Hi Dave, On Tue, Aug 01, 2023 at 03:22:17PM +0100, Dave Stevenson wrote: > On Mon, 31 Jul 2023 at 22:55, Laurent Pinchart wrote: > > > > Hello, > > > > This series is an attempt to revive support for pinmuxed I2C0 on the > > Raspberry Pi BCM2711-based board. > > > > On BCM2711-based boards, the I2C0 controller can be muxed between pins > > 0+1 or 44+45. The former is exposed through the 40-pins GPIO connector, > > and the latter is used for the RTC on the CM4 I/O board, but also routed > > to the display and camera connectors on the Raspberry Pi 4B board. The > > other BCM2711-based board, the Raspberry Pi 400, does not expose or > > connect anything to pins 44+45. > > > > A previous version was posted ([1]) a year and a half ago by Uwe. It > > bundled the pinmuxing and RTC in a single patch, with the mux added to > > the CM4 I/O board device tree. This version splits this in two, and > > moves the pinumxing to the bcm2711-rpi.dtsi to also support the > > Raspberry Pi 4B. > > > > The Raspberry Pi downstream kernel has a more complex DT architecture in > > order to support different I2C0 pinmuxing for other boards. Two files, > > bcm283x-rpi-i2c0mux_0_28.dtsi and bcm283x-rpi-i2c0mux_0_44.dtsi, define > > the two I2C0 pinxmuxing options (pins 0+1 and 28+29, or pins 0+1 and > > 44+45). Each board .dts then includes the appropriate file. I'm hoping > > to avoid this additional complexity for now, by addressing the I2C0 > > pinmuxing for BCM2711-based boards only. If/when support for I2C0 > > pinmuxing on boards will be needed, we can revisit this topic. > > > > Compared to the Raspberry Pi downstream kernel, the two muxed I2C buses > > are labelled i2c0_0 and i2c0_1 instead of i2c0 and i2c_csi_dsi. This > > change was made to keep the naming of the I2C controller labels > > consistent, avoiding renaming of the I2C0 controller's label from i2c0 > > to i2c0if. > > > > Dave, are you fine with the differences between this patch series and > > the downstream kernel, or do you expect them to cause issues ? > > I've checked with Phil. There's nothing too untoward that will cause > us any significant grief. Thanks for checking. In the meantime, I realized that the CM4S is 2711-based and, according to the downstream DT, multiplexes I2C0 on pins 28+29, not 44+45 :-( Umang and Kieran also told me that we want to test camera support on the Pi 3B. It looks like the only viable approach to support all that will be to include per-board I2C0 pinmux .dtsi as done in the downstream kernel. I'll send a v5. > Phil has commented that the RTC is an PCF85063AT, so that compatible > string should be "nxp,pcf85063a" if you actually want to make use of > the alarm output. > Then again the driver support for the alarm output appears to want it > routed to an IRQ rather than as a system reset/wakeup, so it probably > makes little difference. It llargely depends on how exact you want to > be in your hardware description. I'll update the compatible string, it's an easy change and it's nice to be accurate. > > [1] https://lore.kernel.org/linux-arm-kernel/20211231115109.94626-1-uwe@xxxxxxxxxxxxxxxxx/ > > > > Uwe Kleine-König (2): > > ARM: dts: bcm2711-rpi: Add pinctrl-based multiplexing for I2C0 > > ARM: dts: bcm2711-rpi-cm4-io: Add RTC on I2C0 > > > > arch/arm/boot/dts/bcm2711-rpi-cm4-io.dts | 16 ++++++++++++ > > arch/arm/boot/dts/bcm2711-rpi.dtsi | 31 ++++++++++++++++++++++++ > > 2 files changed, 47 insertions(+) -- Regards, Laurent Pinchart
