bootph-all as phase tag was added to dt-schema (dtschema/schemas/bootph.yaml) to describe various node usage during boot phases with DT. Describe the same for AM642-sk boot devices. Signed-off-by: Nishanth Menon <nm@xxxxxx> --- arch/arm64/boot/dts/ti/k3-am642-sk.dts | 29 ++++++++++++++++++++++++++ 1 file changed, 29 insertions(+) diff --git a/arch/arm64/boot/dts/ti/k3-am642-sk.dts b/arch/arm64/boot/dts/ti/k3-am642-sk.dts index 722fd285a34e..f29c8a9b59ba 100644 --- a/arch/arm64/boot/dts/ti/k3-am642-sk.dts +++ b/arch/arm64/boot/dts/ti/k3-am642-sk.dts @@ -34,6 +34,7 @@ aliases { }; memory@80000000 { + bootph-pre-ram; device_type = "memory"; /* 2G RAM */ reg = <0x00000000 0x80000000 0x00000000 0x80000000>; @@ -107,6 +108,7 @@ rtos_ipc_memory_region: ipc-memories@a5000000 { vusb_main: regulator-0 { /* USB MAIN INPUT 5V DC */ + bootph-all; compatible = "regulator-fixed"; regulator-name = "vusb_main5v0"; regulator-min-microvolt = <5000000>; @@ -117,6 +119,7 @@ vusb_main: regulator-0 { vcc_3v3_sys: regulator-1 { /* output of LP8733xx */ + bootph-all; compatible = "regulator-fixed"; regulator-name = "vcc_3v3_sys"; regulator-min-microvolt = <3300000>; @@ -128,6 +131,7 @@ vcc_3v3_sys: regulator-1 { vdd_mmc1: regulator-2 { /* TPS2051BD */ + bootph-all; compatible = "regulator-fixed"; regulator-name = "vdd_mmc1"; regulator-min-microvolt = <3300000>; @@ -234,6 +238,7 @@ led-7 { &main_pmx0 { main_mmc1_pins_default: main-mmc1-default-pins { + bootph-all; pinctrl-single,pins = < AM64X_IOPAD(0x029c, PIN_INPUT_PULLUP, 0) /* (C20) MMC1_SDWP */ AM64X_IOPAD(0x0298, PIN_INPUT_PULLUP, 0) /* (D19) MMC1_SDCD */ @@ -248,6 +253,7 @@ AM64X_IOPAD(0x027c, PIN_INPUT_PULLUP, 0) /* (K18) MMC1_DAT3 */ }; main_uart0_pins_default: main-uart0-default-pins { + bootph-all; pinctrl-single,pins = < AM64X_IOPAD(0x0238, PIN_INPUT, 0) /* (B16) UART0_CTSn */ AM64X_IOPAD(0x023c, PIN_OUTPUT, 0) /* (A16) UART0_RTSn */ @@ -257,6 +263,7 @@ AM64X_IOPAD(0x0234, PIN_OUTPUT, 0) /* (C16) UART0_TXD */ }; main_uart1_pins_default: main-uart1-default-pins { + bootph-pre-ram; pinctrl-single,pins = < AM64X_IOPAD(0x0248, PIN_INPUT, 0) /* (D16) UART1_CTSn */ AM64X_IOPAD(0x024c, PIN_OUTPUT, 0) /* (E16) UART1_RTSn */ @@ -266,12 +273,14 @@ AM64X_IOPAD(0x0244, PIN_OUTPUT, 0) /* (E14) UART1_TXD */ }; main_usb0_pins_default: main-usb0-default-pins { + bootph-all; pinctrl-single,pins = < AM64X_IOPAD(0x02a8, PIN_OUTPUT, 0) /* (E19) USB0_DRVVBUS */ >; }; main_i2c0_pins_default: main-i2c0-default-pins { + bootph-all; pinctrl-single,pins = < AM64X_IOPAD(0x0260, PIN_INPUT_PULLUP, 0) /* (A18) I2C0_SCL */ AM64X_IOPAD(0x0264, PIN_INPUT_PULLUP, 0) /* (B18) I2C0_SDA */ @@ -279,6 +288,7 @@ AM64X_IOPAD(0x0264, PIN_INPUT_PULLUP, 0) /* (B18) I2C0_SDA */ }; main_i2c1_pins_default: main-i2c1-default-pins { + bootph-all; pinctrl-single,pins = < AM64X_IOPAD(0x0268, PIN_INPUT_PULLUP, 0) /* (C18) I2C1_SCL */ AM64X_IOPAD(0x026c, PIN_INPUT_PULLUP, 0) /* (B19) I2C1_SDA */ @@ -367,6 +377,7 @@ AM64X_IOPAD(0x00bc, PIN_INPUT, 7) /* (U8) GPIO0_46 */ }; &main_uart0 { + bootph-all; status = "okay"; pinctrl-names = "default"; pinctrl-0 = <&main_uart0_pins_default>; @@ -375,12 +386,14 @@ &main_uart0 { &main_uart1 { /* main_uart1 is reserved for firmware usage */ + bootph-pre-ram; status = "reserved"; pinctrl-names = "default"; pinctrl-0 = <&main_uart1_pins_default>; }; &main_i2c0 { + bootph-all; status = "okay"; pinctrl-names = "default"; pinctrl-0 = <&main_i2c0_pins_default>; @@ -393,12 +406,14 @@ eeprom@51 { }; &main_i2c1 { + bootph-all; status = "okay"; pinctrl-names = "default"; pinctrl-0 = <&main_i2c1_pins_default>; clock-frequency = <400000>; exp1: gpio@70 { + bootph-all; compatible = "nxp,pca9538"; reg = <0x70>; gpio-controller; @@ -445,6 +460,7 @@ wlcore: wlcore@2 { &sdhci1 { /* SD/MMC */ + bootph-all; vmmc-supply = <&vdd_mmc1>; pinctrl-names = "default"; bus-width = <4>; @@ -454,11 +470,22 @@ &sdhci1 { }; &serdes_ln_ctrl { + bootph-all; idle-states = <AM64_SERDES0_LANE0_USB>; }; +&serdes_refclk { + bootph-all; +}; + +&serdes_wiz0 { + bootph-all; +}; + &serdes0 { + bootph-all; serdes0_usb_link: phy@0 { + bootph-all; reg = <0>; cdns,num-lanes = <1>; #phy-cells = <0>; @@ -468,10 +495,12 @@ serdes0_usb_link: phy@0 { }; &usbss0 { + bootph-all; ti,vbus-divider; }; &usb0 { + bootph-all; dr_mode = "host"; maximum-speed = "super-speed"; pinctrl-names = "default"; -- 2.40.0