Add device tree based drive strength configuration support. It is needed to
pass EMI validation on our hardware.
Configuration values are based on the vendor's reference driver.
Tested on KSZ9563R.
Signed-off-by: Oleksij Rempel <o.rempel@xxxxxxxxxxxxxx>
Reviewed-by: Andrew Lunn <andrew@xxxxxxx>
---
drivers/net/dsa/microchip/ksz8795_reg.h | 14 --
drivers/net/dsa/microchip/ksz9477_reg.h | 13 -
drivers/net/dsa/microchip/ksz_common.c | 309 ++++++++++++++++++++++++
drivers/net/dsa/microchip/ksz_common.h | 20 ++
4 files changed, 329 insertions(+), 27 deletions(-)
diff --git a/drivers/net/dsa/microchip/ksz8795_reg.h b/drivers/net/dsa/microchip/ksz8795_reg.h
index 7a57c6088f80..d33db4f86c64 100644
--- a/drivers/net/dsa/microchip/ksz8795_reg.h
+++ b/drivers/net/dsa/microchip/ksz8795_reg.h
@@ -442,20 +442,6 @@
#define TOS_PRIO_M KS_PRIO_M
#define TOS_PRIO_S KS_PRIO_S
-#define REG_SW_CTRL_20 0xA3
-
-#define SW_GMII_DRIVE_STRENGTH_S 4
-#define SW_DRIVE_STRENGTH_M 0x7
-#define SW_DRIVE_STRENGTH_2MA 0
-#define SW_DRIVE_STRENGTH_4MA 1
-#define SW_DRIVE_STRENGTH_8MA 2
-#define SW_DRIVE_STRENGTH_12MA 3
-#define SW_DRIVE_STRENGTH_16MA 4
-#define SW_DRIVE_STRENGTH_20MA 5
-#define SW_DRIVE_STRENGTH_24MA 6
-#define SW_DRIVE_STRENGTH_28MA 7
-#define SW_MII_DRIVE_STRENGTH_S 0
-
#define REG_SW_CTRL_21 0xA4
#define SW_IPV6_MLD_OPTION BIT(3)
diff --git a/drivers/net/dsa/microchip/ksz9477_reg.h b/drivers/net/dsa/microchip/ksz9477_reg.h
index cba3dba58bc3..504e085aab52 100644
--- a/drivers/net/dsa/microchip/ksz9477_reg.h
+++ b/drivers/net/dsa/microchip/ksz9477_reg.h
@@ -112,19 +112,6 @@
#define REG_SW_IBA_SYNC__1 0x010C
-#define REG_SW_IO_STRENGTH__1 0x010D
-#define SW_DRIVE_STRENGTH_M 0x7
-#define SW_DRIVE_STRENGTH_2MA 0
-#define SW_DRIVE_STRENGTH_4MA 1
-#define SW_DRIVE_STRENGTH_8MA 2
-#define SW_DRIVE_STRENGTH_12MA 3
-#define SW_DRIVE_STRENGTH_16MA 4
-#define SW_DRIVE_STRENGTH_20MA 5
-#define SW_DRIVE_STRENGTH_24MA 6
-#define SW_DRIVE_STRENGTH_28MA 7
-#define SW_HI_SPEED_DRIVE_STRENGTH_S 4
-#define SW_LO_SPEED_DRIVE_STRENGTH_S 0
-
#define REG_SW_IBA_STATUS__4 0x0110
#define SW_IBA_REQ BIT(31)
diff --git a/drivers/net/dsa/microchip/ksz_common.c b/drivers/net/dsa/microchip/ksz_common.c
index 42db7679c360..54048b82db71 100644
--- a/drivers/net/dsa/microchip/ksz_common.c
+++ b/drivers/net/dsa/microchip/ksz_common.c
@@ -186,6 +186,72 @@ static const struct ksz_mib_names ksz9477_mib_names[] = {
{ 0x83, "tx_discards" },
};
+struct ksz_driver_strength_prop {
+ const char *name;
+ int offset;
+ int value;
+};
+
+enum ksz_driver_strength_type {
+ KSZ_DRIVER_STRENGTH_HI,
+ KSZ_DRIVER_STRENGTH_LO,
+ KSZ_DRIVER_STRENGTH_IO,
+};
+
+/**
+ * struct ksz_drive_strength - drive strength mapping
+ * @reg_val: register value
+ * @microamp: microamp value
+ */
+struct ksz_drive_strength {
+ u32 reg_val;
+ u32 microamp;
+};
+
+/* ksz9477_drive_strengths - Drive strength mapping for KSZ9477 variants
+ *
+ * This values are not documented in KSZ9477 variants but confirmed by
+ * Microchip that KSZ9477, KSZ9567, KSZ8567, KSZ9897, KSZ9896, KSZ9563, KSZ9893
+ * and KSZ8563 are using same register (drive strength) settings like KSZ8795.
