[PATCH 3/4] hwmon: max31827: Handle new properties from the devicetree

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Used fwnode to retrieve data from the devicetree in the init_client
function.

Added support for devices max31828 and max31829. For these devices, when
adi,flt-q and/or adi,alrm-pol are not mentioned, the default
configuration is loaded.

Signed-off-by: Daniel Matyas <daniel.matyas@xxxxxxxxxx>
---
 Documentation/hwmon/max31827.rst |  47 ++++++++--
 drivers/hwmon/max31827.c         | 142 +++++++++++++++++++++++++++----
 2 files changed, 165 insertions(+), 24 deletions(-)

diff --git a/Documentation/hwmon/max31827.rst b/Documentation/hwmon/max31827.rst
index 9a1055a007cf..e0eca1eb5c06 100644
--- a/Documentation/hwmon/max31827.rst
+++ b/Documentation/hwmon/max31827.rst
@@ -52,13 +52,21 @@ MAX31827 has low and over temperature alarms with an effective value and a
 hysteresis value: -40 and -30 degrees for under temperature alarm and +100 and
 +90 degrees for over temperature alarm.
 
-The alarm can be configured in comparator and interrupt mode. Currently only
-comparator mode is implemented. In Comparator mode, the OT/UT status bits have a
-value of 1 when the temperature rises above the TH value or falls below TL,
-which is also subject to the Fault Queue selection. OT status returns to 0 when
-the temperature drops below the TH_HYST value or when shutdown mode is entered.
-Similarly, UT status returns to 0 when the temperature rises above TL_HYST value
-or when shutdown mode is entered.
+The alarm can be configured in comparator and interrupt mode from the
+devicetree. In Comparator mode, the OT/UT status bits have a value of 1 when the
+temperature rises above the TH value or falls below TL, which is also subject to
+the Fault Queue selection. OT status returns to 0 when the temperature drops
+below the TH_HYST value or when shutdown mode is entered. Similarly, UT status
+returns to 0 when the temperature rises above TL_HYST value or when shutdown
+mode is entered.
+
+In interrupt mode exceeding TH also sets OT status to 1, which remains set until
+a read operation is performed on the configuration/status register (max or min
+attribute); at this point, it returns to 0. Once OT status is set to 1 from
+exceeding TH and reset, it is set to 1 again only when the temperature drops
+below TH_HYST. The output remains asserted until it is reset by a read. It is
+set again if the temperature rises above TH, and so on. The same logic applies
+to the operation of the UT status bit.
 
 Putting the MAX31827 into shutdown mode also resets the OT/UT status bits. Note
 that if the mode is changed while OT/UT status bits are set, an OT/UT status
@@ -68,6 +76,17 @@ clear the status bits before changing the operating mode.
 
 The conversions can be manual with the one-shot functionality and automatic with
 a set frequency. When powered on, the chip measures temperatures with 1 conv/s.
+The conversion rate can be modified with update_interval attribute of the chip.
+Conversion/second = 1/update_interval. Thus, the available options according to
+the data sheet are:
+	- 64000 (ms) = 1 conv/64 sec
+	- 32000 (ms) = 1 conv/32 sec
+	- 16000 (ms) = 1 conv/16 sec
+	- 4000 (ms) = 1 conv/4 sec
+	- 1000 (ms) = 1 conv/sec (default)
+	- 250 (ms) = 4 conv/sec
+	- 125 (ms) = 8 conv/sec
+
 Enabling the device when it is already enabled has the side effect of setting
 the conversion frequency to 1 conv/s. The conversion time varies depending on
 the resolution. The conversion time doubles with every bit of increased
@@ -83,8 +102,18 @@ in the writing of alarm values too. For positive numbers the user-input value
 will always be rounded down to the nearest possible value, for negative numbers
 the user-input will always be rounded up to the nearest possible value.
 
+Bus timeout resets the I2C-compatible interface when SCL is low for more than
+30ms (nominal).
+
+Alarm polarity determines if the active state of the alarm is low or high. The
+behavior for both settings is dependent on the Fault Queue setting. The ALARM
+pin is an open-drain output and requires a pullup resistor to operate.
+
+The Fault Queue bits select how many consecutive temperature faults must occur
+before overtemperature or undertemperature faults are indicated in the
+corresponding status bits.
+
 Notes
 -----
 
-Currently fault queue, alarm polarity and resolution cannot be modified.
-PEC is not implemented either.
+PEC and resolution are not implemented.
diff --git a/drivers/hwmon/max31827.c b/drivers/hwmon/max31827.c
index f05762219995..4dc14642775a 100644
--- a/drivers/hwmon/max31827.c
+++ b/drivers/hwmon/max31827.c
@@ -12,6 +12,19 @@
 #include <linux/i2c.h>
 #include <linux/mutex.h>
 #include <linux/regmap.h>
+#include <linux/hwmon-sysfs.h>
+#include <linux/of_device.h>
+
+/*
+ * gcc turns __builtin_ffsll() into a call to __ffsdi2(), which is not provided
+ * by every architecture. __ffs64() is available on all architectures, but the
+ * result is not defined if no bits are set.
+ */
+#define max31827__bf_shf(x)			 \
+	({					 \
+		typeof(x) x_ = (x);		 \
+		((x_) != 0) ? __ffs64(x_) : 0x0; \
+	})
 
 #define MAX31827_T_REG			0x0
 #define MAX31827_CONFIGURATION_REG	0x2
@@ -22,15 +35,25 @@
 
 #define MAX31827_CONFIGURATION_1SHOT_MASK	BIT(0)
 #define MAX31827_CONFIGURATION_CNV_RATE_MASK	GENMASK(3, 1)
-#define MAX31827_CONFIGURATION_U_TEMP_STAT_MASK	BIT(14)
-#define MAX31827_CONFIGURATION_O_TEMP_STAT_MASK	BIT(15)
+#define MAX31827_CONFIGURATION_TIMEOUT_MASK	BIT(5)
+#define MAX31827_CONFIGURATION_RESOLUTION_MASK	GENMASK(7, 6)
+#define MAX31827_CONFIGURATION_ALRM_POL_MASK	BIT(8)
+#define MAX31827_CONFIGURATION_COMP_INT_MASK	BIT(9)
+#define MAX31827_CONFIGURATION_FLT_Q_MASK	GENMASK(11, 10)
+#define MAX31827_CONFIGURATION_U_TEMP_STAT_MASK BIT(14)
+#define MAX31827_CONFIGURATION_O_TEMP_STAT_MASK BIT(15)
 
 #define MAX31827_12_BIT_CNV_TIME	140
 
+#define MAX31827_FLT_Q_1	0x0
+#define MAX31827_FLT_Q_4	0x2
+
 #define MAX31827_16_BIT_TO_M_DGR(x)	(sign_extend32(x, 15) * 1000 / 16)
 #define MAX31827_M_DGR_TO_16_BIT(x)	(((x) << 4) / 1000)
 #define MAX31827_DEVICE_ENABLE(x)	((x) ? 0xA : 0x0)
 
+enum chips { max31827, max31828, max31829 };
+
 enum max31827_cnv {
 	MAX31827_CNV_1_DIV_64_HZ = 1,
 	MAX31827_CNV_1_DIV_32_HZ,
@@ -58,6 +81,7 @@ struct max31827_state {
 	struct mutex lock;
 	struct regmap *regmap;
 	bool enable;
+	struct i2c_client *client;
 };
 
 static const struct regmap_config max31827_regmap = {
@@ -361,14 +385,93 @@ static int max31827_write(struct device *dev, enum hwmon_sensor_types type,
 	return -EOPNOTSUPP;
 }
 
-static int max31827_init_client(struct max31827_state *st)
+static const struct i2c_device_id max31827_i2c_ids[] = {
+       { "max31827", max31827 },
+       { "max31828", max31828 },
+       { "max31829", max31829 },
+       { }
+};
+MODULE_DEVICE_TABLE(i2c, max31827_i2c_ids);
+
+static int max31827_init_client(struct max31827_state *st,
+				struct fwnode_handle *fwnode)
 {
+	bool prop;
+	u32 data, lsb_idx;
+	unsigned int res = 0;
+	enum chips type;
+	int ret;
+
 	st->enable = true;
+	res |= MAX31827_DEVICE_ENABLE(1);
+
+	res |= MAX31827_CONFIGURATION_RESOLUTION_MASK;
 
-	return regmap_update_bits(st->regmap, MAX31827_CONFIGURATION_REG,
-				  MAX31827_CONFIGURATION_1SHOT_MASK |
-					  MAX31827_CONFIGURATION_CNV_RATE_MASK,
-				  MAX31827_DEVICE_ENABLE(1));
+	prop = fwnode_property_read_bool(fwnode, "adi,comp-int");
+	res |= FIELD_PREP(MAX31827_CONFIGURATION_COMP_INT_MASK, prop);
+
+	prop = fwnode_property_read_bool(fwnode, "adi,timeout-enable");
+	res |= FIELD_PREP(MAX31827_CONFIGURATION_TIMEOUT_MASK, !prop);
+
+	if (st->client->dev.of_node)
+		type = (enum chips)of_device_get_match_data(&st->client->dev);
+	else
+		type = i2c_match_id(max31827_i2c_ids, st->client)->driver_data;
+
+	if (fwnode_property_present(fwnode, "adi,alrm-pol")) {
+		ret = fwnode_property_read_u32(fwnode, "adi,alrm-pol", &data);
+		if (ret)
+			return ret;
+
+		res |= FIELD_PREP(MAX31827_CONFIGURATION_ALRM_POL_MASK, !!data);
+	} else {
+		switch (type) {
+		case max31827:
+		case max31828:
+			res |= FIELD_PREP(MAX31827_CONFIGURATION_ALRM_POL_MASK,
+					  0x0);
+			break;
+		case max31829:
+			res |= FIELD_PREP(MAX31827_CONFIGURATION_ALRM_POL_MASK,
+					  0x1);
+			break;
+		default:
+			return -EOPNOTSUPP;
+		}
+	}
+
+	if (fwnode_property_present(fwnode, "adi,flt-q")) {
+		ret = fwnode_property_read_u32(fwnode, "adi,flt-q", &data);
+		if (ret)
+			return ret;
+
+		/*
+		 * Convert the desired fault queue into register bits.
+		 */
+		lsb_idx = max31827__bf_shf(data);
+		if (lsb_idx > 3 || data != BIT(lsb_idx)) {
+			dev_err(&st->client->dev, "Invalid data in fault queue\n");
+			return -EOPNOTSUPP;
+		}
+
+		res |= FIELD_PREP(MAX31827_CONFIGURATION_FLT_Q_MASK, lsb_idx);
+	} else {
+		switch (type) {
+		case max31827:
+			res |= FIELD_PREP(MAX31827_CONFIGURATION_FLT_Q_MASK,
+					  MAX31827_FLT_Q_1);
+			break;
+		case max31828:
+		case max31829:
+			res |= FIELD_PREP(MAX31827_CONFIGURATION_FLT_Q_MASK,
+					  MAX31827_FLT_Q_4);
+			break;
+		default:
+			return -EOPNOTSUPP;
+		}
+	}
+
+	return regmap_write(st->regmap, MAX31827_CONFIGURATION_REG, res);
 }
 
 static const struct hwmon_channel_info *max31827_info[] = {
@@ -396,6 +499,7 @@ static int max31827_probe(struct i2c_client *client)
 	struct device *dev = &client->dev;
 	struct device *hwmon_dev;
 	struct max31827_state *st;
+	struct fwnode_handle *fwnode;
 	int err;
 
 	if (!i2c_check_functionality(client->adapter, I2C_FUNC_SMBUS_WORD_DATA))
@@ -412,7 +516,10 @@ static int max31827_probe(struct i2c_client *client)
 		return dev_err_probe(dev, PTR_ERR(st->regmap),
 				     "Failed to allocate regmap.\n");
 
-	err = max31827_init_client(st);
+	st->client = client;
+	fwnode = dev_fwnode(dev);
+
+	err = max31827_init_client(st, fwnode);
 	if (err)
 		return err;
 
@@ -423,14 +530,19 @@ static int max31827_probe(struct i2c_client *client)
 	return PTR_ERR_OR_ZERO(hwmon_dev);
 }
 
-static const struct i2c_device_id max31827_i2c_ids[] = {
-	{ "max31827", 0 },
-	{ }
-};
-MODULE_DEVICE_TABLE(i2c, max31827_i2c_ids);
-
 static const struct of_device_id max31827_of_match[] = {
-	{ .compatible = "adi,max31827" },
+	{
+		.compatible = "adi,max31827",
+		.data = (void *)max31827
+	},
+	{
+		.compatible = "adi,max31828",
+		.data = (void *)max31828
+	},
+	{
+		.compatible = "adi,max31829",
+		.data = (void *)max31829
+	},
 	{ }
 };
 MODULE_DEVICE_TABLE(of, max31827_of_match);
-- 
2.34.1




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux