Re: [PATCH 1/2] media: dt-bindings: imx519: Add IMX519 DT bindings

[Sakari Ailus <sakari.ailus@xxxxxx>]

Hi Umang,

On Thu, Jul 27, 2023 at 09:11:07PM +0530, Umang Jain wrote:
> From: Lee Jackson <lee.jackson@xxxxxxxxxxx>
> 
> Add YAML device tree binding documentation for IMX519 CMOS
> image sensor.
> 
> Signed-off-by: Umang Jain <umang.jain@xxxxxxxxxxxxxxxx>
> ---
>  .../bindings/media/i2c/sony,imx519.yaml       | 113 ++++++++++++++++++
>  1 file changed, 113 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/media/i2c/sony,imx519.yaml
> 
> diff --git a/Documentation/devicetree/bindings/media/i2c/sony,imx519.yaml b/Documentation/devicetree/bindings/media/i2c/sony,imx519.yaml
> new file mode 100644
> index 000000000000..6f38b09890d2
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/media/i2c/sony,imx519.yaml
> @@ -0,0 +1,113 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/media/i2c/imx519.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Sony 1/2.5-Inch 16Mpixel CMOS Digital Image Sensor
> +
> +maintainers:
> +  - Lee Jackson <lee.jackson@xxxxxxxxxxx>
> +
> +description: |-
> +  The Sony IMX519 is a 1/2.5-inch CMOS active pixel digital image sensor
> +  with an active array size of 4656H x 3496V. It is programmable through
> +  I2C interface. The I2C address is fixed to 0x1A as per sensor data sheet.
> +  Image data is sent through MIPI CSI-2, which is configured as either 2 or
> +  4 data lanes.
> +
> +properties:
> +  compatible:
> +    const: sony,imx519
> +
> +  reg:
> +    description: I2C device address
> +    maxItems: 1
> +
> +  clocks:
> +    maxItems: 1
> +
> +  VDIG-supply:
> +    description:
> +      Digital I/O voltage supply, 1.05 volts
> +
> +  VANA-supply:
> +    description:
> +      Analog voltage supply, 2.8 volts
> +
> +  VDDL-supply:
> +    description:
> +      Digital core voltage supply, 1.8 volts
> +
> +  reset-gpios:
> +    description: |-
> +      Reference to the GPIO connected to the xclr pin, if any.
> +      Must be released (set high) after all supplies and INCK are applied.
> +
> +  # See ../video-interfaces.txt for more details
> +  port:
> +    type: object
> +    properties:
> +      endpoint:
> +        type: object
> +        properties:

I think you should have, something alike (from mipi-ccs.yaml):

  port:
    $ref: /schemas/graph.yaml#/$defs/port-base
    additionalProperties: false

    properties:
      endpoint:
        $ref: /schemas/media/video-interfaces.yaml#
        unevaluatedProperties: false


See mipi-ccs.yaml on examples for some properties below. E.g.
link-frequencies is described in video-interfaces.yaml, no need to describe
it here.

> +          data-lanes:
> +            description: |-
> +              The sensor supports either two-lane, or four-lane operation.
> +              For two-lane operation the property must be set to <1 2>.
> +            items:
> +              - const: 1
> +              - const: 2

I guess the device also supports single lane operation?

In any case minItems/maxItems here should be enough.

> +
> +          clock-noncontinuous:
> +            type: boolean
> +            description: |-
> +              MIPI CSI-2 clock is non-continuous if this property is present,
> +              otherwise it's continuous.
> +
> +          link-frequencies:
> +            allOf:
> +              - $ref: /schemas/types.yaml#/definitions/uint64-array
> +            description:
> +              Allowed data bus frequencies.
> +
> +        required:
> +          - link-frequencies
> +
> +required:
> +  - compatible
> +  - reg
> +  - clocks
> +  - VANA-supply
> +  - VDIG-supply
> +  - VDDL-supply
> +  - port
> +
> +additionalProperties: false
> +
> +examples:
> +  - |
> +    i2c0 {
> +        #address-cells = <1>;
> +        #size-cells = <0>;
> +
> +        imx519: sensor@1a {
> +            compatible = "sony,imx519";
> +            reg = <0x1a>;
> +            clocks = <&imx519_clk>;
> +            VANA-supply = <&imx519_vana>;   /* 2.8v */
> +            VDIG-supply = <&imx519_vdig>;   /* 1.05v */
> +            VDDL-supply = <&imx519_vddl>;   /* 1.8v */
> +
> +            port {
> +                imx519_0: endpoint {
> +                    remote-endpoint = <&csi1_ep>;
> +                    data-lanes = <1 2>;
> +                    clock-noncontinuous;
> +                    link-frequencies = /bits/ 64 <408000000>;
> +                };
> +            };
> +        };
> +    };
> +
> +...

-- 
Kind regards,

Sakari Ailus