEAS_TIME_MS 205
> +
> +static int bm1390_read_data(struct bm1390_data *data,
> + struct iio_chan_spec const *chan, int *val, int *val2)
> +{
> + int ret, warn;
> +
> + mutex_lock(&data->mutex);
> + /*
> + * We use 'continuous mode' even for raw read because according to the
> + * data-sheet an one-shot mode can't be used with IIR filter.
> + */
> + ret = bm1390_meas_set(data, BM1390_MEAS_MODE_CONTINUOUS);
> + if (ret)
> + goto unlock_out;
> +
> + switch (chan->type) {
> + case IIO_PRESSURE:
> + msleep(BM1390_MAX_MEAS_TIME_MS);
> + ret = bm1390_pressure_read(data, val);
> + break;
> + case IIO_TEMP:
> + msleep(BM1390_MAX_MEAS_TIME_MS);
> + ret = bm1390_read_temp(data, val);
> + break;
> + default:
> + ret = -EINVAL;
> + }
> + warn = bm1390_meas_set(data, BM1390_MEAS_MODE_STOP);
> + if (warn)
> + dev_warn(data->dev, "Failed to stop measurementi (%d)\n", warn);
measurement
> +unlock_out:
> + mutex_unlock(&data->mutex);
> +
> + return ret;
> +}
> +
> +static int __bm1390_fifo_flush(struct iio_dev *idev, unsigned int samples,
> + s64 timestamp)
> +{
> + /* BM1390_FIFO_LENGTH is small so we shouldn't run out of stack */
> + struct bm1390_data_buf buffer[BM1390_FIFO_LENGTH];
> + struct bm1390_data *data = iio_priv(idev);
> + int smp_lvl, ret, i, warn, dummy;
> + u64 sample_period;
> + __be16 temp = 0;
> +
> + ret = regmap_read(data->regmap, BM1390_REG_FIFO_LVL, &smp_lvl);
> + if (ret)
> + return ret;
> +
> + smp_lvl = FIELD_GET(BM1390_MASK_FIFO_LVL, smp_lvl);
> + if (!smp_lvl)
> + return 0;
> +
> + if (smp_lvl > BM1390_FIFO_LENGTH) {
> + /*
> + * The fifo holds maximum of 4 samples so valid values
> + * should be 0, 1, 2, 3, 4 - rest are probably bit errors
> + * in I2C line. Don't overflow if this happens.
> + */
> + dev_err(data->dev, "bad FIFO level %d\n", smp_lvl);
> + smp_lvl = BM1390_FIFO_LENGTH;
> + }
> +
> + sample_period = timestamp - data->old_timestamp;
> + do_div(sample_period, smp_lvl);
> +
> + if (samples && smp_lvl > samples)
> + smp_lvl = samples;
> +
> +
> + /*
> + * After some testing it appears that the temperature is not readable
> + * untill the FIFO access has been done after the WMI. Thus, we need
Spell check. until (Why it doesn't have 2 ls is beyond me but that's English being
annoyingly irregular)
> + * to read the all pressure values to memory and read the temperature
> + * only after that.
> + */
> + for (i = 0; i < smp_lvl; i++) {
> + /*
> + * When we start reading data from the FIFO the sensor goes to
> + * special FIFO reading mode. If any other register is accessed
> + * during the FIFO read, samples can be dropped. Prevent access
> + * until FIFO_LVL is read. We have mutex locked and we do also
> + * go performing reading of FIFO_LVL even if this read fails.
> + */
> + if (test_bit(BM1390_CHAN_PRESSURE, idev->active_scan_mask)) {
> + ret = bm1390_pressure_read(data, &buffer[i].pressure);
> + if (ret)
> + break;
> + }
> +
> + /*
> + * Old timestamp is either the previous sample IRQ time,
> + * previous flush-time or, if this was first sample, the enable
> + * time. When we add a sample period to that we should get the
> + * best approximation of the time-stamp we are handling.
> + *
> + * Idea is to always keep the "old_timestamp" matching the
> + * timestamp which we are currently handling.
