Re: [PATCH 1/5] arm64: dts: qcom: Add base SM4450 DTSI

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 





在 7/19/2023 6:22 PM, Krzysztof Kozlowski 写道:
On 19/07/2023 12:01, Tengfei Fan wrote:
This add based DTSI for SM4450 SoC and includes base description of
CPUs and interrupt-controller which helps to boot to shell with
console on boards with this SoC.

Signed-off-by: Tengfei Fan <quic_tengfan@xxxxxxxxxxx>

Thank you for your patch. There is something to discuss/improve.


---
  arch/arm64/boot/dts/qcom/sm4450.dtsi | 435 +++++++++++++++++++++++++++
  1 file changed, 435 insertions(+)
  create mode 100644 arch/arm64/boot/dts/qcom/sm4450.dtsi

diff --git a/arch/arm64/boot/dts/qcom/sm4450.dtsi b/arch/arm64/boot/dts/qcom/sm4450.dtsi
new file mode 100644
index 000000000000..ab14aecbdcea
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sm4450.dtsi
@@ -0,0 +1,435 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023, Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	interrupt-parent = <&intc>;
+
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	chosen { };
+
+	clocks{
+		xo_board: xo_board {

Please start your work from scratch from mainline SoC, so we won't have
to point you all these obvious issues which we fixed long time ago. Just
pick the most recent SoC, like SM8550.
sure will pick like SM8550 and reference it.

+			compatible = "fixed-clock";
+			clock-frequency = <76800000>;
+			#clock-cells = <0>;
+		};
+
+		sleep_clk: sleep_clk {
+			compatible = "fixed-clock";
+			clock-frequency = <32000>;
+			#clock-cells = <0>;
+		};
+	};

...

+		};
+	};
+
+	firmware {
+		scm: scm {
+			compatible = "qcom,scm-sm4450", "qcom,scm";

Undocumented compatible. If you plan to document it further, then please
check if your patches are correctly ordered. Bindings are always before
their users.
will remove this SCM node due to haven't use currently, and will check other undocumented compatible and document it.

+			#reset-cells = <1>;
+		};
+	};
+
+	memory@a0000000 {
+		device_type = "memory";
+		/* We expect the bootloader to fill in the size */
+		reg = <0x0 0xa0000000 0x0 0x0>;
+	};
+
+	pmu {
+		compatible = "arm,armv8-pmuv3";
+		interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	psci {
+		compatible = "arm,psci-1.0";
+		method = "smc";
+
+		CPU_PD0: power-domain-cpu0 {
+			#power-domain-cells = <0>;
+			power-domains = <&CLUSTER_PD>;
+			domain-idle-states = <&LITTLE_CPU_SLEEP_0>;
+		};
+
+		CPU_PD1: power-domain-cpu1 {
+			#power-domain-cells = <0>;
+			power-domains = <&CLUSTER_PD>;
+			domain-idle-states = <&LITTLE_CPU_SLEEP_0>;
+		};
+
+		CPU_PD2: power-domain-cpu2 {
+			#power-domain-cells = <0>;
+			power-domains = <&CLUSTER_PD>;
+			domain-idle-states = <&LITTLE_CPU_SLEEP_0>;
+		};
+
+		CPU_PD3: power-domain-cpu3 {
+			#power-domain-cells = <0>;
+			power-domains = <&CLUSTER_PD>;
+			domain-idle-states = <&LITTLE_CPU_SLEEP_0>;
+		};
+
+		CPU_PD4: power-domain-cpu4 {
+			#power-domain-cells = <0>;
+			power-domains = <&CLUSTER_PD>;
+			domain-idle-states = <&BIG_CPU_SLEEP_0>;
+		};
+
+		CPU_PD5: power-domain-cpu5 {
+			#power-domain-cells = <0>;
+			power-domains = <&CLUSTER_PD>;
+			domain-idle-states = <&BIG_CPU_SLEEP_0>;
+		};
+
+		CPU_PD6: power-domain-cpu6 {
+			#power-domain-cells = <0>;
+			power-domains = <&CLUSTER_PD>;
+			domain-idle-states = <&BIG_CPU_SLEEP_0>;
+		};
+
+		CPU_PD7: power-domain-cpu7 {
+			#power-domain-cells = <0>;
+			power-domains = <&CLUSTER_PD>;
+			domain-idle-states = <&BIG_CPU_SLEEP_0>;
+		};
+
+		CLUSTER_PD: power-domain-cpu-cluster0 {
+			#power-domain-cells = <0>;
+			domain-idle-states = <&CLUSTER_SLEEP_0>, <&CLUSTER_SLEEP_1>;
+		};
+	};
+
+	soc: soc@0 {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges = <0 0 0 0 0x10 0>;
+		dma-ranges = <0 0 0 0 0x10 0>;
+		compatible = "simple-bus";
+
+		tcsr_mutex: hwlock@1f40000 {
+			compatible = "qcom,tcsr-mutex";
+			reg = <0x0 0x01f40000 0x0 0x40000>;
+			#hwlock-cells = <1>;
+		};
+
+		pdc: interrupt-controller@b220000 {
+			compatible = "qcom,sm4450-pdc", "qcom,pdc";
+			reg = <0 0x0b220000 0 0x30000>, <0 0x174000f0 0 0x64>;
+			qcom,pdc-ranges = <0 480 94>, <94 494 31>, <125 63 1>;
+			#interrupt-cells = <2>;
+			interrupt-parent = <&intc>;
+			interrupt-controller;
+		};
+
+		intc: interrupt-controller@17200000 {
+			compatible = "arm,gic-v3";
+			#interrupt-cells = <3>;
+			interrupt-controller;
+			#redistributor-regions = <1>;
+			redistributor-stride = <0x0 0x20000>;
+			reg = <0x0 0x17200000 0x0 0x10000>,     /* GICD */
+				<0x0 0x17260000 0x0 0x100000>;    /* GICR * 8 */

reg is always after compatible. Then ranges follow.
will update sequence.

Also, indentation looks not aligned here.
V2 patch will aligne.

+			interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_LOW>;
+		};
+
+		timer@17420000 {
+			compatible = "arm,armv7-timer-mem";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0 0 0x20000000>;
+			reg = <0x0 0x17420000 0x0 0x1000>;

Same problem... some weird ordering.
will update sequence.

+			clock-frequency = <19200000>;

Are you sure this property is allowed in new designs?
will remove this property.

+
+			frame@17421000 {
+				frame-number = <0>;
+				interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+						<GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x17421000 0x1000>,
+					<0x17422000 0x1000>;
+			};
+
+			frame@17423000 {
+				frame-number = <1>;
+				interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x17423000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@17425000 {
+				frame-number = <2>;
+				interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x17425000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@17427000 {
+				frame-number = <3>;
+				interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x17427000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@17429000 {
+				frame-number = <4>;
+				interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x17429000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@1742b000 {
+				frame-number = <5>;
+				interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x1742b000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@1742d000 {
+				frame-number = <6>;
+				interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x1742d000 0x1000>;
+				status = "disabled";
+			};
+		};
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+				<GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+				<GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+				<GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>;
+		clock-frequency = <19200000>;

Are you sure this property is allowed in new designs?
will remove this property.

+	};
+};

Best regards,
Krzysztof


--
Thx and BRs,
Tengfei Fan



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux