On Fri, 18 Aug 2023 10:43:17 +0200
Martin Botka <martin.botka@xxxxxxxxxxxxxx> wrote:
Hi Martin,
many thanks for the time and effort for upstreaming this!
> Add support for the thermal sensor found in H616 SoC
> which slightly resembles the H6 thermal sensor
> controller with few changes like 4 sensors.
>
> Signed-off-by: Martin Botka <martin.botka@xxxxxxxxxxxxxx>
> ---
> drivers/thermal/sun8i_thermal.c | 115 ++++++++++++++++++++++++++++++++++++++++
> 1 file changed, 115 insertions(+)
>
> diff --git a/drivers/thermal/sun8i_thermal.c b/drivers/thermal/sun8i_thermal.c
> index 195f3c5d0b38..9d73e4313ad8 100644
> --- a/drivers/thermal/sun8i_thermal.c
> +++ b/drivers/thermal/sun8i_thermal.c
> @@ -108,6 +108,12 @@ static int sun50i_h5_calc_temp(struct ths_device *tmdev,
> return -1590 * reg / 10 + 276000;
> }
>
> +static int sun50i_h616_calc_temp(struct ths_device *tmdev,
> + int id, int reg)
> +{
> + return (reg + tmdev->chip->offset) * tmdev->chip->scale;
So if my school maths is not letting me down, this is the same as the
sun8i_ths_calc_temp() function, when using:
scale = h616_scale * -10
offset = h616_offset * h616_scale
So we do not need this new function, when we use:
+ .offset = 263655,
+ .scale = 810,
below, right?
Those values are not only positive, but also seem closer to the other
SoC's values.
This of course requires some small adjustment in the calibrate function,
to accommodate for the changed scale, but I leave this up as an exercise
to the reader ;-)
Martin, can you confirm that this works?
> +}
> +
> static int sun8i_ths_get_temp(struct thermal_zone_device *tz, int *temp)
> {
> struct tsensor *s = thermal_zone_device_priv(tz);
> @@ -278,6 +284,64 @@ static int sun50i_h6_ths_calibrate(struct ths_device *tmdev,
> return 0;
> }
>
> +static int sun50i_h616_ths_calibrate(struct ths_device *tmdev,
> + u16 *caldata, int callen)
nit: alignment
> +{
> + struct device *dev = tmdev->dev;
> + int i, ft_temp;
> +
> + if (!caldata[0])
> + return -EINVAL;
> +
> + /*
> + * h616 efuse THS calibration data layout:
> + *
> + * 0 11 16 27 32 43 48 57
> + * +----------+-----------+-----------+-----------+
> + * | temp | |sensor0| |sensor1| |sensor2| |
> + * +----------+-----------+-----------+-----------+
> + * ^ ^ ^
> + * | | |
> + * | | sensor3[11:8]
> + * | sensor3[7:4]
> + * sensor3[3:0]
> + *
> + * The calibration data on the H616 is the ambient temperature and
> + * sensor values that are filled during the factory test stage.
> + *
> + * The unit of stored FT temperature is 0.1 degreee celusis.
nit: degree Celsius
> + */
> + ft_temp = caldata[0] & FT_TEMP_MASK;
> +
> + for (i = 0; i < tmdev->chip->sensor_num; i++) {
> + int delta, cdata, offset, reg;
> +
> + if (i == 3)
> + reg = (caldata[1] >> 12)
> + | (caldata[2] >> 12 << 4)
> + | (caldata[3] >> 12 << 8);
Can you add parentheses around the (caldata[2|3] >> 12) part? Makes it a
bit more readable.
> + else
> + reg = (int)caldata[i + 1] & TEMP_CALIB_MASK;
> +
> + delta = (ft_temp * 100 - tmdev->chip->calc_temp(tmdev, i, reg))
> + / tmdev->chip->scale;
Looks a bit odd, can you write this as over two lines?
delta = ft_temp ...;
delta /= tmdev->chip_scale;
(And this would be the place where you adjust the calculation to use the
new scale value).