+ *
+ * Documentation in KSZ8795CLX provides more information with some
+ * recommendations:
+ * - for high speed signals
+ * 1. 4 mA or 8 mA is often used for MII, RMII, and SPI interface with using
+ * 2.5V or 3.3V VDDIO.
+ * 2. 12 mA or 16 mA is often used for MII, RMII, and SPI interface with
+ * using 1.8V VDDIO.
+ * 3. 20 mA or 24 mA is often used for GMII/RGMII interface with using 2.5V
+ * or 3.3V VDDIO.
+ * 4. 28 mA is often used for GMII/RGMII interface with using 1.8V VDDIO.
+ * 5. In same interface, the heavy loading should use higher one of the
+ * drive current strength.
+ * - for low speed signals
+ * 1. 3.3V VDDIO, use either 4 mA or 8 mA.
+ * 2. 2.5V VDDIO, use either 8 mA or 12 mA.
+ * 3. 1.8V VDDIO, use either 12 mA or 16 mA.
+ * 4. If it is heavy loading, can use higher drive current strength.
+ */
+static const struct ksz_drive_strength ksz9477_drive_strengths[] = {
+ { SW_DRIVE_STRENGTH_2MA, 2000 },
+ { SW_DRIVE_STRENGTH_4MA, 4000 },
+ { SW_DRIVE_STRENGTH_8MA, 8000 },
+ { SW_DRIVE_STRENGTH_12MA, 12000 },
+ { SW_DRIVE_STRENGTH_16MA, 16000 },
+ { SW_DRIVE_STRENGTH_20MA, 20000 },
+ { SW_DRIVE_STRENGTH_24MA, 24000 },
+ { SW_DRIVE_STRENGTH_28MA, 28000 },
+};
+
+/* ksz8830_drive_strengths - Drive strength mapping for KSZ8830, KSZ8873, ..
+ * variants.
+ * This values are documented in KSZ8873 and KSZ8863 datasheets.
+ */
+static const struct ksz_drive_strength ksz8830_drive_strengths[] = {
+ { 0, 8000 },
+ { KSZ8873_DRIVE_STRENGTH_16MA, 16000 },
+};
+
static const struct ksz_dev_ops ksz8_dev_ops = {
.setup = ksz8_setup,
.get_port_addr = ksz8_get_port_addr,
@@ -3530,6 +3596,245 @@ static void ksz_parse_rgmii_delay(struct ksz_device *dev, int port_num,
dev->ports[port_num].rgmii_tx_val = tx_delay;
}
+/**
+ * ksz_drive_strength_to_reg() - Convert drive strength value to corresponding
+ * register value.
+ * @array: The array of drive strength values to search.
+ * @array_size: The size of the array.
+ * @microamp: The drive strength value in microamp to be converted.
+ *
+ * This function searches the array of drive strength values for the given
+ * microamp value and returns the corresponding register value for that drive.
+ *
+ * Returns: If found, the corresponding register value for that drive strength
+ * is returned. Otherwise, -EINVAL is returned indicating an invalid value.
+ */
+static int ksz_drive_strength_to_reg(const struct ksz_drive_strength *array,
+ size_t array_size, int microamp)
+{
+ int i;
+
+ for (i = 0; i < array_size; i++) {
+ if (array[i].microamp == microamp)
+ return array[i].reg_val;
+ }
+
+ return -EINVAL;
+}
+
+/**
+ * ksz_drive_strength_error() - Report invalid drive strength value
+ * @dev: ksz device
+ * @array: The array of drive strength values to search.
+ * @array_size: The size of the array.
+ * @microamp: Invalid drive strength value in microamp
+ *
+ * This function logs an error message when an unsupported drive strength value
+ * is detected. It lists out all the supported drive strength values for
+ * reference in the error message.
+ */
+static void ksz_drive_strength_error(struct ksz_device *dev,
+ const struct ksz_drive_strength *array,
+ size_t array_size, int microamp)
+{
+ char supported_values[100];
+ size_t remaining_size;
+ int added_len;
+ char *ptr;
+ int i;
+
+ remaining_size = sizeof(supported_values);
+ ptr = supported_values;
+
+ for (i = 0; i < array_size; i++) {
+ added_len = snprintf(ptr, remaining_size,
+ i == 0 ? "%d" : ", %d", array[i].microamp);
+
+ if (added_len >= remaining_size)
+ break;
+
+ ptr += added_len;
+ remaining_size -= added_len;
+ }
+
+ dev_err(dev->dev, "Invalid drive strength %d, supported values are %s\n",
+ microamp, supported_values);
+}
+
+/**
+ * ksz9477_drive_strength_write() - Set the drive strength for specific KSZ9477
+ * chip variants.
