The IP supports per channel interrupt, when intel adds the per channel
interrupt support, the per channel irq is from MSI vector, but this
feature can also be supported on non-MSI platforms. Renaming
multi_msi_en to perch_irq_en to reflects this fact.
Signed-off-by: Jisheng Zhang <jszhang@xxxxxxxxxx>
---
drivers/net/ethernet/stmicro/stmmac/dwmac-intel.c | 4 ++--
drivers/net/ethernet/stmicro/stmmac/dwmac4_dma.c | 2 +-
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c | 8 ++++----
include/linux/stmmac.h | 4 ++--
4 files changed, 9 insertions(+), 9 deletions(-)
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-intel.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-intel.c
index 0ffae785d8bd..99a072907008 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-intel.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-intel.c
@@ -953,7 +953,7 @@ static int stmmac_config_single_msi(struct pci_dev *pdev,
res->irq = pci_irq_vector(pdev, 0);
res->wol_irq = res->irq;
- plat->flags &= ~STMMAC_FLAG_MULTI_MSI_EN;
+ plat->flags &= ~STMMAC_FLAG_PERCH_IRQ_EN;
dev_info(&pdev->dev, "%s: Single IRQ enablement successful\n",
__func__);
@@ -1005,7 +1005,7 @@ static int stmmac_config_multi_msi(struct pci_dev *pdev,
if (plat->msi_sfty_ue_vec < STMMAC_MSI_VEC_MAX)
res->sfty_ue_irq = pci_irq_vector(pdev, plat->msi_sfty_ue_vec);
- plat->flags |= STMMAC_FLAG_MULTI_MSI_EN;
+ plat->flags |= STMMAC_FLAG_PERCH_IRQ_EN;
dev_info(&pdev->dev, "%s: multi MSI enablement successful\n", __func__);
return 0;
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac4_dma.c b/drivers/net/ethernet/stmicro/stmmac/dwmac4_dma.c
index 84d3a8551b03..9bf8adf466a2 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac4_dma.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac4_dma.c
@@ -175,7 +175,7 @@ static void dwmac4_dma_init(void __iomem *ioaddr,
value = readl(ioaddr + DMA_BUS_MODE);
- if (dma_cfg->multi_msi_en) {
+ if (dma_cfg->perch_irq_en) {
value &= ~DMA_BUS_MODE_INTM_MASK;
value |= (DMA_BUS_MODE_INTM_MODE1 << DMA_BUS_MODE_INTM_SHIFT);
}
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
index 15ed3947361b..c97bebfd04f8 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
@@ -3722,7 +3722,7 @@ static int stmmac_request_irq(struct net_device *dev)
int ret;
/* Request the IRQ lines */
- if (priv->plat->flags & STMMAC_FLAG_MULTI_MSI_EN)
+ if (priv->plat->flags & STMMAC_FLAG_PERCH_IRQ_EN)
ret = stmmac_request_irq_multi_msi(dev);
else
ret = stmmac_request_irq_single(dev);
@@ -6007,7 +6007,7 @@ static void stmmac_poll_controller(struct net_device *dev)
if (test_bit(STMMAC_DOWN, &priv->state))
return;
- if (priv->plat->flags & STMMAC_FLAG_MULTI_MSI_EN) {
+ if (priv->plat->flags & STMMAC_FLAG_PERCH_IRQ_EN) {
for (i = 0; i < priv->plat->rx_queues_to_use; i++)
stmmac_msi_intr_rx(0, &priv->dma_conf.rx_queue[i]);
@@ -7278,8 +7278,8 @@ int stmmac_dvr_probe(struct device *device,
priv->plat = plat_dat;
priv->ioaddr = res->addr;
priv->dev->base_addr = (unsigned long)res->addr;
- priv->plat->dma_cfg->multi_msi_en =
- (priv->plat->flags & STMMAC_FLAG_MULTI_MSI_EN);
+ priv->plat->dma_cfg->perch_irq_en =
+ (priv->plat->flags & STMMAC_FLAG_PERCH_IRQ_EN);
priv->dev->irq = res->irq;
priv->wol_irq = res->wol_irq;
diff --git a/include/linux/stmmac.h b/include/linux/stmmac.h
index 11671fd6adee..76249117c0ff 100644
--- a/include/linux/stmmac.h
+++ b/include/linux/stmmac.h
@@ -96,7 +96,7 @@ struct stmmac_dma_cfg {
int mixed_burst;
bool aal;
bool eame;
- bool multi_msi_en;
+ bool perch_irq_en;
bool dche;
};
@@ -211,7 +211,7 @@ struct dwmac4_addrs {
#define STMMAC_FLAG_TSO_EN BIT(4)
#define STMMAC_FLAG_SERDES_UP_AFTER_PHY_LINKUP BIT(5)
#define STMMAC_FLAG_VLAN_FAIL_Q_EN BIT(6)
-#define STMMAC_FLAG_MULTI_MSI_EN BIT(7)
+#define STMMAC_FLAG_PERCH_IRQ_EN BIT(7)
#define STMMAC_FLAG_EXT_SNAPSHOT_EN BIT(8)
#define STMMAC_FLAG_INT_SNAPSHOT_EN BIT(9)
#define STMMAC_FLAG_RX_CLK_RUNS_IN_LPI BIT(10)
--
2.40.1