> + */
> + data->old_timestamp += sample_period;
> + buffer[i].ts = data->old_timestamp;
> + }
> + /* Reading the FIFO_LVL closes the FIFO access sequence */
> + warn = regmap_read(data->regmap, BM1390_REG_FIFO_LVL, &dummy);
> + if (warn)
> + dev_warn(data->dev, "Closing FIFO sequence failed\n");
> +
> + if (ret)
> + return ret;
> +
> + if (test_bit(BM1390_CHAN_TEMP, idev->active_scan_mask)) {
> + ret = regmap_bulk_read(data->regmap, BM1390_REG_TEMP_HI, &temp,
> + sizeof(temp));
> + if (ret)
> + return ret;
> + pr_info("Temp before reading the FIFO %u\n", be16_to_cpu(temp));
Why this print?
> + }
> +
> + if (ret)
> + return ret;
> +
> + for (i = 0; i < smp_lvl; i++) {
> + buffer[i].temp = temp;
> + iio_push_to_buffers_with_timestamp(idev, &buffer[i],
> + buffer[i].ts);
You can just use iio_push_to_buffers() if you've already filled
in the timestamp by hand. The _with_timestamp() version was just to reduce
boilerplate (and given the main it has caused over the years, I'm not
sure it was a good idea!)
> + }
> +
> + return smp_lvl;
> +}
> +
> +static const struct iio_info bm1390_info = {
> + .read_raw = &bm1390_read_raw,
> + .validate_trigger = iio_validate_own_trigger,
> + .hwfifo_set_watermark = bm1390_set_watermark,
> + .hwfifo_flush_to_buffer = bm1390_fifo_flush,
Given my (possibly incorrect assumption) that the fifo is useless
without the interrupt, I'd expect to see another version of this
that has read_raw only set.
Also, why do we need validate_own_trigger. I thought this could
be used with other triggers. If not, then don't register the buffer
for the case with no interrupt either.
> +};
> +
> +
> +static int bm1390_fifo_set_wmi(struct bm1390_data *data)
> +{
> + u8 regval;
> +
> + regval = data->watermark - BM1390_WMI_MIN;
Trivial: I'd rather we didn't put stuff that clearly isn't the register
value in a variable called regval. I'd just go directly to
regval = FIELD_PREP(BM1390_MASK_FIFO_LEN,
data->watermark - BMI1390_WMI_MIN);
and avoid that first 'mis'use.
> + regval = FIELD_PREP(BM1390_MASK_FIFO_LEN, regval);
> +
> + return regmap_update_bits(data->regmap, BM1390_REG_FIFO_CTRL,
> + BM1390_MASK_FIFO_LEN, regval);
> +}
> +
> +static int bm1390_fifo_enable(struct iio_dev *idev)
> +{
> + struct bm1390_data *data = iio_priv(idev);
> + int ret;
> +
> + /* We can't do buffered stuff without IRQ as we never get WMI */
> + if (data->irq <= 0)
> + return -EINVAL;
> +
> + mutex_lock(&data->mutex);
> + if (data->trigger_enabled) {
> + ret = -EBUSY;
> + goto unlock_out;
> + }
> +
> + /* Update watermark to HW */
> + ret = bm1390_fifo_set_wmi(data);
> + if (ret)
> + goto unlock_out;
> +
> + /* Enable WMI_IRQ */
> + ret = regmap_set_bits(data->regmap, BM1390_REG_MODE_CTRL,
> + BM1390_MASK_WMI_EN);
> + if (ret)
> + goto unlock_out;
> +
> + /* Enable FIFO */
> + ret = regmap_set_bits(data->regmap, BM1390_REG_FIFO_CTRL,
> + BM1390_MASK_FIFO_EN);
> + if (ret)
> + goto unlock_out;
> +
> + data->state = BM1390_STATE_FIFO;
> +
> + data->old_timestamp = iio_get_time_ns(idev);
> + ret = bm1390_meas_set(data, BM1390_MEAS_MODE_CONTINUOUS);
> +
> +unlock_out:
> + mutex_unlock(&data->mutex);
> +
> + return ret;
> +}
> +
> +static int bm1390_fifo_disable(struct iio_dev *idev)
> +{
> + struct bm1390_data *data = iio_priv(idev);
> + int ret;
> +
> + msleep(1);
> +
> + mutex_lock(&data->mutex);
> + /* Disable FIFO */
> + ret = regmap_clear_bits(data->regmap, BM1390_REG_FIFO_CTRL,
> + BM1390_MASK_FIFO_EN);
> + if (ret)
> + goto unlock_out;
> +
> + data->state = BM1390_STATE_SAMPLE;
> +
> + /* Disable WMI_IRQ */
> + ret = regmap_clear_bits(data->regmap, BM1390_REG_MODE_CTRL,
> + BM1390_MASK_WMI_EN);
> + if (ret)
> + goto unlock_out;
> +
> + ret = bm1390_meas_set(data, BM1390_MEAS_MODE_STOP);
I'm sure it works in this order but to my mind it would make more sense
(and might still work) for fifo_disable() to be reverse of steps
in fifo_enable(). So I'd expect the mode change first.
