On Tue, Sep 05, 2023 at 10:32:33PM +0200, Jernej Škrabec wrote:
> On Monday, August 28, 2023 8:19:41 PM CEST Chris Morgan wrote:
> > From: Chris Morgan <macromorgan@xxxxxxxxxxx>
> >
> > The Anbernic RG-Nano is a small portable game device based on the
> > Allwinner V3s SoC. It has GPIO buttons on the face and side for
> > input, a single mono speaker, a 240x240 SPI controlled display, a USB-C
> > OTG port, an SD card slot for booting, and 64MB of RAM included in the
> > SoC.
> >
> > Working/Tested:
> > - SDMMC
> > - UART (for debugging)
> > - Buttons
> > - Charging/battery/PMIC
> > - Speaker
> > - RTC
> > - USB Host and Gadget*
> > - Display (at 60hz)
> >
> > *There is an issue with the usb_phy where it forces the device to host
> > mode. Until the phy driver is fixed this can be bypassed by either
> > removing the phy references from the ohci and ehci nodes or by setting
> > the usbphy on the ohci and ehci nodes to 1 (which is incorrect).
>
> DT is HW description, so driver independent and above comment should be
> removed from commit message.
>
> Otherwise:
> Acked-by: Jernej Skrabec <jernej.skrabec@xxxxxxxxx>
>
> Best regards,
> Jernej
Should I resubmit with the text removed, or can it be edited before
being sent upstream?
Thank you.
>
> >
> > Signed-off-by: Chris Morgan <macromorgan@xxxxxxxxxxx>
> > ---
> > arch/arm/boot/dts/allwinner/Makefile | 1 +
> > .../allwinner/sun8i-v3s-anbernic-rg-nano.dts | 284 ++++++++++++++++++
> > 2 files changed, 285 insertions(+)
> > create mode 100644
> > arch/arm/boot/dts/allwinner/sun8i-v3s-anbernic-rg-nano.dts
> >
> > diff --git a/arch/arm/boot/dts/allwinner/Makefile
> > b/arch/arm/boot/dts/allwinner/Makefile index 589a1ce1120a..2be83a1edcbb
> > 100644
> > --- a/arch/arm/boot/dts/allwinner/Makefile
> > +++ b/arch/arm/boot/dts/allwinner/Makefile
> > @@ -237,6 +237,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \
> > sun8i-t113s-mangopi-mq-r-t113.dtb \
> > sun8i-t3-cqa3t-bv3.dtb \
> > sun8i-v3-sl631-imx179.dtb \
> > + sun8i-v3s-anbernic-rg-nano.dtb \
> > sun8i-v3s-licheepi-zero.dtb \
> > sun8i-v3s-licheepi-zero-dock.dtb \
> > sun8i-v40-bananapi-m2-berry.dtb
> > diff --git a/arch/arm/boot/dts/allwinner/sun8i-v3s-anbernic-rg-nano.dts
> > b/arch/arm/boot/dts/allwinner/sun8i-v3s-anbernic-rg-nano.dts new file mode
> > 100644
> > index 000000000000..bcccb0d3f9ce
> > --- /dev/null
> > +++ b/arch/arm/boot/dts/allwinner/sun8i-v3s-anbernic-rg-nano.dts
> > @@ -0,0 +1,284 @@
> > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> > +
> > +/dts-v1/;
> > +#include <dt-bindings/input/linux-event-codes.h>
> > +#include "sun8i-v3s.dtsi"
> > +#include "sunxi-common-regulators.dtsi"
> > +
> > +/ {
> > + model = "Anbernic RG Nano";
> > + compatible = "anbernic,rg-nano", "allwinner,sun8i-v3s";
> > +
> > + aliases {
> > + serial0 = &uart0;
> > + };
> > +
> > + backlight: backlight {
> > + compatible = "pwm-backlight";
> > + brightness-levels = <0 1 2 3 8 14 21 32 46 60 80 100>;
> > + default-brightness-level = <11>;
> > + power-supply = <®_vcc5v0>;
> > + pwms = <&pwm 0 40000 1>;
> > + };
> > +
> > + chosen {
> > + stdout-path = "serial0:115200n8";
> > + };
> > +
> > + gpio_keys: gpio-keys {