> + cdata = CALIBRATE_DEFAULT - delta;
> + if (cdata & ~TEMP_CALIB_MASK) {
> + dev_warn(dev, "sensor%d is not calibrated.\n", i);
> +
> + continue;
> + }
> +
> + offset = (i % 2) * 16;
> + regmap_update_bits(tmdev->regmap,
> + SUN50I_H6_THS_TEMP_CALIB + (i / 2 * 4),
> + 0xfff << offset,
That should be TEMP_CALIB_MASK << offset, compare the H6 code.
> + cdata << offset);
> + }
> +
> + return 0;
> +}
> +
> static int sun8i_ths_calibrate(struct ths_device *tmdev)
> {
> struct nvmem_cell *calcell;
> @@ -453,6 +517,43 @@ static int sun50i_h6_thermal_init(struct ths_device *tmdev)
> return 0;
> }
>
> +static int sun50i_h616_thermal_init(struct ths_device *tmdev)
> +{
> + int val;
> +
> + /*
> + * T_acq = 20us
> + * clkin = 24MHz
> + *
> + * x = T_acq * clkin - 1
> + * = 479
> + */
> + regmap_write(tmdev->regmap, SUN50I_THS_CTRL0,
> + SUN8I_THS_CTRL0_T_ACQ0(47) | SUN8I_THS_CTRL2_T_ACQ1(479));
So this whole function is the same as the H6 (diff it!), except this line.
Which is actually also the same, just written differently (47 == 0x2f).
Can you please double check this, and if you agree, remove the whole
function and just use the H6 version?
Cheers,
Andre
> + /* average over 4 samples */
> + regmap_write(tmdev->regmap, SUN50I_H6_THS_MFC,
> + SUN50I_THS_FILTER_EN |
> + SUN50I_THS_FILTER_TYPE(1));
> + /*
> + * clkin = 24MHz
> + * filter_samples = 4
> + * period = 0.25s
> + *
> + * x = period * clkin / 4096 / filter_samples - 1
> + * = 365
> + */
> + regmap_write(tmdev->regmap, SUN50I_H6_THS_PC,
> + SUN50I_H6_THS_PC_TEMP_PERIOD(365));
> + /* enable sensor */
> + val = GENMASK(tmdev->chip->sensor_num - 1, 0);
> + regmap_write(tmdev->regmap, SUN50I_H6_THS_ENABLE, val);
> + /* thermal data interrupt enable */
> + val = GENMASK(tmdev->chip->sensor_num - 1, 0);
> + regmap_write(tmdev->regmap, SUN50I_H6_THS_DIC, val);
> +
> + return 0;
> +}
> +
> static int sun8i_ths_register(struct ths_device *tmdev)
> {
> int i;
> @@ -608,6 +709,19 @@ static const struct ths_thermal_chip sun50i_h6_ths = {
> .calc_temp = sun8i_ths_calc_temp,
> };
>
> +static const struct ths_thermal_chip sun50i_h616_ths = {
> + .sensor_num = 4,
> + .has_bus_clk_reset = true,
> + .ft_deviation = 8000,
> + .offset = -3255,
> + .scale = -81,
> + .temp_data_base = SUN50I_H6_THS_TEMP_DATA,
> + .calibrate = sun50i_h616_ths_calibrate,
> + .init = sun50i_h616_thermal_init,
> + .irq_ack = sun50i_h6_irq_ack,
> + .calc_temp = sun50i_h616_calc_temp,
> +};
> +
> static const struct of_device_id of_ths_match[] = {
> { .compatible = "allwinner,sun8i-a83t-ths", .data = &sun8i_a83t_ths },
> { .compatible = "allwinner,sun8i-h3-ths", .data = &sun8i_h3_ths },
> @@ -616,6 +730,7 @@ static const struct of_device_id of_ths_match[] = {
> { .compatible = "allwinner,sun50i-a100-ths", .data = &sun50i_a100_ths },
> { .compatible = "allwinner,sun50i-h5-ths", .data = &sun50i_h5_ths },
> { .compatible = "allwinner,sun50i-h6-ths", .data = &sun50i_h6_ths },
> + { .compatible = "allwinner,sun50i-h616-ths", .data = &sun50i_h616_ths },
> { /* sentinel */ },
> };
> MODULE_DEVICE_TABLE(of, of_ths_match);
>
