On Wed Aug 30, 2023 at 4:57 PM CEST, Doug Anderson wrote:
> Hi,
>
> On Wed, Aug 30, 2023 at 7:43 AM Luca Weiss <luca.weiss@xxxxxxxxxxxxx> wrote:
> >
> > On Wed Aug 30, 2023 at 4:30 PM CEST, Doug Anderson wrote:
> > > Hi,
> > >
> > > On Wed, Aug 30, 2023 at 2:58 AM Luca Weiss <luca.weiss@xxxxxxxxxxxxx> wrote:
> > > >
> > > > On some platforms like sc7280 on non-ChromeOS devices the core clock
> > > > cannot be touched by Linux so we cannot provide it. Mark it as optional
> > > > as accessing qfprom works without it.
> > > >
> > > > Signed-off-by: Luca Weiss <luca.weiss@xxxxxxxxxxxxx>
> > > > ---
> > > > drivers/nvmem/qfprom.c | 2 +-
> > > > 1 file changed, 1 insertion(+), 1 deletion(-)
> > >
> > > Are you actually testing burning fuses from the OS, or are you just
> > > using the nvmem in "read-only" mode? From comments in the bindings, if
> > > you're trying to burn the fuses then the clock is required. If things
> > > are in read-only mode then the clock isn't required.
> >
> > Hi Doug,
> >
> > I definitely don't plan on burning any fuses on this phone. Not even
> > sure that's allowed by the TZ / boot stack.
> >
> > >
> > > When I compare to the driver, it seems like the driver assumes that if
> > > more than one memory region is provided then you must be supporting
> > > burning fuses. The bindings agree that having 4 memory regions
> > > specified means that the nvmem supports burning and 1 memory region
> > > specified means read-only. The extra 3 memory regions in the nvmem are
> > > all about fuse burning, I believe.
> > >
> > > So maybe the right fix here is to just change your dts to specify one
> > > memory region?
> >
> > I got feedback from Konrad that this here would be the preferred
> > approach compared to having a different dts for ChromeOS vs non-ChromeOS
> > devices. I don't feel strongly to either, for me it's also okay to
> > remove the extra memory regions and only have the main one used on
> > regular qcom devices.
> >
> > Let me know what you think.
>
> I don't hate the idea of leaving the extra memory regions in the dts.
> They do describe the hardware, after all, even if the main OS can't
> actually access those memory regions. ...though the same could also be
> said about the clock you've removed. Said another way: if you want to
> fully describe the hardware then the dts should have the extra memory
> regions and the clock. If you are OK w/ just describing the hardware
> in the way that the OS has access to then the dts should not have the
> extra memory regions and not have the clock. Does that sound right?
Not sure which of those memory regions are actually accessible on this
board, but honestly I don't even want to try accessing it. Blowing fuses
is not my wish there ;)
On downstream the node is just described like the following:
qfprom: qfprom@780000 {
compatible = "qcom,qfprom";
reg = <0x780000 0x7000>;
...
};
So we have 0x780000 - 0x786fff here.
In sc7280.dtsi we have the following:
qfprom: efuse@784000 {
compatible = "qcom,sc7280-qfprom", "qcom,qfprom";
reg = <0 0x00784000 0 0xa20>,
<0 0x00780000 0 0xa20>,
<0 0x00782000 0 0x120>,
<0 0x00786000 0 0x1fff>;
...
};
So I guess this:
* 0x780000 - 0x780a1f
* 0x782000 - 0x78211f
* 0x784000 - 0x784a1f
* 0x786000 - 0x787ffe
So at least the last memory region seems to be partially out of range
according to downstream.
So after reading all of this I tried running this commmand on the phone
and the phone reboots into 900e mode.
$ cat /sys/devices/platform/soc@0/784000.efuse/qfprom0/nvmem
I guess normally this should work? So if I interpret this correctly, the
Linux driver thinks it can access more than it can/should. But also
should probably try this command on another chipset to see if it works
on any really?
Regards
Luca
>
> If somehow you do end up with something like your patch, though,
> you're still missing a bit. Specifically, you don't want to "enable
> writing" a few lines below if you didn't get the clock, right?
>
> -Doug
