Add StarFive JH7110 PWM controller node and add PWM pins configuration on VisionFive 2 board. Signed-off-by: William Qiu <william.qiu@xxxxxxxxxxxxxxxx> Reviewed-by: Hal Feng <hal.feng@xxxxxxxxxxxxxxxx> --- .../jh7110-starfive-visionfive-2.dtsi | 22 +++++++++++++++++++ arch/riscv/boot/dts/starfive/jh7110.dtsi | 9 ++++++++ 2 files changed, 31 insertions(+) diff --git a/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi index d79f94432b27..4bfb8f0f810f 100644 --- a/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi +++ b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi @@ -268,6 +268,12 @@ reserved-data@600000 { }; }; +&pwm { + pinctrl-names = "default"; + pinctrl-0 = <&pwm_pins>; + status = "okay"; +}; + &spi0 { pinctrl-names = "default"; pinctrl-0 = <&spi0_pins>; @@ -402,6 +408,22 @@ GPOEN_SYS_SDIO1_DATA3, }; }; + pwm_pins: pwm-0 { + pwm-pins { + pinmux = <GPIOMUX(46, GPOUT_SYS_PWM_CHANNEL0, + GPOEN_SYS_PWM0_CHANNEL0, + GPI_NONE)>, + <GPIOMUX(59, GPOUT_SYS_PWM_CHANNEL1, + GPOEN_SYS_PWM0_CHANNEL1, + GPI_NONE)>; + bias-disable; + drive-strength = <12>; + input-disable; + input-schmitt-disable; + slew-rate = <0>; + }; + }; + spi0_pins: spi0-0 { mosi-pins { pinmux = <GPIOMUX(52, GPOUT_SYS_SPI0_TXD, diff --git a/arch/riscv/boot/dts/starfive/jh7110.dtsi b/arch/riscv/boot/dts/starfive/jh7110.dtsi index e85464c328d0..c1f97c5a8ab5 100644 --- a/arch/riscv/boot/dts/starfive/jh7110.dtsi +++ b/arch/riscv/boot/dts/starfive/jh7110.dtsi @@ -736,6 +736,15 @@ spi6: spi@120a0000 { status = "disabled"; }; + pwm: pwm@120d0000 { + compatible = "starfive,jh7110-pwm"; + reg = <0x0 0x120d0000 0x0 0x10000>; + clocks = <&syscrg JH7110_SYSCLK_PWM_APB>; + resets = <&syscrg JH7110_SYSRST_PWM_APB>; + #pwm-cells = <3>; + status = "disabled"; + }; + sfctemp: temperature-sensor@120e0000 { compatible = "starfive,jh7110-temp"; reg = <0x0 0x120e0000 0x0 0x10000>; -- 2.34.1