> > + compatible = "gpio-keys";
> > +
> > + button-a {
> > + gpios = <&gpio_expander 12 (GPIO_ACTIVE_LOW |
> GPIO_PULL_UP)>;
> > + label = "BTN-A";
> > + linux,code = <BTN_EAST>;
> > + };
> > +
> > + button-b {
> > + gpios = <&gpio_expander 14 (GPIO_ACTIVE_LOW |
> GPIO_PULL_UP)>;
> > + label = "BTN-B";
> > + linux,code = <BTN_SOUTH>;
> > + };
> > +
> > + button-down {
> > + gpios = <&gpio_expander 1 (GPIO_ACTIVE_LOW |
> GPIO_PULL_UP)>;
> > + label = "DPAD-DOWN";
> > + linux,code = <BTN_DPAD_DOWN>;
> > + };
> > +
> > + button-left {
> > + gpios = <&gpio_expander 4 (GPIO_ACTIVE_LOW |
> GPIO_PULL_UP)>;
> > + label = "DPAD-LEFT";
> > + linux,code = <BTN_DPAD_LEFT>;
> > + };
> > +
> > + button-right {
> > + gpios = <&gpio_expander 0 (GPIO_ACTIVE_LOW |
> GPIO_PULL_UP)>;
> > + label = "DPAD-RIGHT";
> > + linux,code = <BTN_DPAD_RIGHT>;
> > + };
> > +
> > + button-se {
> > + gpios = <&gpio_expander 7 (GPIO_ACTIVE_LOW |
> GPIO_PULL_UP)>;
> > + label = "BTN-SELECT";
> > + linux,code = <BTN_SELECT>;
> > + };
> > +
> > + button-st {
> > + gpios = <&gpio_expander 6 (GPIO_ACTIVE_LOW |
> GPIO_PULL_UP)>;
> > + label = "BTN-START";
> > + linux,code = <BTN_START>;
> > + };
> > +
> > + button-tl {
> > + gpios = <&gpio_expander 2 (GPIO_ACTIVE_LOW |
> GPIO_PULL_UP)>;
> > + label = "BTN-L";
> > + linux,code = <BTN_TL>;
> > + };
> > +
> > + button-tr {
> > + gpios = <&gpio_expander 15 (GPIO_ACTIVE_LOW |
> GPIO_PULL_UP)>;
> > + label = "BTN-R";
> > + linux,code = <BTN_TR>;
> > + };
> > +
> > + button-up {
> > + gpios = <&gpio_expander 3 (GPIO_ACTIVE_LOW |
> GPIO_PULL_UP)>;
> > + label = "DPAD-UP";
> > + linux,code = <BTN_DPAD_UP>;
> > + };
> > +
> > + button-x {
> > + gpios = <&gpio_expander 11 (GPIO_ACTIVE_LOW |
> GPIO_PULL_UP)>;
> > + label = "BTN-X";
> > + linux,code = <BTN_NORTH>;
> > + };
> > +
> > + button-y {
> > + gpios = <&gpio_expander 13 (GPIO_ACTIVE_LOW |
> GPIO_PULL_UP)>;
> > + label = "BTN-Y";
> > + linux,code = <BTN_WEST>;
> > + };
> > + };
> > +};
> > +
> > +&ccu {
> > + clocks = <&osc24M>, <&osc32k>;
> > +};
> > +
> > +&codec {
> > + allwinner,audio-routing = "Speaker", "HP",
> > + "MIC1", "Mic",
> > + "Mic", "HBIAS";
> > + allwinner,pa-gpios = <&pio 5 6 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>;
> /* PF6
> > */ + status = "okay";
> > +};
> > +
> > +&ehci {
> > + status = "okay";
> > +};
> > +
> > +&i2c0 {
> > + status = "okay";
> > +
> > + gpio_expander: gpio@20 {
> > + compatible = "nxp,pcal6416";
> > + reg = <0x20>;
> > + gpio-controller;
> > + #gpio-cells = <2>;
> > + #interrupt-cells = <2>;
> > + interrupt-controller;
> > + interrupt-parent = <&pio>;
> > + interrupts = <1 3 IRQ_TYPE_EDGE_BOTH>; /* PB3/EINT3 */
> > + vcc-supply = <®_vcc3v3>;
> > + };
> > +
> > + axp209: pmic@34 {
> > + reg = <0x34>;
> > + interrupt-parent = <&pio>;
> > + interrupts = <1 5 IRQ_TYPE_EDGE_FALLING>; /* PB5/EINT5
> */
> > + };
> > +
> > + pcf8563: rtc@51 {
> > + compatible = "nxp,pcf8563";
> > + reg = <0x51>;
> > + };
> > +};
> > +
> > +#include "axp209.dtsi"
> > +
> > +&battery_power_supply {
> > + status = "okay";
> > +};
> > +
> > +&mmc0 {
> > + broken-cd;
> > + bus-width = <4>;
> > + disable-wp;
> > + vmmc-supply = <®_vcc3v3>;
> > + vqmmc-supply = <®_vcc3v3>;
> > + status = "okay";
> > +};
> > +
> > +&ohci {
> > + status = "okay";
> > +};
> > +
> > +&pio {
> > + clocks = <&ccu CLK_BUS_PIO>, <&osc24M>, <&osc32k>;
> > + vcc-pb-supply = <®_vcc3v3>;
> > + vcc-pc-supply = <®_vcc3v3>;
> > + vcc-pf-supply = <®_vcc3v3>;
> > + vcc-pg-supply = <®_vcc3v3>;
> > +
> > + spi0_no_miso_pins: spi0-no-miso-pins {
> > + pins = "PC1", "PC2", "PC3";
> > + function = "spi0";
> > + };
> > +};
> > +
> > +&pwm {
> > + pinctrl-0 = <&pwm0_pin>;
> > + pinctrl-names = "default";
> > + status = "okay";
> > +};
> > +
> > +/* DCDC2 wired into vdd-cpu, vdd-sys, and vdd-ephy. */
> > +®_dcdc2 {
> > + regulator-always-on;
> > + regulator-max-microvolt = <1250000>;
> > + regulator-min-microvolt = <1250000>;
> > + regulator-name = "vdd-cpu";
> > +};
> > +
> > +/* DCDC3 wired into every 3.3v input that isn't the RTC. */
> > +®_dcdc3 {
> > + regulator-always-on;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-min-microvolt = <3300000>;
> > + regulator-name = "vcc-io";
> > +};
> > +
> > +/*
> > + * LDO1 wired into RTC, voltage is hard-wired at 3.3v and cannot be
> > + * software modified. Note that setting voltage here to 3.3v for accuracy
> > + * sake causes an issue with the driver that causes it to fail to probe
> > + * because of a voltage constraint in the driver.
> > + */
> > +®_ldo1 {
> > + regulator-always-on;
> > + regulator-name = "vcc-rtc";
> > +};
> > +
> > +/* LDO2 wired into VCC-PLL and audio codec. */
> > +®_ldo2 {
> > + regulator-always-on;
> > + regulator-max-microvolt = <3000000>;
> > + regulator-min-microvolt = <3000000>;
> > + regulator-name = "vcc-pll";
> > +};
> > +
> > +/* LDO3, LDO4, and LDO5 unused. */
> > +®_ldo3 {
> > + status = "disabled";
> > +};
> > +
> > +®_ldo4 {
> > + status = "disabled";
> > +};
> > +
> > +/* External RTC used instead, internal RTC runs fast. */
> > +&rtc {
> > + status = "disabled";
> > +};
> > +
> > +&spi0 {
> > + pinctrl-0 = <&spi0_no_miso_pins>;
> > + pinctrl-names = "default";
> > + status = "okay";
> > +
> > + display@0 {
> > + compatible = "saef,sftc154b", "panel-mipi-dbi-spi";
> > + reg = <0>;
> > + backlight = <&backlight>;
> > + dc-gpios = <&pio 2 0 GPIO_ACTIVE_HIGH>; /* PC0 */
> > + reset-gpios = <&pio 1 2 GPIO_ACTIVE_HIGH>; /* PB2 */
> > + spi-max-frequency = <100000000>;
> > +
> > + height-mm = <39>;
> > + width-mm = <39>;
> > +
> > + /* Set hb-porch to compensate for non-visible area */
> > + panel-timing {
> > + hactive = <240>;
> > + vactive = <240>;
> > + hback-porch = <80>;
> > + vback-porch = <0>;
> > + clock-frequency = <0>;
> > + hfront-porch = <0>;
> > + hsync-len = <0>;
> > + vfront-porch = <0>;
> > + vsync-len = <0>;
> > + };
> > + };
> > +};
> > +
> > +&uart0 {
> > + pinctrl-0 = <&uart0_pb_pins>;
> > + pinctrl-names = "default";
> > + status = "okay";
> > +};
> > +
> > +&usb_otg {
> > + dr_mode = "otg";
> > + status = "okay";
> > +};
> > +
> > +&usb_power_supply {
> > + status = "okay";
> > +};
> > +
> > +&usbphy {
> > + usb0_id_det-gpios = <&pio 6 5 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /*
> PG5 */
> > + status = "okay";
> > +};
>
>
>
>