+ * @dev: ksz device
+ * @props: Array of drive strength properties to be applied
+ * @num_props: Number of properties in the array
+ *
+ * This function configures the drive strength for various KSZ9477 chip variants
+ * based on the provided properties. It handles chip-specific nuances and
+ * ensures only valid drive strengths are written to the respective chip.
+ *
+ * Return: 0 on successful configuration, a negative error code on failure.
+ */
+static int ksz9477_drive_strength_write(struct ksz_device *dev,
+ struct ksz_driver_strength_prop *props,
+ int num_props)
+{
+ size_t array_size = ARRAY_SIZE(ksz9477_drive_strengths);
+ int i, ret, reg;
+ u8 mask = 0;
+ u8 val = 0;
+
+ if (props[KSZ_DRIVER_STRENGTH_IO].value != -1)
+ dev_warn(dev->dev, "%s is not supported by this chip variant\n",
+ props[KSZ_DRIVER_STRENGTH_IO].name);
+
+ if (dev->chip_id == KSZ8795_CHIP_ID ||
+ dev->chip_id == KSZ8794_CHIP_ID ||
+ dev->chip_id == KSZ8765_CHIP_ID)
+ reg = KSZ8795_REG_SW_CTRL_20;
+ else
+ reg = KSZ9477_REG_SW_IO_STRENGTH;
+
+ for (i = 0; i < num_props; i++) {
+ if (props[i].value == -1)
+ continue;
+
+ ret = ksz_drive_strength_to_reg(ksz9477_drive_strengths,
+ array_size, props[i].value);
+ if (ret < 0) {
+ ksz_drive_strength_error(dev, ksz9477_drive_strengths,
+ array_size, props[i].value);
+ return ret;
+ }
+
+ mask |= SW_DRIVE_STRENGTH_M << props[i].offset;
+ val |= ret << props[i].offset;
+ }
+
+ return ksz_rmw8(dev, reg, mask, val);
+}
+
+/**
+ * ksz8830_drive_strength_write() - Set the drive strength configuration for
+ * KSZ8830 compatible chip variants.
+ * @dev: ksz device
+ * @props: Array of drive strength properties to be set
+ * @num_props: Number of properties in the array
+ *
+ * This function applies the specified drive strength settings to KSZ8830 chip
+ * variants (KSZ8873, KSZ8863).
+ * It ensures the configurations align with what the chip variant supports and
+ * warns or errors out on unsupported settings.
+ *
+ * Return: 0 on success, error code otherwise
+ */
+static int ksz8830_drive_strength_write(struct ksz_device *dev,
+ struct ksz_driver_strength_prop *props,
+ int num_props)
+{
+ size_t array_size = ARRAY_SIZE(ksz8830_drive_strengths);
+ int microamp;
+ int i, ret;
+
+ for (i = 0; i < num_props; i++) {
+ if (props[i].value == -1 || i == KSZ_DRIVER_STRENGTH_IO)
+ continue;
+
+ dev_warn(dev->dev, "%s is not supported by this chip variant\n",
+ props[i].name);
+ }
+
+ microamp = props[KSZ_DRIVER_STRENGTH_IO].value;
+ ret = ksz_drive_strength_to_reg(ksz8830_drive_strengths, array_size,
+ microamp);
+ if (ret < 0) {
+ ksz_drive_strength_error(dev, ksz8830_drive_strengths,
+ array_size, microamp);
+ return ret;
+ }
+
+ return ksz_rmw8(dev, KSZ8873_REG_GLOBAL_CTRL_12,
+ KSZ8873_DRIVE_STRENGTH_16MA, ret);
+}
+
+/**
+ * ksz_parse_drive_strength() - Extract and apply drive strength configurations
+ * from device tree properties.
+ * @dev: ksz device
+ *
+ * This function reads the specified drive strength properties from the
+ * device tree, validates against the supported chip variants, and sets
+ * them accordingly. An error should be critical here, as the drive strength
+ * settings are crucial for EMI compliance.
+ *
+ * Return: 0 on success, error code otherwise
+ */
+static int ksz_parse_drive_strength(struct ksz_device *dev)
+{
+ struct ksz_driver_strength_prop of_props[] = {
+ [KSZ_DRIVER_STRENGTH_HI] = {
+ .name = "microchip,hi-drive-strength-microamp",
+ .offset = SW_HI_SPEED_DRIVE_STRENGTH_S,
+ .value = -1,
+ },
+ [KSZ_DRIVER_STRENGTH_LO] = {
+ .name = "microchip,lo-drive-strength-microamp",
+ .offset = SW_LO_SPEED_DRIVE_STRENGTH_S,
+ .value = -1,
+ },
+ [KSZ_DRIVER_STRENGTH_IO] = {
+ .name = "microchip,io-drive-strength-microamp",
+ .offset = 0, /* don't care */
+ .value = -1,
+ },
+ };
+ struct device_node *np = dev->dev->of_node;
+ bool have_any_prop = false;
+ int i, ret;
+
+ for (i = 0; i < ARRAY_SIZE(of_props); i++) {
+ ret = of_property_read_u32(np, of_props[i].name,
+ &of_props[i].value);
+ if (ret && ret != -EINVAL)
+ dev_warn(dev->dev, "Failed to read %s\n",
+ of_props[i].name);
+ if (ret)
+ continue;
+
+ have_any_prop = true;
+ }
+
+ if (!have_any_prop)
+ return 0;
+
+ switch (dev->chip_id) {
+ case KSZ8830_CHIP_ID:
+ return ksz8830_drive_strength_write(dev, of_props,
+ ARRAY_SIZE(of_props));
+ case KSZ8795_CHIP_ID:
+ case KSZ8794_CHIP_ID:
+ case KSZ8765_CHIP_ID:
+ case KSZ8563_CHIP_ID:
+ case KSZ9477_CHIP_ID:
+ case KSZ9563_CHIP_ID:
+ case KSZ9567_CHIP_ID:
+ case KSZ9893_CHIP_ID:
+ case KSZ9896_CHIP_ID:
+ case KSZ9897_CHIP_ID:
+ return ksz9477_drive_strength_write(dev, of_props,
+ ARRAY_SIZE(of_props));
+ default:
+ for (i = 0; i < ARRAY_SIZE(of_props); i++) {
+ if (of_props[i].value == -1)
+ continue;
+
+ dev_warn(dev->dev, "%s is not supported by this chip variant\n",
+ of_props[i].name);
+ }
+ }
+
+ return 0;
+}
+
int ksz_switch_register(struct ksz_device *dev)
{
const struct ksz_chip_data *info;
@@ -3612,6 +3917,10 @@ int ksz_switch_register(struct ksz_device *dev)
for (port_num = 0; port_num < dev->info->port_cnt; ++port_num)
dev->ports[port_num].interface = PHY_INTERFACE_MODE_NA;
if (dev->dev->of_node) {
+ ret = ksz_parse_drive_strength(dev);
+ if (ret)
+ return ret;
+
ret = of_get_phy_mode(dev->dev->of_node, &interface);
if (ret == 0)
dev->compat_interface = interface;
diff --git a/drivers/net/dsa/microchip/ksz_common.h b/drivers/net/dsa/microchip/ksz_common.h
index a4de58847dea..ca37b5b87946 100644
--- a/drivers/net/dsa/microchip/ksz_common.h
+++ b/drivers/net/dsa/microchip/ksz_common.h
@@ -689,6 +689,26 @@ static inline int is_lan937x(struct ksz_device *dev)
#define KSZ8_LEGAL_PACKET_SIZE 1518
#define KSZ9477_MAX_FRAME_SIZE 9000
+#define KSZ8873_REG_GLOBAL_CTRL_12 0x0e
+/* Drive Strength of I/O Pad
+ * 0: 8mA, 1: 16mA
+ */
+#define KSZ8873_DRIVE_STRENGTH_16MA BIT(6)
+
+#define KSZ8795_REG_SW_CTRL_20 0xa3
+#define KSZ9477_REG_SW_IO_STRENGTH 0x010d
+#define SW_DRIVE_STRENGTH_M 0x7
+#define SW_DRIVE_STRENGTH_2MA 0
+#define SW_DRIVE_STRENGTH_4MA 1
+#define SW_DRIVE_STRENGTH_8MA 2
+#define SW_DRIVE_STRENGTH_12MA 3
+#define SW_DRIVE_STRENGTH_16MA 4
+#define SW_DRIVE_STRENGTH_20MA 5
+#define SW_DRIVE_STRENGTH_24MA 6
+#define SW_DRIVE_STRENGTH_28MA 7
+#define SW_HI_SPEED_DRIVE_STRENGTH_S 4
+#define SW_LO_SPEED_DRIVE_STRENGTH_S 0
+
#define KSZ9477_REG_PORT_OUT_RATE_0 0x0420
#define KSZ9477_OUT_RATE_NO_LIMIT 0
--
2.39.2