> +
> +unlock_out:
> + mutex_unlock(&data->mutex);
> +
> + return ret;
> +}
> +static int bm1390_probe(struct i2c_client *i2c)
> +{
> + struct bm1390_data *data;
> + struct regmap *regmap;
> + struct iio_dev *idev;
> + struct device *dev;
> + unsigned int part_id;
> + int ret;
> +
> + dev = &i2c->dev;
> +
> + regmap = devm_regmap_init_i2c(i2c, &bm1390_regmap);
> + if (IS_ERR(regmap))
> + return dev_err_probe(dev, PTR_ERR(regmap),
> + "Failed to initialize Regmap\n");
> +
> + ret = devm_regulator_get_enable(dev, "vdd");
> + if (ret)
> + return dev_err_probe(dev, ret, "Failed to get regulator\n");
> +
> + ret = regmap_read(regmap, BM1390_REG_PART_ID, &part_id);
> + if (ret)
> + return dev_err_probe(dev, ret, "Failed to access sensor\n");
> +
> + if (part_id != BM1390_ID)
> + dev_warn(dev, "unknown device 0x%x\n", part_id);
> +
> + idev = devm_iio_device_alloc(dev, sizeof(*data));
> + if (!idev)
> + return -ENOMEM;
> +
> + data = iio_priv(idev);
> + data->regmap = regmap;
> + data->dev = dev;
> + data->irq = i2c->irq;
> + /*
> + * For now we just allow BM1390_WMI_MIN to BM1390_WMI_MAX and
> + * discard every other configuration when triggered mode is not used.
> + */
> + data->watermark = BM1390_WMI_MAX;
> + mutex_init(&data->mutex);
> +
> + idev->channels = bm1390_channels;
> + idev->num_channels = ARRAY_SIZE(bm1390_channels);
> + idev->name = "bm1390";
> + idev->info = &bm1390_info;
> + idev->modes = INDIO_DIRECT_MODE | INDIO_BUFFER_SOFTWARE;
Silly question that I might resolve as I read on.
If we don't have the WMI interrupt, do we have buffer_software support?
It could be made to work with a timer, but do you do so?
> +
> + ret = bm1390_chip_init(data);
> + if (ret)
> + return dev_err_probe(dev, ret, "sensor init failed\n");
> +
> + ret = bm1390_setup_buffer(data, idev);
> + if (ret)
> + return ret;
> +
> + /* No trigger if we don't have IRQ for data-ready and WMI */
> + if (i2c->irq > 0) {
> + ret = bm1390_setup_trigger(data, idev, i2c->irq);
> + if (ret)
> + return ret;
> + }
> +
> + ret = devm_iio_device_register(dev, idev);
> + if (ret < 0)
> + return dev_err_probe(dev, ret,
> + "Unable to register iio device\n");
> +
> + return 0;
> +}
