Add basic device-tree for the Genio 700 EVK board. The Genio 700 EVK is based on MediaTek MT8390 SoC. MT8390 hardware register maps are identical to MT8188. The Genio 700 EVK has following features: - MT8390 SoC - MT6365 PMIC - MT6319 Buck IC - 12V DC Jack - 2x4GB LPDDR4X - 64GB eMMC 5.1 - 64Mb SPI NOR - M.2 Key A-E slot with PCIe Gen2 and USB 2.0 - 2x DSI LCM ports - 2x touch sensor ports - 2x MIPI-CSI, as camera daughter board slots - USB 2 micro USB connector - USB 3 with 1 to 2 hub: - M.2 Key B slot - Type-C connector, with DisplayPort over Type-C - HDMI 2.0 TX port with Type A HDMI connector - eDP port - Gigabit Ethernet with RJ45 connector - SD card slot - Earphone Jack - Analog Microphone - 2x Digital Microphone - 3x UART with serial-to-usb converters and micro USB connectors Signed-off-by: Chris-QJ Chen <chris-qj.chen@xxxxxxxxxxxx> Signed-off-by: Pablo Sun <pablo.sun@xxxxxxxxxxxx> Signed-off-by: Macpaul Lin <macpaul.lin@xxxxxxxxxxxx> --- arch/arm64/boot/dts/mediatek/Makefile | 1 + .../dts/mediatek/mt8390-genio-700-evk.dts | 880 ++++++++++++++++++ 2 files changed, 881 insertions(+) create mode 100644 arch/arm64/boot/dts/mediatek/mt8390-genio-700-evk.dts dependencies for v1: - This patch should be applied after the following patch set - mt8365-gneio-350-evk's dts change (v4) - https://lore.kernel.org/linux-arm-kernel/20230912092444.31635-1-macpaul.lin@xxxxxxxxxxxx/T/ - mt8395-genio-1200-evk's dts basic support (v6) - https://lore.kernel.org/lkml/20230911115717.26184-1-macpaul.lin@xxxxxxxxxxxx/T/ - mt8188 platform's basic support - https://lore.kernel.org/lkml/a4e1a80ebd19896410f50b0297e05dce06fb47cc.camel@xxxxxxxxxxxx/T/ changes for v2: - Fix gpio defines '0' to 'GPIO_ACTIVE_HIGH'. - Drop duplicate name: 'default' for I2C4. - Update dependencies - mt8365-gneio-350-evk's dts change (v5) - https://lore.kernel.org/lkml/20230913032226.4092-1-macpaul.lin@xxxxxxxxxxxx/ - mt8395-genio-1200-evk's dts basic support (v7) - https://lore.kernel.org/linux-arm-kernel/20230913032057.3197-1-macpaul.lin@xxxxxxxxxxxx/T/ - mt8188 platform's basic support (v4) - https://lore.kernel.org/lkml/a4e1a80ebd19896410f50b0297e05dce06fb47cc.camel@xxxxxxxxxxxx/T/ changes for v3: - No change. - Update dependencies - mt8365-gneio-350-evk's dts change (v5) - https://lore.kernel.org/lkml/20230913032226.4092-1-macpaul.lin@xxxxxxxxxxxx/ - mt8395-genio-1200-evk's dts basic support (v8) - https://lore.kernel.org/lkml/20230914055145.16801-1-macpaul.lin@xxxxxxxxxxxx/T/ - mt8188 platform's basic support (v4) - https://lore.kernel.org/lkml/a4e1a80ebd19896410f50b0297e05dce06fb47cc.camel@xxxxxxxxxxxx/T/ diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile index 22f362bbbdac..3262849c0f6b 100644 --- a/arch/arm64/boot/dts/mediatek/Makefile +++ b/arch/arm64/boot/dts/mediatek/Makefile @@ -54,5 +54,6 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-cherry-tomato-r3.dtb dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-demo.dtb dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-evb.dtb dtb-$(CONFIG_ARCH_MEDIATEK) += mt8365-genio-350-evk.dtb +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8390-genio-700-evk.dtb dtb-$(CONFIG_ARCH_MEDIATEK) += mt8395-genio-1200-evk.dtb dtb-$(CONFIG_ARCH_MEDIATEK) += mt8516-pumpkin.dtb diff --git a/arch/arm64/boot/dts/mediatek/mt8390-genio-700-evk.dts b/arch/arm64/boot/dts/mediatek/mt8390-genio-700-evk.dts new file mode 100644 index 000000000000..ed6bbf0c15cc --- /dev/null +++ b/arch/arm64/boot/dts/mediatek/mt8390-genio-700-evk.dts @@ -0,0 +1,880 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) +/* + * Copyright (C) 2023 MediaTek Inc. + * Author: Chris Chen <chris-qj.chen@xxxxxxxxxxxx> + * Pablo Sun <pablo.sun@xxxxxxxxxxxx> + * Macpaul Lin <macpaul.lin@xxxxxxxxxxxx> + */ +/dts-v1/; + +#include "mt8188.dtsi" +#include "mt6359.dtsi" +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/pinctrl/mediatek,mt8188-pinfunc.h> +#include <dt-bindings/regulator/mediatek,mt6360-regulator.h> +#include <dt-bindings/spmi/spmi.h> +#include <dt-bindings/usb/pd.h> + +/ { + model = "MediaTek Genio-700 EVK"; + compatible = "mediatek,mt8390-evk", "mediatek,mt8390", + "mediatek,mt8188"; + + aliases { + serial0 = &uart0; + }; + + chosen { + stdout-path = "serial0:921600n8"; + }; + + firmware { + optee { + compatible = "linaro,optee-tz"; + method = "smc"; + }; + }; + + memory@40000000 { + device_type = "memory"; + reg = <0 0x40000000 0x2 0x00000000>; + }; + + reserved-memory { + #address-cells = <2>; + #size-cells = <2>; + ranges; + + /* + * 12 MiB reserved for OP-TEE (BL32) + * +-----------------------+ 0x43e0_0000 + * | SHMEM 2MiB | + * +-----------------------+ 0x43c0_0000 + * | | TA_RAM 8MiB | + * + TZDRAM +--------------+ 0x4340_0000 + * | | TEE_RAM 2MiB | + * +-----------------------+ 0x4320_0000 + */ + optee_reserved: optee@43200000 { + no-map; + reg = <0 0x43200000 0 0x00c00000>; + }; + + scp_mem: memory@50000000 { + compatible = "shared-dma-pool"; + reg = <0 0x50000000 0 0x2900000>; + no-map; + }; + + /* 2 MiB reserved for ARM Trusted Firmware (BL31) */ + bl31_secmon_reserved: memory@54600000 { + no-map; + reg = <0 0x54600000 0x0 0x200000>; + }; + + apu_mem: memory@55000000 { + compatible = "shared-dma-pool"; + reg = <0 0x55000000 0 0x1400000>; /* 20 MB */ + }; + + vpu_mem: memory@57000000 { + compatible = "shared-dma-pool"; + reg = <0 0x57000000 0 0x1400000>; /* 20 MB */ + }; + }; + + common_fixed_5v: regulator-0 { + compatible = "regulator-fixed"; + regulator-name = "5v_en"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&pio 10 GPIO_ACTIVE_HIGH>; + enable-active-high; + regulator-always-on; + }; + + edp_panel_fixed_3v3: regulator-1 { + compatible = "regulator-fixed"; + regulator-name = "edp_panel_3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + enable-active-high; + gpio = <&pio 15 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&edp_panel_3v3_en_pins>; + }; + + gpio_fixed_3v3: regulator-2 { + compatible = "regulator-fixed"; + regulator-name = "gpio_3v3_en"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&pio 9 GPIO_ACTIVE_HIGH>; + enable-active-high; + regulator-always-on; + }; + + sdio_fixed_1v8: regulator-3 { + compatible = "regulator-fixed"; + regulator-name = "sdio_io"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + enable-active-high; + regulator-always-on; + }; + + sdio_fixed_3v3: regulator-4 { + compatible = "regulator-fixed"; + regulator-name = "sdio_card"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&pio 74 GPIO_ACTIVE_HIGH>; + enable-active-high; + regulator-always-on; + }; + + touch0_fixed_3v3: regulator-5 { + compatible = "regulator-fixed"; + regulator-name = "touch_3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&pio 119 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + usb_hub_fixed_3v3: regulator-6 { + compatible = "regulator-fixed"; + regulator-name = "usb_hub_3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&pio 112 GPIO_ACTIVE_HIGH>; /* HUB_3V3_EN */ + startup-delay-us = <10000>; + enable-active-high; + }; + + usb_hub_reset_1v8: regulator-7 { + compatible = "regulator-fixed"; + regulator-name = "usb_hub_reset"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + gpio = <&pio 7 GPIO_ACTIVE_HIGH>; /* HUB_RESET */ + vin-supply = <&usb_hub_fixed_3v3>; + }; + + usb_p0_vbus: regulator-8 { + compatible = "regulator-fixed"; + regulator-name = "usb_p0_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&pio 84 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + usb_p1_vbus: regulator-9 { + compatible = "regulator-fixed"; + regulator-name = "usb_p1_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&pio 87 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + usb_p2_vbus: regulator-10 { + compatible = "regulator-fixed"; + regulator-name = "usb_p2_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + }; +}; + +&i2c0 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins>; + clock-frequency = <400000>; + status = "okay"; + + touchscreen@5d { + compatible = "goodix,gt9271"; + reg = <0x5d>; + interrupt-parent = <&pio>; + interrupts = <6 IRQ_TYPE_EDGE_RISING>; + irq-gpios = <&pio 6 GPIO_ACTIVE_HIGH>; + reset-gpios = <&pio 5 GPIO_ACTIVE_HIGH>; + AVDD28-supply = <&touch0_fixed_3v3>; + VDDIO-supply = <&mt6359_vio18_ldo_reg>; + pinctrl-names = "default"; + pinctrl-0 = <&touch_pins>; + }; +}; + +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins>; + clock-frequency = <400000>; + status = "okay"; +}; + +&i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pins>; + clock-frequency = <400000>; + status = "okay"; +}; + +&i2c3 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c3_pins>; + clock-frequency = <400000>; + status = "okay"; +}; + +&i2c4 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c4_pins>; + pinctrl-1 = <&rt1715_int_pins>; + clock-frequency = <1000000>; + status = "okay"; +}; + +&i2c5 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c5_pins>; + clock-frequency = <400000>; + status = "okay"; +}; + +&i2c6 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c6_pins>; + clock-frequency = <400000>; + status = "okay"; +}; + +&mmc0 { + status = "okay"; + pinctrl-names = "default", "state_uhs"; + pinctrl-0 = <&mmc0_default_pins>; + pinctrl-1 = <&mmc0_uhs_pins>; + bus-width = <8>; + max-frequency = <200000000>; + cap-mmc-highspeed; + mmc-hs200-1_8v; + mmc-hs400-1_8v; + supports-cqe; + cap-mmc-hw-reset; + no-sdio; + no-sd; + hs400-ds-delay = <0x1481b>; + vmmc-supply = <&mt6359_vemc_1_ldo_reg>; + vqmmc-supply = <&mt6359_vufs_ldo_reg>; + non-removable; +}; + +&mmc1 { + status = "okay"; + pinctrl-names = "default", "state_uhs"; + pinctrl-0 = <&mmc1_default_pins>; + pinctrl-1 = <&mmc1_uhs_pins>; + bus-width = <4>; + max-frequency = <200000000>; + cap-sd-highspeed; + sd-uhs-sdr50; + sd-uhs-sdr104; + no-mmc; + no-sdio; + cd-gpios = <&pio 2 GPIO_ACTIVE_LOW>; + vmmc-supply = <&mt6359_vpa_buck_reg>; + vqmmc-supply = <&mt6359_vsim1_ldo_reg>; +}; + +&mt6359_vbbck_ldo_reg { + regulator-always-on; +}; + +&mt6359_vcn18_ldo_reg { + regulator-always-on; +}; + +&mt6359_vcn33_2_bt_ldo_reg { + regulator-always-on; +}; + +&mt6359_vcore_buck_reg { + regulator-always-on; +}; + +&mt6359_vgpu11_buck_reg { + regulator-always-on; +}; + +&mt6359_vpa_buck_reg { + regulator-max-microvolt = <3100000>; +}; + +&mt6359_vpu_buck_reg { + regulator-always-on; +}; + +&mt6359_vrf12_ldo_reg { + regulator-always-on; +}; + +&mt6359_vsim1_ldo_reg { + regulator-enable-ramp-delay = <480>; +}; + +&mt6359_vufs_ldo_reg { + regulator-always-on; +}; + +&mt6359codec { + mediatek,mic-type-0 = <1>; /* ACC */ + mediatek,mic-type-1 = <3>; /* DCC */ +}; + +&pio { + audio_default_pins: audio-default-pins { + pins-cmd-dat { + pinmux = <PINMUX_GPIO101__FUNC_O_AUD_CLK_MOSI>, + <PINMUX_GPIO102__FUNC_O_AUD_SYNC_MOSI>, + <PINMUX_GPIO103__FUNC_O_AUD_DAT_MOSI0>, + <PINMUX_GPIO104__FUNC_O_AUD_DAT_MOSI1>, + <PINMUX_GPIO105__FUNC_I0_AUD_DAT_MISO0>, + <PINMUX_GPIO106__FUNC_I0_AUD_DAT_MISO1>, + <PINMUX_GPIO107__FUNC_B0_I2SIN_MCK>, + <PINMUX_GPIO108__FUNC_B0_I2SIN_BCK>, + <PINMUX_GPIO109__FUNC_B0_I2SIN_WS>, + <PINMUX_GPIO110__FUNC_I0_I2SIN_D0>, + <PINMUX_GPIO114__FUNC_O_I2SO2_MCK>, + <PINMUX_GPIO115__FUNC_B0_I2SO2_BCK>, + <PINMUX_GPIO116__FUNC_B0_I2SO2_WS>, + <PINMUX_GPIO117__FUNC_O_I2SO2_D0>, + <PINMUX_GPIO118__FUNC_O_I2SO2_D1>, + <PINMUX_GPIO121__FUNC_B0_PCM_CLK>, + <PINMUX_GPIO122__FUNC_B0_PCM_SYNC>, + <PINMUX_GPIO124__FUNC_I0_PCM_DI>, + <PINMUX_GPIO125__FUNC_O_DMIC1_CLK>, + <PINMUX_GPIO126__FUNC_I0_DMIC1_DAT>, + <PINMUX_GPIO128__FUNC_O_DMIC2_CLK>, + <PINMUX_GPIO129__FUNC_I0_DMIC2_DAT>; + }; + }; + + dptx_pins: dptx-pins { + pins-cmd-dat { + pinmux = <PINMUX_GPIO46__FUNC_I0_DP_TX_HPD>; + bias-pull-up; + }; + }; + + edp_panel_3v3_en_pins: edp-panel-3v3-en-pins { + pins1 { + pinmux = <PINMUX_GPIO15__FUNC_B_GPIO15>; + output-high; + }; + }; + + eth_default_pins: eth-default-pins { + pins-cc { + pinmux = <PINMUX_GPIO139__FUNC_B0_GBE_TXC>, + <PINMUX_GPIO140__FUNC_I0_GBE_RXC>, + <PINMUX_GPIO141__FUNC_I0_GBE_RXDV>, + <PINMUX_GPIO142__FUNC_O_GBE_TXEN>; + drive-strength = <MTK_DRIVE_8mA>; + }; + + pins-mdio { + pinmux = <PINMUX_GPIO143__FUNC_O_GBE_MDC>, + <PINMUX_GPIO144__FUNC_B1_GBE_MDIO>; + drive-strength = <MTK_DRIVE_8mA>; + input-enable; + }; + + pins-power { + pinmux = <PINMUX_GPIO145__FUNC_B_GPIO145>, + <PINMUX_GPIO146__FUNC_B_GPIO146>; + output-high; + }; + + pins-rxd { + pinmux = <PINMUX_GPIO135__FUNC_I0_GBE_RXD3>, + <PINMUX_GPIO136__FUNC_I0_GBE_RXD2>, + <PINMUX_GPIO137__FUNC_I0_GBE_RXD1>, + <PINMUX_GPIO138__FUNC_I0_GBE_RXD0>; + drive-strength = <MTK_DRIVE_8mA>; + }; + + pins-txd { + pinmux = <PINMUX_GPIO131__FUNC_O_GBE_TXD3>, + <PINMUX_GPIO132__FUNC_O_GBE_TXD2>, + <PINMUX_GPIO133__FUNC_O_GBE_TXD1>, + <PINMUX_GPIO134__FUNC_O_GBE_TXD0>; + drive-strength = <MTK_DRIVE_8mA>; + }; + }; + + eth_sleep_pins: eth-sleep-pins { + pins-cc { + pinmux = <PINMUX_GPIO139__FUNC_B_GPIO139>, + <PINMUX_GPIO140__FUNC_B_GPIO140>, + <PINMUX_GPIO141__FUNC_B_GPIO141>, + <PINMUX_GPIO142__FUNC_B_GPIO142>; + }; + + pins-mdio { + pinmux = <PINMUX_GPIO143__FUNC_B_GPIO143>, + <PINMUX_GPIO144__FUNC_B_GPIO144>; + input-disable; + bias-disable; + }; + + pins-rxd { + pinmux = <PINMUX_GPIO135__FUNC_B_GPIO135>, + <PINMUX_GPIO136__FUNC_B_GPIO136>, + <PINMUX_GPIO137__FUNC_B_GPIO137>, + <PINMUX_GPIO138__FUNC_B_GPIO138>; + }; + + pins-txd { + pinmux = <PINMUX_GPIO131__FUNC_B_GPIO131>, + <PINMUX_GPIO132__FUNC_B_GPIO132>, + <PINMUX_GPIO133__FUNC_B_GPIO133>, + <PINMUX_GPIO134__FUNC_B_GPIO134>; + }; + }; + + i2c0_pins: i2c0-pins { + pins { + pinmux = <PINMUX_GPIO56__FUNC_B1_SDA0>, + <PINMUX_GPIO55__FUNC_B1_SCL0>; + bias-pull-up = <MTK_PULL_SET_RSEL_011>; + drive-strength-microamp = <1000>; + }; + }; + + i2c1_pins: i2c1-pins { + pins { + pinmux = <PINMUX_GPIO58__FUNC_B1_SDA1>, + <PINMUX_GPIO57__FUNC_B1_SCL1>; + bias-pull-up = <MTK_PULL_SET_RSEL_011>; + drive-strength-microamp = <1000>; + }; + }; + + i2c2_pins: i2c2-pins { + pins { + pinmux = <PINMUX_GPIO60__FUNC_B1_SDA2>, + <PINMUX_GPIO59__FUNC_B1_SCL2>; + bias-pull-up = <MTK_PULL_SET_RSEL_011>; + drive-strength-microamp = <1000>; + }; + }; + + i2c3_pins: i2c3-pins { + pins { + pinmux = <PINMUX_GPIO62__FUNC_B1_SDA3>, + <PINMUX_GPIO61__FUNC_B1_SCL3>; + bias-pull-up = <MTK_PULL_SET_RSEL_011>; + drive-strength-microamp = <1000>; + }; + }; + + i2c4_pins: i2c4-pins { + pins { + pinmux = <PINMUX_GPIO64__FUNC_B1_SDA4>, + <PINMUX_GPIO63__FUNC_B1_SCL4>; + bias-pull-up = <MTK_PULL_SET_RSEL_011>; + drive-strength-microamp = <1000>; + }; + }; + + i2c5_pins: i2c5-pins { + pins { + pinmux = <PINMUX_GPIO66__FUNC_B1_SDA5>, + <PINMUX_GPIO65__FUNC_B1_SCL5>; + bias-pull-up = <MTK_PULL_SET_RSEL_011>; + drive-strength-microamp = <1000>; + }; + }; + + i2c6_pins: i2c6-pins { + pins { + pinmux = <PINMUX_GPIO68__FUNC_B1_SDA6>, + <PINMUX_GPIO67__FUNC_B1_SCL6>; + bias-pull-up = <MTK_PULL_SET_RSEL_011>; + drive-strength-microamp = <1000>; + }; + }; + + gpio_key_pins: gpio-key-pins { + pins { + pinmux = <PINMUX_GPIO42__FUNC_B1_KPCOL0>, + <PINMUX_GPIO43__FUNC_B1_KPCOL1>, + <PINMUX_GPIO44__FUNC_B1_KPROW0>; + }; + }; + + mmc0_default_pins: mmc0-default-pins { + pins-clk { + pinmux = <PINMUX_GPIO157__FUNC_B1_MSDC0_CLK>; + drive-strength = <MTK_DRIVE_6mA>; + bias-pull-down = <MTK_PUPD_SET_R1R0_10>; + }; + + pins-cmd-dat { + pinmux = <PINMUX_GPIO161__FUNC_B1_MSDC0_DAT0>, + <PINMUX_GPIO160__FUNC_B1_MSDC0_DAT1>, + <PINMUX_GPIO159__FUNC_B1_MSDC0_DAT2>, + <PINMUX_GPIO158__FUNC_B1_MSDC0_DAT3>, + <PINMUX_GPIO154__FUNC_B1_MSDC0_DAT4>, + <PINMUX_GPIO153__FUNC_B1_MSDC0_DAT5>, + <PINMUX_GPIO152__FUNC_B1_MSDC0_DAT6>, + <PINMUX_GPIO151__FUNC_B1_MSDC0_DAT7>, + <PINMUX_GPIO156__FUNC_B1_MSDC0_CMD>; + input-enable; + drive-strength = <MTK_DRIVE_6mA>; + bias-pull-up = <MTK_PUPD_SET_R1R0_01>; + }; + + pins-rst { + pinmux = <PINMUX_GPIO155__FUNC_O_MSDC0_RSTB>; + drive-strength = <MTK_DRIVE_6mA>; + bias-pull-up = <MTK_PUPD_SET_R1R0_01>; + }; + }; + + mmc0_uhs_pins: mmc0-uhs-pins { + pins-clk { + pinmux = <PINMUX_GPIO157__FUNC_B1_MSDC0_CLK>; + drive-strength = <MTK_DRIVE_8mA>; + bias-pull-down = <MTK_PUPD_SET_R1R0_10>; + }; + + pins-cmd-dat { + pinmux = <PINMUX_GPIO161__FUNC_B1_MSDC0_DAT0>, + <PINMUX_GPIO160__FUNC_B1_MSDC0_DAT1>, + <PINMUX_GPIO159__FUNC_B1_MSDC0_DAT2>, + <PINMUX_GPIO158__FUNC_B1_MSDC0_DAT3>, + <PINMUX_GPIO154__FUNC_B1_MSDC0_DAT4>, + <PINMUX_GPIO153__FUNC_B1_MSDC0_DAT5>, + <PINMUX_GPIO152__FUNC_B1_MSDC0_DAT6>, + <PINMUX_GPIO151__FUNC_B1_MSDC0_DAT7>, + <PINMUX_GPIO156__FUNC_B1_MSDC0_CMD>; + input-enable; + drive-strength = <MTK_DRIVE_8mA>; + bias-pull-up = <MTK_PUPD_SET_R1R0_01>; + }; + + pins-ds { + pinmux = <PINMUX_GPIO162__FUNC_B0_MSDC0_DSL>; + drive-strength = <MTK_DRIVE_8mA>; + bias-pull-down = <MTK_PUPD_SET_R1R0_10>; + }; + + pins-rst { + pinmux = <PINMUX_GPIO155__FUNC_O_MSDC0_RSTB>; + drive-strength = <MTK_DRIVE_8mA>; + bias-pull-up = <MTK_PUPD_SET_R1R0_01>; + }; + }; + + mmc1_default_pins: mmc1-default-pins { + pins-clk { + pinmux = <PINMUX_GPIO164__FUNC_B1_MSDC1_CLK>; + drive-strength = <MTK_DRIVE_6mA>; + bias-pull-down = <MTK_PUPD_SET_R1R0_10>; + }; + + pins-cmd-dat { + pinmux = <PINMUX_GPIO163__FUNC_B1_MSDC1_CMD>, + <PINMUX_GPIO165__FUNC_B1_MSDC1_DAT0>, + <PINMUX_GPIO166__FUNC_B1_MSDC1_DAT1>, + <PINMUX_GPIO167__FUNC_B1_MSDC1_DAT2>, + <PINMUX_GPIO168__FUNC_B1_MSDC1_DAT3>; + input-enable; + drive-strength = <MTK_DRIVE_6mA>; + bias-pull-up = <MTK_PUPD_SET_R1R0_01>; + }; + + pins-insert { + pinmux = <PINMUX_GPIO2__FUNC_B_GPIO2>; + bias-pull-up; + }; + }; + + mmc1_uhs_pins: mmc1-uhs-pins { + pins-clk { + pinmux = <PINMUX_GPIO164__FUNC_B1_MSDC1_CLK>; + drive-strength = <MTK_DRIVE_6mA>; + bias-pull-down = <MTK_PUPD_SET_R1R0_10>; + }; + + pins-cmd-dat { + pinmux = <PINMUX_GPIO163__FUNC_B1_MSDC1_CMD>, + <PINMUX_GPIO165__FUNC_B1_MSDC1_DAT0>, + <PINMUX_GPIO166__FUNC_B1_MSDC1_DAT1>, + <PINMUX_GPIO167__FUNC_B1_MSDC1_DAT2>, + <PINMUX_GPIO168__FUNC_B1_MSDC1_DAT3>; + input-enable; + drive-strength = <MTK_DRIVE_6mA>; + bias-pull-up = <MTK_PUPD_SET_R1R0_01>; + }; + }; + + mmc2_default_pins: mmc2-default-pins { + pins-clk { + pinmux = <PINMUX_GPIO170__FUNC_B1_MSDC2_CLK>; + drive-strength = <MTK_DRIVE_4mA>; + bias-pull-down = <MTK_PUPD_SET_R1R0_10>; + }; + + pins-cmd-dat { + pinmux = <PINMUX_GPIO169__FUNC_B1_MSDC2_CMD>, + <PINMUX_GPIO171__FUNC_B1_MSDC2_DAT0>, + <PINMUX_GPIO172__FUNC_B1_MSDC2_DAT1>, + <PINMUX_GPIO173__FUNC_B1_MSDC2_DAT2>, + <PINMUX_GPIO174__FUNC_B1_MSDC2_DAT3>; + input-enable; + drive-strength = <MTK_DRIVE_6mA>; + bias-pull-up = <MTK_PUPD_SET_R1R0_01>; + }; + + pins-pcm { + pinmux = <PINMUX_GPIO123__FUNC_O_PCM_DO>; + }; + }; + + mmc2_uhs_pins: mmc2-uhs-pins { + pins-clk { + pinmux = <PINMUX_GPIO170__FUNC_B1_MSDC2_CLK>; + drive-strength = <MTK_DRIVE_4mA>; + bias-pull-down = <MTK_PUPD_SET_R1R0_10>; + }; + + pins-cmd-dat { + pinmux = <PINMUX_GPIO169__FUNC_B1_MSDC2_CMD>, + <PINMUX_GPIO171__FUNC_B1_MSDC2_DAT0>, + <PINMUX_GPIO172__FUNC_B1_MSDC2_DAT1>, + <PINMUX_GPIO173__FUNC_B1_MSDC2_DAT2>, + <PINMUX_GPIO174__FUNC_B1_MSDC2_DAT3>; + input-enable; + drive-strength = <MTK_DRIVE_6mA>; + bias-pull-up = <MTK_PUPD_SET_R1R0_01>; + }; + }; + + mmc2_eint_pins: mmc2-eint-pins { + pins-dat1 { + pinmux = <PINMUX_GPIO172__FUNC_B_GPIO172>; + input-enable; + bias-pull-up = <MTK_PUPD_SET_R1R0_01>; + }; + }; + + mmc2_dat1_pins: mmc2-dat1-pins { + pins-dat1 { + pinmux = <PINMUX_GPIO172__FUNC_B1_MSDC2_DAT1>; + input-enable; + drive-strength = <MTK_DRIVE_6mA>; + bias-pull-up = <MTK_PUPD_SET_R1R0_01>; + }; + }; + + panel_default_pins: panel-default-pins { + pins-dcdc { + pinmux = <PINMUX_GPIO45__FUNC_B_GPIO45>; + output-low; + }; + + pins-en { + pinmux = <PINMUX_GPIO111__FUNC_B_GPIO111>; + output-low; + }; + + pins-rst { + pinmux = <PINMUX_GPIO25__FUNC_B_GPIO25>; + output-high; + }; + }; + + rt1715_int_pins: rt1715-int-pins { + pins_cmd0_dat { + pinmux = <PINMUX_GPIO12__FUNC_B_GPIO12>; + bias-pull-up; + input-enable; + }; + }; + + spi0_pins: spi0-pins { + pins-spi { + pinmux = <PINMUX_GPIO69__FUNC_O_SPIM0_CSB>, + <PINMUX_GPIO70__FUNC_O_SPIM0_CLK>, + <PINMUX_GPIO71__FUNC_B0_SPIM0_MOSI>, + <PINMUX_GPIO72__FUNC_B0_SPIM0_MISO>; + bias-disable; + }; + }; + + spi1_pins: spi1-pins { + pins-spi { + pinmux = <PINMUX_GPIO75__FUNC_O_SPIM1_CSB>, + <PINMUX_GPIO76__FUNC_O_SPIM1_CLK>, + <PINMUX_GPIO77__FUNC_B0_SPIM1_MOSI>, + <PINMUX_GPIO78__FUNC_B0_SPIM1_MISO>; + bias-disable; + }; + }; + + spi2_pins: spi2-pins { + pins-spi { + pinmux = <PINMUX_GPIO79__FUNC_O_SPIM2_CSB>, + <PINMUX_GPIO80__FUNC_O_SPIM2_CLK>, + <PINMUX_GPIO81__FUNC_B0_SPIM2_MOSI>, + <PINMUX_GPIO82__FUNC_B0_SPIM2_MISO>; + bias-disable; + }; + }; + + touch_pins: touch-pins { + pins-irq { + pinmux = <PINMUX_GPIO6__FUNC_B_GPIO6>; + input-enable; + bias-disable; + }; + + pins-reset { + pinmux = <PINMUX_GPIO5__FUNC_B_GPIO5>; + output-high; + }; + }; + + uart0_pins: uart0-pins { + pins { + pinmux = <PINMUX_GPIO31__FUNC_O_UTXD0>, + <PINMUX_GPIO32__FUNC_I1_URXD0>; + bias-pull-up; + }; + }; + + uart1_pins: uart1-pins { + pins { + pinmux = <PINMUX_GPIO33__FUNC_O_UTXD1>, + <PINMUX_GPIO34__FUNC_I1_URXD1>; + bias-pull-up; + }; + }; + + uart2_pins: uart2-pins { + pins { + pinmux = <PINMUX_GPIO35__FUNC_O_UTXD2>, + <PINMUX_GPIO36__FUNC_I1_URXD2>; + bias-pull-up; + }; + }; + + usb_default_pins: usb-default-pins { + pins-iddig { + pinmux = <PINMUX_GPIO83__FUNC_B_GPIO83>; + input-enable; + bias-pull-up; + }; + + pins-valid { + pinmux = <PINMUX_GPIO85__FUNC_I0_VBUSVALID>; + input-enable; + }; + + pins-vbus { + pinmux = <PINMUX_GPIO84__FUNC_O_USB_DRVVBUS>; + output-high; + }; + + }; + + usb1_default_pins: usb1-default-pins { + pins-valid { + pinmux = <PINMUX_GPIO88__FUNC_I0_VBUSVALID_1P>; + input-enable; + }; + + pins-usb-hub-3v3-en { + pinmux = <PINMUX_GPIO112__FUNC_B_GPIO112>; + output-high; + }; + }; + + wifi_pwrseq_pins: wifi-pwrseq-pins { + pins-wifi-enable { + pinmux = <PINMUX_GPIO127__FUNC_B_GPIO127>; + output-low; + }; + }; +}; + +&pmic { + interrupt-parent = <&pio>; + interrupts = <222 IRQ_TYPE_LEVEL_HIGH>; +}; + +&scp { + memory-region = <&scp_mem>; + status = "okay"; +}; + +&uart0 { + pinctrl-0 = <&uart0_pins>; + pinctrl-names = "default"; + status = "okay"; +}; + +&uart1 { + pinctrl-0 = <&uart1_pins>; + pinctrl-names = "default"; + status = "okay"; +}; + +&uart2 { + pinctrl-0 = <&uart2_pins>; + pinctrl-names = "default"; + status = "okay"; +}; + +&spi2 { + pinctrl-0 = <&spi2_pins>; + pinctrl-names = "default"; + mediatek,pad-select = <0>; + #address-cells = <1>; + #size-cells = <0>; + status = "okay"; +}; + +&u3phy0 { + status = "okay"; +}; + +&u3phy1 { + status = "okay"; +}; + +&u3phy2 { + status = "okay"; +}; + +&xhci0 { + status = "okay"; + vusb33-supply = <&mt6359_vusb_ldo_reg>; +}; + +&xhci1 { + status = "okay"; + vusb33-supply = <&mt6359_vusb_ldo_reg>; + vbus-supply = <&usb_hub_reset_1v8>; +}; + +&xhci2 { + status = "okay"; + vusb33-supply = <&mt6359_vusb_ldo_reg>; +}; -- 2.18.0