Re: [PATCH v2 1/2] dt-bindings: i2c: Add custom properties for MAX7357/MAX7358

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi

On Thu, 31 Aug 2023 at 17:33, Krzysztof Kozlowski
<krzysztof.kozlowski@xxxxxxxxxx> wrote:
>
> On 31/08/2023 12:15, Naresh Solanki wrote:
> > From: Patrick Rudolph <patrick.rudolph@xxxxxxxxxxxxx>
> >
> > Both chips have a configuration register to enable additional
> > features. These features aren't enabled by default & it's up to
> > board designer to enable the same.
> >
> > Add booleans for:
> >  - maxim,isolate-stuck-channel
> >  - maxim,send-flush-out-sequence
> >  - maxim,preconnection-wiggle-test-enable
> >
> > Signed-off-by: Patrick Rudolph <patrick.rudolph@xxxxxxxxxxxxx>
> > Signed-off-by: Naresh Solanki <Naresh.Solanki@xxxxxxxxxxxxx>
>
> Subject: still did not improve. You waited exactly 30 minutes for my
> feedback after sending your response.
Will update the subject prefix to: 'dt-bindings: i2c: pca954x:'
Also I'm adding three properties here so I guess 'Add custom
properties..' should be fine.
If you have a better suggestion then please let me know.

>
>
>
> > ---
> > Changes in V2:
> > - Update properties.
> > ---
> >  .../bindings/i2c/i2c-mux-pca954x.yaml         | 31 +++++++++++++++++++
> >  1 file changed, 31 insertions(+)
> >
> > diff --git a/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.yaml b/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.yaml
> > index 2d7bb998b0e9..fa73eadfdf7b 100644
> > --- a/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.yaml
> > +++ b/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.yaml
> > @@ -71,6 +71,23 @@ properties:
> >      description: A voltage regulator supplying power to the chip. On PCA9846
> >        the regulator supplies power to VDD2 (core logic) and optionally to VDD1.
> >
> > +  maxim,isolate-stuck-channel:
> > +    type: boolean
> > +    description: Allows to use non faulty channels while a stuck channel is
> > +      isolated from the upstream bus. If not set all channels are isolated from
> > +      the upstream bus until the fault is cleared.
>
> Nothing improved here. As I said, please provide arguments or drop this
> property.
These features cannot be enabled by default because doing so may lead
to unexpected behavior, such as bus disconnections(although that
wasn't expected).
These features should only be enabled after they have been validated
by the board designer.
Therefore, they cannot be enabled by default.

Regards,
Naresh
>
> > +
> > +  maxim,send-flush-out-sequence:
> > +    type: boolean
> > +    description: Send a flush-out sequence to stuck auxiliary buses
> > +      automatically after a stuck channel is being detected.
>
> Ditto
>
> > +
> > +  maxim,preconnection-wiggle-test-enable:
> > +    type: boolean
> > +    description: Send a STOP condition to the auxiliary buses when the switch
> > +      register activates a channel to detect a stuck high fault. On fault the
> > +      channel is isolated from the upstream bus.
>
> Ditto
>
>
> Best regards,
> Krzysztof
>



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux