Re: [PATCH v2 08/10] HID: i2c-hid: Support being a panel follower

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi,

On Mon, Jul 17, 2023 at 11:15 AM Doug Anderson <dianders@xxxxxxxxxxxx> wrote:
>
> Benjamin,
>
> On Mon, Jun 26, 2023 at 3:49 PM Doug Anderson <dianders@xxxxxxxxxxxx> wrote:
> >
> > Benjamin,
> >
> > On Thu, Jun 8, 2023 at 8:37 AM Benjamin Tissoires
> > <benjamin.tissoires@xxxxxxxxxx> wrote:
> > >
> > > > +static const struct drm_panel_follower_funcs i2c_hid_core_panel_follower_funcs = {
> > > > +     .panel_prepared = i2c_hid_core_panel_prepared,
> > > > +     .panel_unpreparing = i2c_hid_core_panel_unpreparing,
> > > > +};
> > >
> > > Can we make that above block at least behind a Kconfig?
> > >
> > > i2c-hid is often used for touchpads, and the notion of drm panel has
> > > nothing to do with them. So I'd be more confident if we could disable
> > > that code if not required.
> >
> > Now that other concerns are addressed, I started trying to write up a
> > v3 and I found myself writing this as the description of the Kconfig
> > entry:
> >
> > --
> > config I2C_HID_SUPPORT_PANEL_FOLLOWER
> > bool "Support i2c-hid devices that must be power sequenced with a panel"
> >
> > Say Y here if you want support for i2c-hid devices that need to
> > coordinate power sequencing with a panel. This is typically important
> > when you have a panel and a touchscreen that share power rails or
> > reset GPIOs. If you say N here then the kernel will not try to honor
> > any shared power sequencing for your hardware. In the best case,
> > ignoring power sequencing when it's needed will draw extra power. In
> > the worst case this will prevent your hardware from functioning or
> > could even damage your hardware.
> >
> > If unsure, say Y.
> >
> > --
> >
> > I can certainly go that way, but I just wanted to truly make sure
> > that's what we want. Specifically:
> >
> > 1. If we put the panel follower code behind a Kconfig then we actually
> > have no idea if a touchscreen was intended to be a panel follower.
> > Specifically the panel follower API is the one that detects the
> > connection between the panel and the i2c-hid device, so without being
> > able to call the panel follower API we have no idea that an i2c-hid
> > device was supposed to be a panel follower.
> >
> > 2. It is conceivable that power sequencing a device incorrectly could
> > truly cause hardware damage.
> >
> > Together, those points mean that if you turn off the Kconfig entry and
> > then try to boot on a device that needed that Kconfig setting that you
> > might damage hardware. I can code it up that way if you want, but it
> > worries me...
> >
> >
> > Alternatives that I can think of:
> >
> > a) I could change the panel follower API so that panel followers are
> > in charge of detecting the panel that they follow. Today, that looks
> > like:
> >
> >        panel_np = of_parse_phandle(dev->of_node, "panel", 0);
> >        if (panel_np)
> >                /* It's a panel follower */
> >        of_node_put(panel_np);
> >
> > ...so we could put that code in each touchscreen driver and then fail
> > to probe i2c-hid if we detect that we're supposed to be a panel
> > follower but the Kconfig is turned off. The above doesn't seem
> > massively ideal since it duplicates code. Also, one reason why I put
> > that code in drm_panel_add_follower() is that I think this concept
> > will eventually be needed even for non-DT cases. I don't know how to
> > write the non-DT code right now, though...
> >
> >
> > b) I could open-code detect the panel follower case but leave the
> > actual linking to the panel follower API. AKA add to i2c-hid:
> >
> >        if (of_property_read_bool(dev->of_node, "panel"))
> >                /* It's a panel follower */
> >
> > ...that's a smaller bit of code, but feels like an abstraction
> > violation. It also would need to be updated if/when we added support
> > for non-DT panel followers.
> >
> >
> > c) I could add a "static inline" implementation of b) to "drm_panel.h".
> >
> > That sounds great and I started doing it. ...but then realized that it
> > means adding to drm_panel.h:
> >
> > #include <linux/device.h>
> > #include <linux/of.h>
> >
> > ...because otherwise of_property_read_bool() isn't defined and "struct
> > device" can't be dereferenced. That might be OK, but it looks as if
> > folks have been working hard to avoid things like this in header
> > files. Presumably it would get uglier if/when we added the non-DT
> > case, as well. That being said, I can give it a shot...
> >
> > --
> >
> > At this point, I'm hoping for some advice. How important is it for you
> > to have a Kconfig for "I2C_HID_SUPPORT_PANEL_FOLLOWER"?
> >
> > NOTE: even if I don't add the Kconfig, I could at least create a
> > function for registering the panel follower that would get most of the
> > panel follower logic out of the probe function. Would that be enough?
>
> I'd love to send a new version of this patch series, but I'm still
> stuck with the above issue. I'm hoping you might have a minute to
> provide your thoughts. If I don't hear anything, I'll try a v3 where I
> don't have the Kconfig for "I2C_HID_SUPPORT_PANEL_FOLLOWER" but just
> try to pull a little more of the code out of the probe function.

To provide breadcrumbs, I posted the v3 which pulls a bit more code
out of the probe function but is otherwise largely unchanged. The
cover letter for v3 can be found at:

https://lore.kernel.org/r/20230725203545.2260506-1-dianders@xxxxxxxxxxxx/




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux