Re: [PATCH V3 4/4] arm64: dts: qcom: ipq5018: Add tsens node

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Fri, 22 Sept 2023 at 14:51, Sricharan R
<srichara@xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx> wrote:
>
> From: Sricharan Ramabadhran <quic_srichara@xxxxxxxxxxx>
>
> IPQ5018 has tsens V1.0 IP with 4 sensors.
> There is no RPM, so tsens has to be manually enabled. Adding the tsens
> and nvmem node and IPQ5018 has 4 thermal sensors (zones). With the
> critical temperature being 120'C and action is to reboot. Adding all
> the 4 zones here.
>
> Signed-off-by: Sricharan Ramabadhran <quic_srichara@xxxxxxxxxxx>
> ---
>  [v3] Ordered the qfprom device node properties as per
>       Krzysztof's comments
>
>  arch/arm64/boot/dts/qcom/ipq5018.dtsi | 169 ++++++++++++++++++++++++++
>  1 file changed, 169 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/ipq5018.dtsi b/arch/arm64/boot/dts/qcom/ipq5018.dtsi
> index 9f13d2dcdfd5..9e28b54ebcbd 100644
> --- a/arch/arm64/boot/dts/qcom/ipq5018.dtsi
> +++ b/arch/arm64/boot/dts/qcom/ipq5018.dtsi
> @@ -93,6 +93,117 @@ soc: soc@0 {
>                 #size-cells = <1>;
>                 ranges = <0 0 0 0xffffffff>;
>
> +               qfprom: qfprom@a0000 {
> +                       compatible = "qcom,ipq5018-qfprom", "qcom,qfprom";
> +                       reg = <0xa0000 0x1000>;
> +                       #address-cells = <1>;
> +                       #size-cells = <1>;
> +
> +                       tsens_base1: base1@249 {
> +                               reg = <0x249 2>;
> +                               bits = <3 8>;
> +                       };
> +
> +                       tsens_base2: base2@24a {
> +                               reg = <0x24a 2>;
> +                               bits = <3 8>;
> +                       };

Sort by the address, please, as usual.

> +
> +                       tsens_mode: mode@249 {
> +                               reg = <0x249 1>;
> +                               bits = <0 3>;
> +                       };
> +
> +                       tsens_s0_p1: s0-p1@24b {
> +                               reg = <0x24b 0x2>;
> +                               bits = <2 6>;
> +                       };
> +
> +                       tsens_s0_p2: s0-p2@24c {
> +                               reg = <0x24c 0x1>;
> +                               bits = <1 6>;
> +                       };
> +
> +                       tsens_s1_p1: s1-p1@24c {
> +                               reg = <0x24c 0x2>;
> +                               bits = <7 6>;
> +                       };
> +
> +                       tsens_s1_p2: s1-p2@24d {
> +                               reg = <0x24d 0x2>;
> +                               bits = <5 6>;
> +                       };
> +
> +                       tsens_s2_p1: s2-p1@24e {
> +                               reg = <0x24e 0x2>;
> +                               bits = <3 6>;
> +                       };
> +
> +                       tsens_s2_p2: s2-p2@24f {
> +                               reg = <0x24f 0x1>;
> +                               bits = <1 6>;
> +                       };
> +
> +                       tsens_s3_p1: s3-p1@24f {
> +                               reg = <0x24f 0x2>;
> +                               bits = <7 6>;
> +                       };
> +
> +                       tsens_s3_p2: s3-p2@250 {
> +                               reg = <0x250 0x2>;
> +                               bits = <5 6>;
> +                       };
> +
> +                       tsens_s4_p1: s4-p1@251 {
> +                               reg = <0x251 0x2>;
> +                               bits = <3 6>;
> +                       };
> +
> +                       tsens_s4_p2: s4-p2@254 {
> +                               reg = <0x254 0x1>;
> +                               bits = <0 6>;
> +                       };
> +               };
> +
> +               tsens: thermal-sensor@4a9000 {
> +                       compatible = "qcom,ipq5018-tsens";
> +                       reg = <0x4a9000 0x1000>, /* TM */
> +                             <0x4a8000 0x1000>; /* SORT */
> +
> +                       nvmem-cells = <&tsens_mode>,
> +                                     <&tsens_base1>,
> +                                     <&tsens_base2>,
> +                                     <&tsens_s0_p1>,
> +                                     <&tsens_s0_p2>,
> +                                     <&tsens_s1_p1>,
> +                                     <&tsens_s1_p2>,
> +                                     <&tsens_s2_p1>,
> +                                     <&tsens_s2_p2>,
> +                                     <&tsens_s3_p1>,
> +                                     <&tsens_s3_p2>,
> +                                     <&tsens_s4_p1>,
> +                                     <&tsens_s4_p2>;
> +
> +                       nvmem-cell-names = "mode",
> +                                          "base1",
> +                                          "base2",
> +                                          "s0_p1",
> +                                          "s0_p2",
> +                                          "s1_p1",
> +                                          "s1_p2",
> +                                          "s2_p1",
> +                                          "s2_p2",
> +                                          "s3_p1",
> +                                          "s3_p2",
> +                                          "s4_p1",
> +                                          "s4_p2";
> +
> +                       interrupts = <GIC_SPI 184 IRQ_TYPE_EDGE_RISING>;
> +                       interrupt-names = "uplow";
> +                       #qcom,sensors = <5>;
> +                       #thermal-sensor-cells = <1>;
> +               };
> +
>                 tlmm: pinctrl@1000000 {
>                         compatible = "qcom,ipq5018-tlmm";
>                         reg = <0x01000000 0x300000>;
> @@ -240,6 +351,64 @@ frame@b128000 {
>                 };
>         };
>
> +       thermal-zones {
> +               ubi32-thermal {
> +                       polling-delay-passive = <0>;
> +                       polling-delay = <0>;
> +                       thermal-sensors = <&tsens 1>;
> +
> +                       trips {
> +                               ubi32-critical {
> +                                       temperature = <120000>;
> +                                       hysteresis = <2>;
> +                                       type = "critical";
> +                               };
> +                       };
> +               };
> +
> +               cpu-thermal {

'c' < 'u'. Please sort the nodes here.

> +                       polling-delay-passive = <0>;
> +                       polling-delay = <0>;
> +                       thermal-sensors = <&tsens 2>;
> +
> +                       trips {
> +                               cpu-critical {
> +                                       temperature = <120000>;
> +                                       hysteresis = <2>;
> +                                       type = "critical";
> +                               };
> +                       };
> +               };
> +
> +               top-glue-thermal {
> +                       polling-delay-passive = <0>;
> +                       polling-delay = <0>;
> +                       thermal-sensors = <&tsens 3>;
> +
> +                       trips {
> +                               top_glue-critical {
> +                                       temperature = <120000>;
> +                                       hysteresis = <2>;
> +                                       type = "critical";
> +                               };
> +                       };
> +               };
> +
> +               gephy-thermal {
> +                       polling-delay-passive = <0>;
> +                       polling-delay = <0>;
> +                       thermal-sensors = <&tsens 4>;
> +
> +                       trips {
> +                               gephy-critical {
> +                                       temperature = <120000>;
> +                                       hysteresis = <2>;
> +                                       type = "critical";
> +                               };
> +                       };
> +               };
> +       };
> +
>         timer {
>                 compatible = "arm,armv8-timer";
>                 interrupts = <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> --
> 2.34.1
>


-- 
With best wishes
Dmitry




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux