On 12/09/2023 16:06, Macpaul Lin wrote:
> Add basic device-tree for the Genio 700 EVK board. The
> Genio 700 EVK is based on MediaTek MT8390 SoC.
> MT8390 hardware register maps are identical to MT8188.
>
> The Genio 700 EVK has following features:
>
...
> +
> + sdio_fixed_1v8: regulator-3 {
> + compatible = "regulator-fixed";
> + regulator-name = "sdio_io";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + enable-active-high;
> + regulator-always-on;
> + };
> +
> + sdio_fixed_3v3: regulator-4 {
> + compatible = "regulator-fixed";
> + regulator-name = "sdio_card";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + gpio = <&pio 74 0>;
Use proper defines.
> + enable-active-high;
> + regulator-always-on;
> + };
> +
> + touch0_fixed_3v3: regulator-5 {
> + compatible = "regulator-fixed";
> + regulator-name = "touch_3v3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + gpio = <&pio 119 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> +
> + usb_hub_fixed_3v3: regulator-6 {
> + compatible = "regulator-fixed";
> + regulator-name = "usb_hub_3v3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + gpio = <&pio 112 0>; /* HUB_3V3_EN */
> + startup-delay-us = <10000>;
> + enable-active-high;
> + };
> +
> + usb_hub_reset_1v8: regulator-7 {
> + compatible = "regulator-fixed";
> + regulator-name = "usb_hub_reset";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + gpio = <&pio 7 0>; /* HUB_RESET */
> + vin-supply = <&usb_hub_fixed_3v3>;
> + };
> +
> + usb_p0_vbus: regulator-8 {
> + compatible = "regulator-fixed";
> + regulator-name = "usb_p0_vbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + gpio = <&pio 84 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> +
> + usb_p1_vbus: regulator-9 {
> + compatible = "regulator-fixed";
> + regulator-name = "usb_p1_vbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + gpio = <&pio 87 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> +
> + usb_p2_vbus: regulator-10 {
> + compatible = "regulator-fixed";
> + regulator-name = "usb_p2_vbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + enable-active-high;
> + };
> +};
> +
> +&i2c0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c0_pins>;
> + clock-frequency = <400000>;
> + status = "okay";
> +
> + touchscreen@5d {
> + compatible = "goodix,gt9271";
> + reg = <0x5d>;
> + interrupt-parent = <&pio>;
> + interrupts = <6 IRQ_TYPE_EDGE_RISING>;
> + irq-gpios = <&pio 6 GPIO_ACTIVE_HIGH>;
> + reset-gpios = <&pio 5 GPIO_ACTIVE_HIGH>;
> + AVDD28-supply = <&touch0_fixed_3v3>;
> + VDDIO-supply = <&mt6359_vio18_ldo_reg>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&touch_pins>;
> + };
> +};
> +
> +&i2c1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c1_pins>;
> + clock-frequency = <400000>;
> + status = "okay";
> +};
> +
> +&i2c2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c2_pins>;
> + clock-frequency = <400000>;
> + status = "okay";
> +};
> +
> +&i2c3 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c3_pins>;
> + clock-frequency = <400000>;
> + status = "okay";
> +};
> +
> +&i2c4 {
> + pinctrl-names = "default", "default";
Why do you need two default entries? This should be just one, shouldn't it?
Best regards,
Krzysztof
